Having problems with your Beam Industries 2775 Serenity Plus Central System Vacuum ?

I have no power to the roller motor but if I disconnect and connect direct power, at the hand connection, it works. Is there a fuse somewhere I do not know about. If not what is the problem and solution? Thanks, Wayne [email protected]


Answers :

If you have taken the handset and plugged directly to the head...you have already found your problem to be the hose.
\015\012
\015\012Either take the hose to local vacuum repair shop or test the continuity of the hose yourself.
\015\012
\015\012Problem is the hose.
\015\012
\015\012Mike...
Repair Help & Product Troubleshooting for Beam Industries 2775 Serenity Plus Central System Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have no power to the roller motor but if I disconnect and connect direct power, at the hand connection, it works. Is there a fuse somewhere I do not know about. If not what is the problem and solution? Thanks, Wayne [email protected]


If you have taken the handset and plugged directly to the head...you have already found your problem to be the hose.\015\012\015\012Either take the hose to local vacuum repair shop or test the continuity of the hose yourself. ... Beam Industries 2775 Serenity Plus Central System Vacuum

I have a Bissell Proheat Turbo 2x model 9300. It has stopped spraying at the floor. The hand tools will work so I assume this means the problem is at the base somewhere. I cleaned the nozzles but don't know what to try next. It has always had a problem with dumping too much cleaning solution as well, don't know if this is a contributing factor


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Hi, I have a Xenon 600 VA sinewave inverter. My inverter starts working even when the main power is ON.So the battery gets dried up even when power is there.Can I know why this is happening? Is this due to main power line problem or a inverter problem.


... Vacuums

Kirby Sentria I bought my kirby sentria just before we were to move house and although I have the instructions somewhere, they will be boxed up and I so want to clean the carpets before I move. Problem is that I don't know whether the belt should be on or off when using the big silver front with the Kirby insignia on it. I know that the green light should come on when it is working properly and it does not, so I am doing something wrong. I can attach the attachments no problem but I want to use


If the green light is off, then its time to replace the band. This video shows you how. ... Kirby Ultimate G Bagged Upright Vacuum

Dirt Devil M082475 12 AMP cannister vacuum power-head problem


Theres no fuse, you will need a new hose ... Bosch 12-Amp Formula Canister Vacuum with Hepa Filtration Bagged Vacuum

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.


I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Cleaning Solution It really isn't a mechanical problem. I would like to know what kind of solution I need to put into my machine. I bought it used and if didn't have a manual and I can't recall what I was told to put into the machine. I hope someone can answer my question. Thank you in advance Phyllis Woodall.


Most any brand name carpet cleaning solution will work. I like ZEP from the Home Depot. Nice fragrance, low foam and economical vs. Bissell, Hoover, other appliance brand names. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My e wave microwave appears to be in fine working order until the door is opened. It then trips the breaker and ceases working. Ater the house breaker is reset, the power is restored to the microwave until the door is opened again.. I havve tried plugging the microwave into another area that is on a different power breaker but again the breaker trips and the microwave ends all functions. Have you any solutions to my problem? Email Address [email protected]


You may have a short circuit on the INTERIOR LIGHT BULB circuit in your microwave.\015\012\015\012This might explain why the breaker trips every time you open the door.\015\012\015\012If so, you would have to unplug and disass ... Vacuums

My bissell power trak just stopped working i turned it off and a few hours later i turned it on again and it will not work. I switched over to an outlet i know works and it still didn't work I checked the outlet after and there's still power there. Is there an internal fuse?


... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

On several occasions the belt has come off the Hoover Windtunnel beater shaft and had to be re-installed. Is there any way to prevent it from slipping off? The shaft seems to be made so that the middle if it is wider(thicker than either the end or the part closer to the motor, which, to me, is a bad design so I don't know how to overcome this problem. I'd be very grateful for a permanent solution to this problem. Thanks in Advance, mas


Your belt is stretched and needs replacement ( # 38528035 ) . The agitator is crowned so that the belt stays centered. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

The microwave will not turn on. No power. Checked fuse box and power outlet...not the problem. Unit just wont turn on? Is there a reset button or another option.?


Remove the cover and locate the internal fuse you will find near the power cord entry. Replace with the same. ... Vacuums

Attachment problem used a new unit w/attachment for 5 minutes...dispensed solution in a powerful triangular fashion. Then the fluid quit dispensing out of the attachment nozle amost like the pump quit working. Primed the unit several times w/ no success. checked for clogs. can't tell if the floor portion is "pumping' or just dribbling solution onto the floor with the trigger. can see no leaks at this point. unit worked for about 5 minutes on apholstery


Make sure everything is filled and secured tightly, if this a new unit it should be something simple ok, also check where machine folds down that the solution hose is not being pinched its right behind the dirty water tank ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I was trying to repair my wife's kitchenaid mixer and took part of it apart, including the back part, where the electrical connections are. The original problem was the plastic gear was damaged -- I finally had the good sense to find the solution for that problem on the internet and replaced the damaged part. But now the mixer just won't turn on. I don't think I damaged anything in the electrical section, but I suspect I either blew a fuse or somehow disconnected something.


Do you have a model number? Is the voltage getting to the motor from the switch? ... Vacuums

The battery will not charge in the sweeper. I can remove the battery and wire it to the power supply for charging and it will charge up and run the sweeper. So the power supply and the battery are both good. Obviously there is a circuit failure in the on board charging control. Anyone know a fix or a likely faulty component? I had a shark handheld about 8 years ago and it developed the same problem. I examined the little circuit board inside but saw no visible indications that would isolate t


... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

I have a dyson DC28 vacuum and the power button flashes on and off and the beater bar quit turning. I turned it over and found some string caught on the beater bar which I removed, but the beater bar still does'nt turn and the power button still flashes on and off. I hope you can give me a solution to this problem.


I had the same symptom with my wife's DC28. The problem was associated with the cam driven height adjustment mechanism. The beater bar must rock freely up and down when pressing on the tabs that the end cam lobes actuate. On ours I found hair and cru ... Dyson DC28 Animal Bagless Upright Vacuum

I have been trying to register on line and can't get in. I am having problems with my WindTunnel powered nozzle it doesn't want to run and I just got this as a gift May 1st. The power hand tool works but not the other one and I know all the connectins are good


It will have a years warranty on it. Take it in to a warranty repair shop and tell them that yo got it as a gift and when. ... Vacuums

Electrolux LUX 7000 model - the power vac has stopped working - pushed reset - is there a fuse somewhere and/or how to you replace the on/off switch?


It could be that your motor has fried or the wires on the motor have come loose. ... Electrolux Lux 5500 Canister Vacuum

Not working I know it is pulling in , but when i turn it own it will not let the solution out. I cannot use it. one part is not in somewhere


I found resources for getting parts, at Ebay and here- http://www.buckeyevac.com/site/. Haven't used them but it looks promising. ... Bissell 1631 PowerSteamer ProHeat Canister Vacuum

110-220V Dear Sir, I purchased a kirby sentria vacuum cleaner from ebau two weeks ago. I currently resid in the UAE with 220V power. My maid has plugged the vacuum to work with it unaware of the voltage difference, a terrble noise as mentioned came from the cleaner as well as a smell. She unlugged it and stopped t from operating. Can you please let me know how can i assess the damage? If this model has a switch from 110 to 220V IS there a solution with transfromer or motor to make it work? Thank


You may have burnt up the motor field when it was plugged into a 220V power source. But there are drop down transformers you can get to reduce the voltage form 210 to 110. AS Radio Shack or similar store would have them. ... Kirby G4 Bagged Upright Vacuum

My roomba 530 runs in a circle and does not move forward. After 2 minutes it stops with 11 beeps and a flashing red light to the left of the power button. It has no clicking noise. Does anyone know what is the problem?


Hey'\015\012This means Roomba is not registering obstacles. Roomba may be stuck in one place.\015\012Roomba may be in extremely large room, try setting up virtual walls to create smaller area.If Roomb ... Roomba Robotic Floor Bagless Vacuum

I have use my henry with no problem, tunred it off with the red switch on the top, 20 minutes later I went to use again but the machoine was toatlly dead with no power I have changed the plug fuse


Could be fault @ plug.. try cutting off 10 mm of cable then redo plug ..Replace fuse then try, if still dead try switch, you could short this out or if you have multimeter check for contact...if stii no action could be motor.... ... Vacuums

When turned on caused, caused a pop at the outlet and don't know if the if the power cord went bad or short somewhere else in the sustem. what do i do and how


Hi, that pop sound you heard at the outlet simply implies that the fuse blew off. What you just need to do is too replace the fuse and if the power cord is having a burn smell, then i will also advise you to change the power cord..Take ca ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Hi all---I have a Dirt Devil 091020V. there was a problem with the wand where it was the only thing sucking even when it was stuck in the tube it would ****--but nothing from the vacuum end--the diverter was stuck closed I took it apart and found something stuck but in the meantime the torsion spring [I think} fell out and I don't know where it goes--so now only the vacuum works --not the overhead cleaner part.. is there a digram somewhere that can tell me where it goes--I think it might b


... Vacuums

I have a hayden premier supervac central vac system, while working on the switch in for the beater bar, the actual unit has turned off, the green light is no longer lit, is there a fuse on it somewhere or a reset button, i have tried unplugging it and replugging it in, but can not seem to get it to power up now?


Should be a reset on the main unit near the top ... Vacuums

Have a kenmore canister vacuum cleaner which the power-mate parts don't work. I had loaned the vac out it came back with part of the hose smashed. I don't know if that is the problem.


The hose conducts power to the "power Mate" There are wires running end to end through the hose and handle. If your hose is grey with hard plastic cuffs at both ends, it is repairable, but you will need to locate the Smashed parts. If yo ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0765 seconds