Having problems with your Alto 302000414 Attix 8 AS/E Canister Wet/Dry Vacuum ?

My Alto Attix wap kew dos not work - Alto 302000414 Attix 8 AS/E Canister Wet/Dry Vacuum


Answers :

Repair Help & Product Troubleshooting for Alto 302000414 Attix 8 AS/E Canister Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Alto Attix wap kew dos not work - Alto 302000414 Attix 8 AS/E Canister Wet/Dry Vacuum


... Alto 302000414 Attix 8 AS/E Canister Wet/Dry Vacuum

How do i change an Alto halogen light bulb - Alto 302000414 Attix 8 AS/E Canister Wet/Dry Vacuum


I am sure you worked it out by now, but for anyone else who is looking; the fitting should have come with a suction cap to attach to the front of the bulb like a plunger to pull the bulb out... terrible design! \015\012Jake ... Alto 302000414 Attix 8 AS/E Canister Wet/Dry Vacuum

Is this a double insulated device? - Dayton 3VE22 Canister WetDry Vacuum


If the cord plug is two prong, yes. If it's three prong (two flat, one round) no. Most all vacuums for the past many years are double insulated even though they don't state that. ... Dayton 3VE22 Canister WetDry Vacuum

Dayton shop vac 3VE18 manual - Dayton Audio 3VE18 Canister WetDry Vacuum


... Dayton Audio 3VE18 Canister WetDry Vacuum

Need on/off switch - Shop Vac QPL650 Canister WetDry Vacuum


... Shop Vac QPL650 Canister WetDry Vacuum

I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope


Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums

When we turn on the vacuum, the canister falls open. The clips holding the canister in place do not seem to hold the canister tightly which I'm sure that it did in the past. The clips do not look bent, but every time we turn on the vacuum the intense pressure blows the canister open only remaining attached the the rest of the vacuum by one clip


Check filter and make sure it is kept clean at regular intervals. Possibly worn out clip retainers on cannister side due to excessive pressure build up. Do not force closure unless pressure is back to normal. May crack cannister or damage unit beyond ... Hayden Industries SuperVac 6000 Central System Vacuum

My Hoover s5620 central vacuum is not sucking. I cleaned out the canister and vacuumed the inside bag in the canister. The hose is clear as is the central vacuums tubing. Any suggestions ?


Try getting some compressed air source and blow back whatever is stuck in the hose. ... Vacuums

Overheated vacuum After I finished vacuuming the library last night I changed the bag and shook out both filters and vacuum would not restart. The canister unit felt real warm to the touch but I had been using it a least 1/2 hour non stop. The bag was pretty full but not overly so. It's a Simplicity canister with power head. The carpet is long shag from the 70's Did it just over heat? Thanks Shauna


It normally won't over heat unless the bag is too full, the filters are clogged, or you have have a clog in the hose or down by the brush roll, the inlet may be clogged. Some will restart after a while, some others have a reset to push. If it won't ... Simplicity 7850 Premier Bagged Canister Vacuum

25512/ 25513 Progressive Canister Vacuum: HI, we have a kenmore progressive canister vacuum ...


Cord bad at male prongs, or fuse near motor blown. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Replace hose on kenmore 3.9 canister vacuum - Kenmore 25512/ 25513 Progressive Canister Vacuum


... Kenmore 25512/ 25513 Progressive Canister Vacuum

Open canister on red miela vacuum - Miele S251i Plus Bagged Canister Vacuum


Try this linkhttp://www.sannerud.com/house/miele.html ... Miele S251i Plus Bagged Canister Vacuum

Hello, I have a Kenmore Progressive Canister Vacuum 116.20912006. It won't turn on. On the hose assembly, the end where the hose swivel is, there are 4 metal pins that plug into the canister. One of the pins looks like it broke off. There are only three pins remaining. I assume there should be four pins as there are four holes. Is this the problem and is it fixable? The vacuum is from 2002 so I am not sure a replacement part is even available and at what price. Thank you. Susan susan.eng@


Hi Susan, if the pin has broken off you can do one of two things, first, would be to find a local vacuum repair shop and take it there for them to look at. they may be able to look at the hose and fix it for you pretty cheaply. what ... Kenmore Progressive 20912 Bagged Canister Vacuum

No suction on my Dyson canister vacuum. - Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum


Hey,I see this problem is more frequent..I'm guessing your dyson 'sounds' blocked.See my solution:http://www.fixya.com/support/t4547920-loss_suctionThis fixed mine right up.It was not working well at ALL, so i open ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Kenmore canister vacuum model #116 - Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Need a hose for shark ep 238 canister vacuum - Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum


... Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum

I have any easy-flo built-in vacuum. I recently had the bearings on the motor, top and bottom replaced. I put the vacuum back together and it mow has low suction power. There is plenty of suction on the side of the canister where the rigid tubing meets the canister body but little suction at the wall plates. Any ideas? Roger


There is either a blockage or a pipe is open somewhere. You should check the system at the wall valve without the hose to determine if the pipes are blocked or if perhaps the hose is plugged. If one of the wall valves is damaged or open, this will af ... Vacuums

My canister vacuum is losing suction (oreck) - Oreck Super-Deluxe BB870AD Bagged Canister Vacuum


... Oreck Super-Deluxe BB870AD Bagged Canister Vacuum

My Kenmore canister vacuum cleaner model 116.27514700 has unacceptably low suction.It is much less than my older GE Walmart canister vacuum. the 2 filters are very clean and there is no blockage in the hose and the dust collection bag is empty. Is poor suction a characteristic of this model or if not is there a way to fix this problem?


... Panasonic Kenmore Canister Vacuum Vacuum

Where is fuse kenmore canister vacuum - Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum


... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Roaring vacuum My vacuum begins to roar shortly after I turn it on. The sound seems to be coming from the middle of the canister. When I take the recoil cord off, there is a plate just under it still on the canister that is extremely hot. Any idea what could be wrong and how to fix it?


Good day,your problem seem that it is plug if you have no suckiong ,place the hose on the exaust that should un plug the hose,or the motor has had some dirt et it and plug the intake ,that is why it roars try this,later ... Electrolux UltraLux 2000 Bagged Canister Vacuum

How do i open my canister vacuum - Electrolux UltraLux 2000 Bagged Canister Vacuum


Open the bag door and grip the bumpers with a set of pliers. The bumpers cover a set of locking keys which will slide all the way forward and out. The back of the vac will then lift off and the top and bottom will open hinging forward like a **** she ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have a central vacuum system. When I disconnect the hose from a wall outlet the central canister does not shut down dispite my turning off the vacuum at the handle of the hose. The only way I can get the system to shut down is to pull the plug at the canister. What gives? Rob


What I'm hearing is the canister(Not the Powerhead) portion of the unit is running all the time unless you unplug it. this problem could be caused by a short in one of your low voltage lines running through the house. To determine that just unplug on ... Vacuums

I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!


Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum

Miele canister vacuum over heating - Miele Cat & Dog 326i Bagged Canister Vacuum


... Miele Cat & Dog 326i Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0875 seconds