Having problems with your Vacuums ?

Windtunnel belt Tell me how to install please


Answers :

You didn't state your model number, they have different ones. Take off the bottom plate, the belt and brushroll will be exposed. If you canned see the motor shaft to put the belt on, then the top cover will have to removed also. Usually is a couple of screws from the bottom to take out, then you wil see a slot on each side from the bottom, use a flat blade screwdriver, put intoi slot and pry up to release locking tabs, top will come off. Belt goes from brush roll to motor shaft. If this is the model that uses 2 belts, then the belt goes from the motor shaft to the bigger pulley, and the Vee belt goes from the smalled pulley to the brush roll.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Windtunnel belt Tell me how to install please


You didn't state your model number, they have different ones. Take off the bottom plate, the belt and brushroll will be exposed. If you canned see the motor shaft to put the belt on, then the top cover will have to removed also. Usually is a coupl ... Vacuums

Hoover F6025900 Steam Vac Widepath LS, I own this steam vac and I found bits of rubber under the machine when I turned it on, smelled like burned rubber from a belt? Can you please tell me if there is a belt on this carpet cleaner and if so, how to access the belt? I have taken out some screws and still cant get to the belt? Thanks


Well there is no belt, and not sure what the rubber would be from, everything is plastic or metal. Unless it is really an electrical smell, which means the motor is going bad.\015\012\015\012 ... Hoover Vacuums

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Dirt Devil Swivel Glide Vac with a broken belt. I have purchased the correct belt(#4).The bottom is off and I cannot tell where the belt connects to. Please help. Jann


It connects to the left side with the little metal rod sticking out.then connect to the wooden roller. in the space without the brush on it. roll the wooden piece to check if everything moves. then put back together. ... Dirt Devil Vacuums

I have a Hoover Windtunnel U5472-940. The belt broke so I replaced it. Immediately the next one broke. The belt goes around the brush cylinder and a metal post. I think there is supposed to be something on the metal post to protect the belt but I can't tell from the owner's manual. I also can't find out if this is a part that can be replaced. I've only had the vacuum about a year and a half. Thanks


You may have something in your brush bearing that does not allow the brush to turn easily thus stretching the belt. Chris ... Hoover U6455-900 WindTunnel Vacuum

I have a Fantom Fury and need to replace the belt. Please tell me how to get into it so the belt can be replaced. It is a Fantom Fury Vacuum Cleaner # 3680093 Fantom Technologies Model # F10051 01


... Vacuums

Belt replacement can you tell me how i replace the belt on my electrolux velocity hoover please


Need to know if it is a Electrolux or a Hoover and the model number. ... Vacuums

Where does it go and how do I replace the belt on a Deluxe Hoover Mach 3.8 bagged windtunnel action vacuum? I kno it goes somewhere around the brush but it fell off when opened and I can't tell where it goes. I have a replacement belt


... Hoover Vacuums

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

Could you please tell me how to replace a belt on hoover please


Please identify the product model number.\015\012It will be on the data label, probably a UXXXX-XXX series. ... Vacuums

My hoover turbo cyclonic needs a new belt replacement I 'am not sure how to change it please tell me how to change the belt


... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Drive belts im from Sydney,Australia please can you tell me where i can get a belt from i have tryed everywhere thankyou


You can find parts on Ebay stores buy it now and usually you end up saving alot of money. I bought like 36 generic bags for the price of 9 genuine Kirby bags. They also have genuine Kirby supplies too check it out! ... Kirby Heritage II Vacuum

Can you tell me how to change belt on onn vacuum please?


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How to install belt - Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum


Hello,This information can be found in the user guide/manual for the unit, found here:http://www.vacuum-home.com/manuals/Hoover-U578090 ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Hi i have got a Dyson dco4 it switches on but the roller doesn't go round. I have checked the belt which has gone so I have no idea what else it could be please could you tell me what else it could be


If the belt is gone, then you need a new belt. Otherwise, ensure floor select switch is set to ON.\015\012\015\012If you don't have a user's manual, you can use the below site to get one free.\015\012 ... Dyson Vacuums

Hello, we have a dirt devil vaccum cleaner (model MO84600) is not grabbing the dust...belt and filter are in a good condition.can u please tell me the problem...


... Dirt Devil Vacuums

I asked about how to replace a belt on my sebo cleaner automatic X1 I have lost the answer can you tell me again please?


This machine has two toothed belts and it makes sense to change both while you're at it. Incidentally, this is a job you shouldn't have to do very often - Sebo belts usually last at least 10 years. So, here's how to get at the belts ... Sebo Automatic X1 Bagged Upright Vacuum

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

Please tell me where I can get a new belt for my Vaccum Cleaner it is a Russell Hobbs upright Pet Master I am in Kempton Park the Model No. is CLONIC1800.


Try Moshoeu Appliance Repairs at 32 Voortrekker St.or phone them on 011 394-6487, If they have not got the right thing they may have one that fits, get one for you or tell you where to get one. You could also phone Kl ... Vacuums

How to install a U8172-900 belt - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


Your savvy bagless has a geared belt. remove the bottom plate and then remove the 2 back screws near the back wheels to remove the top cover also peel off the hoover decal to access the top cover screw. this will expose all components to replace the ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Eureka Altima vacuum. The model number is 2996. I don't think my vacumm is sucking any dust. Plus, it smells like a burning leather. What should I do? I have tried to get help from others and they tell me that I should change the belt. But, I don't know where it is. Please help.


Sounds like the belt for sure. Here is a link with the owners manual. It shows how to get to and change the belt. http://www.eureka.com/index.php?option=com_productdisplay&view=productdisplay&task=getproducts&productid=2&produ ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

How do I install a hoover windtunnel vacuum cleaner belt. The bagless one,.


First, take it outside or to the basement. This can get messy. Turn the vacuum cleaner upside down. Remove four 1-1/2" self-tapping screws that hold the bottom cover in place (where the beater bar is.) Remove this and you will see where the belts go; ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

On several occasions the belt has come off the Hoover Windtunnel beater shaft and had to be re-installed. Is there any way to prevent it from slipping off? The shaft seems to be made so that the middle if it is wider(thicker than either the end or the part closer to the motor, which, to me, is a bad design so I don't know how to overcome this problem. I'd be very grateful for a permanent solution to this problem. Thanks in Advance, mas


Your belt is stretched and needs replacement ( # 38528035 ) . The agitator is crowned so that the belt stays centered. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Hoover windtunnel T series. Model #UH70105. The system check indicator was almost red so I cleaned the filter. There are no clogs and it vacuums fine without the hose, but when I go to use the hose there is very little suction and all the vacuum dust flys out of the end the hose piece fits into when not in use. Can you please tell me what is wrong?


... Hoover Vacuums

Good Morning, A friend recently gave me her Hoover windtunnel model U630-900 vacuum. It is a self propelled vac. It comes on but is hard to push and will not really pick up any dust particles on the carpet. It has a funny smell also. I saw where one of you Q & A you said to check the roller brush. I thought maybe a belt may be off or something, but I do not have a manual to know where to begin checking. Could you tell what to check and also if there is anywhere online to download the manua


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4559 seconds