Having problems with your Beam Industries 2775 Serenity Plus Central System Vacuum ?

No suction beam serenity plus

\015 Stopped working. at unit, bag is clear. light exhaust from 1 muffler, 0 from other. reduced suction from inlet at unit. HELP> thx\015

Answers :

You are right-on. turns out 1`) the pockets holding weights in bag had opened up. 2) no exhaust from 1 muffler indicated dead motor. sending back to factory thru installer. are there local repair places in nashville tn for future reference?
\015\012
\015\012thanks
You may need a new filter bag part #110346. They can cause suction problems at the unit. Either that are there is a problem with the motor, does it sound alright when running? If not, take it to a beam repair shop, with proof of purchase, the motor would be under warranty for the part only, not labor. The filter bag is not covered by warranty.
Repair Help & Product Troubleshooting for Beam Industries 2775 Serenity Plus Central System Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No suction beam serenity plus


You are right-on. turns out 1`) the pockets holding weights in bag had opened up. 2) no exhaust from 1 muffler indicated dead motor. sending back to factory thru installer. are there local repair places in nashville tn for future reference? ... Beam Industries 2775 Serenity Plus Central System Vacuum

Beam Serenity Plus doesn't ****


If its obserdly loud its a bag motor not a clog. ... Beam Industries 2775 Serenity Plus Central System Vacuum

How to remove filter on beam model 2775 - Beam Industries 2775 Serenity Plus Central System Vacuum


Remove the bucket and look up inside the tank. There will be a finger loop to help pull the filter from it's track. You can shake it clean by wrapping a garbage bag around the tank, squeezing the air from the bag ( so it doesn't puff dust back at you ... Beam Industries 2775 Serenity Plus Central System Vacuum

BEAM Serenity Plus 2900 has shutdown


I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. OK, there is a reset button on the unit but i think it could be that your vacuum could be clogged in the vacuum lines and that you should check all ... Beam Industries 2900 Serenity Plus Central System Vacuum

We have a beam Serenity plus home vacuum system and there is no longer sucks. I removed the dirt from the bottom plastic container, but I also notice a sack or bag connected to the unit when I removed the bottom container and inside that sack there appears to be lots of dust. How do I access that and remove that dust without damaging the unit. I don't know how to do that


Hello. Let's begin by getting that dust and dirt out of your permanent filter. To do this, get a big clear plastic bag and pull it up aroung your canister, with the dirt receptacle removed. Then Grasp the sewn in weight inside of the filter and sh ... Beam Industries 2900 Serenity Plus Central System Vacuum

My Beam Serenity BM1383 vacuum cleaner is blowing dog hairs and dust back even after checking for a blockage in the hose, a leak in the hose, suction at all outlets, and changing the belt. Do the bristles on the roller wear down after time?


... Beam Industries Wet/Dry Auto Central System Vacuum

Beam serenity plus is tripping the breaker switch


... Beam Industries 2775 Serenity Plus Central System Vacuum

Need the manual, do you have it? - Beam Industries 2775 Serenity Plus Central System Vacuum


Go this this website: http://www.beamvac.com/usa/support/manuals.aspx ... Beam Industries 2775 Serenity Plus Central System Vacuum

Beam Serenity Plus Powerbrush Quick Release SP800


... Beam Serenity Plus Powerbrush Quick Release SP800

Small fire at the hose and wand connection of beam serenity plus


... Beam Industries 2775 Serenity Plus Central System Vacuum

Vacuum low sucking power - Beam Industries 2775 Serenity Plus Central System Vacuum


... Beam Industries 2775 Serenity Plus Central System Vacuum

My beam serenity plus power head shuts off as soon as it hits our carpet. It runs when held off the floor though. Do you know what could be causing this? The only thing that starts it up is the red reset button.


... Beam Industries 2900 Serenity Plus Central System Vacuum

Need owner's manual for beam serenity plus 2775


Download manual here > http://www.beamvac.com/usa/support/manuals.aspx ... Beam Industries 2775 Serenity Plus Central System Vacuum

Where can i get a new flexible tube? - Beam Industries 2775 Serenity Plus Central System Vacuum


... Beam Industries 2775 Serenity Plus Central System Vacuum

My beater head will not turn on - Beam Industries 2775 Serenity Plus Central System Vacuum


If you could wire the beater head with out using the hose you could determine if the short is in the hose or in the head. If you wire the head directly and it turns on obviously you have a short in the hose. It is possible to change just the switch a ... Beam Industries 2775 Serenity Plus Central System Vacuum

How do I remove the canister ? - Beam Industries 2775 Serenity Plus Central System Vacuum


Grab hold of the two grips on the left and right, left is towards the back and right is towards the front. you will be twisting the pail (right side) from the standard 3oclock position to the 5 oclock position there. the cannister should just fall of ... Beam Industries 2775 Serenity Plus Central System Vacuum

I have a Beam serenity plus SP800A vacuum, the red light went on and the bristles stopped turning when I vacuumed up my bathroom rug. what does the reset button look like. Or does this model have a reset button. how do I turn off the red light so that the bristles start turning again?


... Beam Industries 2775 Serenity Plus Central System Vacuum

System quit working green light on - Beam Industries 2775 Serenity Plus Central System Vacuum


Depending on the year of your machine, assuming it is the serenity blue, it may be the circuit board on the unit itself. The manual switch "should" start the machine, but if not it will be the circuit board inside the main unit. however.. ... Beam Industries 2775 Serenity Plus Central System Vacuum

Hoover SteamVac Plus 1200 upright hot water extractor Water/carpet cleaner applying o.k. Suction on the "floor" does not work. Suction on the hand tool works somewhat, but water is not collecting in the bucket. There is suction coming from the floor but water is not going into the bucket. It does not appear to be clogged because I can feel with my hand that air is flowing from the floor. The water is not being sucked into the bucket.


... Hoover Vacuums

Can't remove the dust bucket on a Beam Serenity vacuum cleaner


Did you ever get an answer. I also cannot get the bucket off. ... Beam Industries 2775 Serenity Plus Central System Vacuum

No suction in the walls for our Beam Heavy Duty Vacuum.


Do you have any open valves? Sometimes when vacpans are installed they are left open. Check those and then the other inlets to make sure they are not open.\015\012\015\012Also, if this unit is not newly installed, then you need to check f ... Vacuums

We have a beam built in vacumn system ( old one) there is virtually no suction coming through the hose. I suspect some sunflower seeds were picked up and clogging it somewhere. What to do?


You need to figure out if it is the hose that is clogged, or in the piping. If in the hose, you can use a long plumbers snake to try to remove the clog. If you have no suction in none of the outlets, then I would suspect the hose, or the main pipe ... Vacuums

I have a one year old Beam central vac. It has supervalves. The handle (connected to the hose stopped turning on the unit. The handle still powers the brush but no longer turns on the suction?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=566201 ... Vacuums

I have a Kenmore Destiny Plus vacuum, and it doesn't have suction anymore. I've come to the conclusion that the tubes, I guess you can call them that, are plugged. I'm trying to find the user manual/service manual to know how to open the vacuum up to unplug the tubing.


It's October now so this is probably too late to be useful for you but it might help someone: I had the same problem. I used a bright light to see that there was a clog up high in one of the plastic tubes on the side. Using an untwisted wire coat han ... Kenmore Vacuums

I have a Hoover Fusion Plus. I rarely use it. Lately it does not have any suction HELP!!!


I failed to mention that I took the thing apart. I checked the hose and all intake areas. There is suction at the top, where the filter and tank assembly goes but it does not pull from the tank mechanism or the brush assembly. Man! So frustrating. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0365 seconds