Having problems with your Bad c88w2b ?

How to take apart to empty

Need to take apart to empty and clean

Answers :

Repair Help & Product Troubleshooting for Bad c88w2b

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Suction is not good. It is more hassle to empty. You have to take apart top filter & pull out everything stuck uptop. I end up with more dust on the outside when I change. I miss my bags. No dirt to deal with.


Yeah i agree with you...Sometimes you have to disconnect the primary vacuum hose at both ends and clear the debris in it..Then take the plastic top off the motor houseing and clean it out aswell...Its a pain rest assured :) ... Eureka 5849A Boss Bagless Upright Cyclonic Vacuum

My Reliable T730A Canister Steam Vacuum is not working. The red (empty) light stays on even though its full and it doesn't produce any steam. I doubt that the water is getting down into the heating chamber. How easy is it to take apart and clean or can I just blow compressed air through it? Any help most appreciated. Steve [email protected]


You can probably just blow it out with the air compressor. If you have a air pressure regulator on the air compressor then I would turn it down to about 30-40 psi. Then try to blow out the line. ... Reliable T730A Canister Steam Vacuum

My Hoover SteamVac has been doing a wonderful job but in two instances, after emptying the dirty water and reattaching the reservoir, the machine has lost suction. The first time I was able to make it work again after taking it apart and putting it back together about 10 times. I don't know what I did that fixed it but as long as it worked again, I was happy. But it's happened again and I can't get it to vacuum. I can see that it isn't clogged. Can you please help me????


Look for the lower tank filter to be clean. also make sure the lower tank lid is on properly. latch when installed on machine. Make sure the front panel duct is on the lower tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

How do I take it apart to empty the cone? - Dirt Devil KONE Hand Vacuum MO213BLU Vacuum


The cone where the dirt goes in will twist off about 1/4 turn and then lift out the filter to empty ... Dirt Devil KONE Hand Vacuum MO213BLU Vacuum

I have had my Bissell 6591-X for 2 years. I hate it! No matter what I do all the fuzz, hair, whatever fills up around the upper filter before it even starts to deposit in the cup. It has done this ever since I bought it. No matter how much I take it apart, clean it, clean filters, empty the cup, nothing does any good. I spill more dirt onto the vacuum and floor than ever gets in the cup. I will never buy another Bissell.


Sure your not over filling it ? ... Bissell Vacuums

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet


Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

E series How did you take your rainbow e series apart? Do you have a manual? I've got a few pieces off mine but can't see where any other screws are to completly take apart to be able to look at motor. Thanks Kelly


The clear lenses on either side of the top part of the E-series Rainbow are removable. If you look at the each lens you will see two sections on the top edge of each lens that looks like this |___| |___| about 1 1/2 inches in from each end. Put a ... Rainbow E series Canister Wet/Dry Vacuum

Cable stuck in machine (sphera 20). How do I take apart to release cable please? I cannot see any visible screws to take the machine apart. Cable will not retract or come out of machine


... Bosch Vacuums

I need to take the canister apart to screw the filter housing back in place. I can't figure out how to take the canister apart or another way to screw the filter housing back in place.


You did not identify your model and the TriStar website does not provide manuals. They do have a FAQ page which does provide some illustrated guidance which may be helpful. See here:\015\012\015\01 ... Tristar Vacuums

I need to take the canister apart to screw the filter housing back in place. I can't figure out how to take the canister apart or another way to screw the filter housing back in place.


... Tristar Vacuums

Bissell Healthy Home Vacuum brush stopped working. The hose attachment works fine, just the brush on bottom. Without taking it completely apart, it shows no sign of blockage. Any suggestions? Or, will I have to take it apart?


You will have to remove the bottom plate to get at the brush. The drive belt either slipped off or broke, this will have to be replaced. ... Vacuums

Shopvac 90L400 quit working (4 years old). Thought the switch was bad but not the problem. I read that there is a fuse link in the motor that frequently burns up. I tried to take motor apart but not sure of the process. I was able to get to the motor but cannot pull it out of the armature. It appears I have to take the aluminum blower unit off the shaft (it appears to be pressed on with a retaining washer). Do I have to take it off to pull the shaft and motor assembly out? Is that where the fuse


By pass the switch and take power right to the motor leads.. that should tell you if the motor is ok.. have not seen fuse link on a vac motor.. graingers has new motors, but not inexpensive ... Vacuums

How do I take apart my Bissell 7920 ProHeat Pro-Tech


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Will not steam. before taking apart is there a


Hi,Look at the manual...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...E ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

We had to take the machine apart just to see that the belt had broken after only 5 use's . We can not see how we are ever going to put the new belt back on. do you have instructions on how to take the belt off and how to put a new one on? Please send me one.


I have a Panasonic MC-V5746 upright vacuum. According to the booklet, \015\012MAKE SURE UNIT IS UNPLUGGED.\015\0121. Place carpet-bare floor selector in "carpet" position.\015\0122. Remove lower plate (there are two screws in the m ... Vacuums

Changing belt How do I do that? It looks like I would have to take the screwdriver to the bottom and enter the engine compartment. I'm not sure that I feel confident to take this machine all apart and be able to get it back together again.


Its not the engine compatment take the screws out the cover 4 the roller will come off then u can c where the belt goes ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

HOW DO WE TAKE apart THE BATTERY APART ON THE Shark cordless stikVac


Try this linkhttp://www.sharkclean.com/manual/SV1100_ENG_110916_4.pdf ... Shark Cordless Stikvac Vacuum Cleaner sv800

I need to know how (if) I can take apart a Miele electric telescoping wand apart to clear some debris from it. Thanks!


Take a close hanger, Or a stick end push it though to clean it out. ... Vacuums

A baby sock was sucked up and stuck where i can't see it in my regina electrikbroom cleaner - 11.4 amp. i have tried to get it out and now i have to take it apart i think and can't get the housing apart - what should i do?


... Regina ElectrikBroom RG100 Vacuum

How do i take apart the dyson,Theyre is something stuck in the hose extension. Is theyre anyway to take it off. The bottom part works . however theyre is no scution threw the hose


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

How do you take apart a electrolux epic 3500 to take out the circut breacker


... Electrolux Epic 3500 Vacuum

Can you take the Swivel Sweeper battery pack apart to replace the batteries with new rechargeable batteries? Batteries look like AA or AAA, but it appears that the battery pack is sealed. Is there any way to get it apart:?


Yes you can if you have a way to cut through the plastic outer case,(I used a Dremel rotary tool). Inside you will find six double A Ni-mh batteries. I found eight of these for sale on ebay for around ten bucks,then all you do is solder some wire to ... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

I take apart and clean my DC17 every 2 weeks. When I put it back together it always works perfect. This last time, I noticed that the self propel is not working...am I missing something? I took it apart to be sure eveything is in it's place but no difference. Now I have to push really hard.Any suggestions?


The roller is not spinning do to motor or belt not working. If it is the motor then the machine will have to go back to dyson if it is the belt then that is an easy replacement. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hoover F5809 Hello, I seen a few of your post and was hoping you could help me. I just became a member today. My sister gave me her old Hoover Steam Vac-Model F5809. This thing is so dirty and clogged because my sister has pets. So far I've gotten it all taken apart to clean it. I'm not a newbie and taking apart and fixing things. I have fixed things like microwaves, washers, dryers, dishwashers (still learning about TV's-very hard, hehe). Anyway, I got what I believe to be the motor cover off.


That cover is the called the fan cover and is usually pressed on. Tapping on the edge with a flat blade, you may be able to get it off and hope you don't bend it up, you will to put it back on tight enough so it will stay in place. Another thing to ... Vacuums

I am trying to take my philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag was not put in correctly. I have removed all visible screws but cannot for the life of me find how the wheel end comes apart. any tips?


Generic problem for all Vacuums\015\012I am trying to take\015\012I am trying to take my Philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0253 seconds