Having problems with your Vacuums ?

I have a hoover windtunnel u5757-900 and the motor stops in the mittle of the operation, no restrictions


Answers :

When the motor stops, this is usually caused by an restriction in air flow...caused by a full bag, dirty filter or blockage. do you wait for about 30 minuites and it you can turn it on again? have you changed th dirt cup filter in the last 2 years? have you ever washed the dirt cup filter? if you have washed it, you should not have, however, once washed and dried the fibers would have expanded and will cause a restricted air flow condition.If all of this check ok, you may still have an electrical issue, and would recomend bringing that to a trusted Vac shop.
Repair Help & Product Troubleshooting for Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a hoover windtunnel u5757-900 and the motor stops in the mittle of the operation, no restrictions


When the motor stops, this is usually caused by an restriction in air flow...caused by a full bag, dirty filter or blockage. do you wait for about 30 minuites and it you can turn it on again? have you changed th dirt cup filter in the last 2 years? h ... Vacuums

I have a Hoover Windtunnel 2 upright vvacum cleaner. During regular use my wife turned it on and it staarted cleaning, then all of a sudden it stopped and then started again then stopped for good. I unclugged the hose, cleane4de the brushes , blew the main filer and still cannot get it to start. The motor seemed hotter than usual. Can you help me? Lenny Rentz e-mail [email protected]


Actually, if you don't have continuity, then you have an open, not a short. ... Vacuums

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga


I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Replace motor hoover windtunnel - Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum


... Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum

Hoover WindTunnel Canister: Roller brush motor not turning


These motors have a fuse incorporated in the field winding and it sounds like that blew. These motors sometimes overheat at the front bearing and the bearing will melt into the plastic housing. This will cause the fuse to blow. It sounds like that's ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t


... Hoover Vacuums

My 20" Patton electric fan has stopped working. I use it for animal cooling and it operates in dusty conditions. I suspect that the motor is shot. Is it worthwhile to replace the motor and are motors even available?


You could just try to clean the motor out by taking it apart, and shining the shaft up. then put some motor oil/engine oil on the shaft. That will work 99% of the time. ... Vacuums

Dyson dc25 motor only works when hoover down, stops when upright


... Dyson DC25 Animal Bagless Upright Vacuum

My Hoover duros s3590 just stopped running. The motor started up and then just powered down and won't start back up. Is this a faulty on/off switch or a motor problem. I'm weighing the +/- to fix or buy a new vac. TIA


... Maytag Hoover Duros S3590 Vacuum (Canister)

We have a hoover porta vac. that at first it would sometimes come on and sometimes not. It did completely stop coming on, so I have changed the switch and the cord but with no luck. Could you offer any suggestions or is this a motor situation. To my knowledge the motor was not making any noise. Your help would be greatly appreciated. Thank You, Molly Maid of NW Fla.


If this has had heavy use, the carbons in the motor may be worn. ... Hoover CH30000 Bagged Canister Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi


Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

Why doe my hoover mach3 stop during operation? I have to wait until the moter cools down.Then i turn on the switch normal way.Then a few minutes latter it stops again.


Your Hoover is stopping because it is overheating. This is a sure sign that there is a blockage somewhere. Find the blockage and clear it, and that should solve the problem. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover u5781-900, motor shuts off (intermittent)when you shake vac or make jerky movements.If you move vac to up right position the vac starts right up.When you giggle vac, motor starts and stops no mater if you just started up or vac for ran for 45 min. Thanks Lucy C.


Lucy\015\012you have a bad connection somewhere in the unit\015\012this is a fire hazard and you should not use this until its been fixed\015\012could be a pinched wire or broken connections ... Vacuums

Hoover windtunnel..runs fine for 5 minutes then stops?


OK - sounds like your machine has a blockage somewhere. Follow manufacturer's instructions for clearing blockages and all should be well. If you no longer have the manual, you can download it from the Hoover website.\015\012\015\012Good luck! ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I need help in disasembling my hoover windtunnel to check the motor brushes


... Hoover Vacuums

Hoover windtunnel mach 6.1 stops working filters are clean has a new bag


... Vacuums

How to remove the motor on a hoover windtunnel?


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover steamvac's motor stop working


... Hoover V1 SteamVac SpinScrub Vacuum

Hepa filter stopped on Hoover Windtunnel 2 Model #U8361-900


This has a simple solution IF you have a air compressor with a high pressure nozzle. Outside the house, first remove the Dust bin completely and lay the unit down with the dust bin area up. now start blowing the nozzle at the hepa filter, Alot of ... Vacuums

Hoover windtunnel trys to start but then stops


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0707 seconds