Having problems with your Beam Industries 2775 Serenity Plus Central System Vacuum ?

Motor won't turn on

\015 The green LED is on. The reset breaker is pushed in. I can hear the relay click when I short the leads on the unit and again when I break the circuit. It also clicks when a hose is inserted into one of the inlets. The manual switch does not make the motor turn on either. I hear no hum (presumably no frozen motor). The unit does not stink (no electrical short presumably). The cannister was half way full when I discovered it wasn't working.\015

Answers :

It sounds like you have a motor problem there. I don't know how old your machine is, but if it is still under warranty, don't explore any further as you will void your warranty. This problem sounds like a carbon brush problem and you will not be able to address it yourself unless you know your way around an electrical motor. The carbon brushes can stick or become jammed and once they are loosened up, they need to be reseated or the motor will burn out. You will not be able to do this yourself. These motors generally have 5 to 12 year warranties and yours may still be under warranty. If your machine is over 10 years old, the carbs are probably worn out and the motor will require repair or replacement. You should refer to a competent tech for help.
Repair Help & Product Troubleshooting for Beam Industries 2775 Serenity Plus Central System Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

DC 17 UPRIGHT BRUSH MOTOR WONT STAY RUNNING. TURN


Have a look at the filters first as it sounds like you blokeage ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Bissell lift off motor wont turn on.


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

VACCUUM GOES ON, MOTOR WORKS, BRUSH WONT TURN WHEN THE VACCUM IS TURNED ON.


Check the belt, and remove any objects clogged in the roller system ... Dyson Vacuums

Motor wont turn on.I checked the switch and I think it is working.motor turns on if a put direct power to it.'but it smokes at the brushes. can you help?


This sounds like either the belt isn`t on right or the brush is not slotted in the vacuum right remove the plastic or metal cover from the bottom and check by inspecting the belts ability to easly turn the brush rod check with your hands DO NOT turn ... Kirby G4 Bagged Upright Vacuum

Roller brush won't turn...the motor runs but wont turn..acts like it is seized up..


The belt may have come of or broke..\015\012Turn the vac over so the bottom is facing up..\015\012Remove the scews in the plate cover that surrunds the brush..\015\012Remove the plate cover..\015\012You will see if the belt is ... Vacuums

Power cord worn out where it enters motor, have to move cord certain direction and will turn on. Cord finally gave out one day and almost shocked me when it literally blew out. wont turn back on


You have popped the fuse in the plug top or have burnt out the wires in the cable \015\012\015\012No matter you have got to shorten and re-wire the cable into the cleaner or get a new lenght of flex and do the same thing.\015\012 ... Filter Queen Majestic Canister Vacuum

Roller motor on a DC17 dyson wont turn on


There is a reset button under the cover that houses the on/off switches. remove the handle/wand and look on the back (where the top of the hose sits) for 2 screws (its a torx/star head screw size t10 i believe). remove them and locate 4 small locki ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Motor shaft wont turn on EL2050 - Electrolux Central Vacuum


Have you tried running the brush motor without a belt on it? Does it not spin without the belt? If so, you may have worn motor brushes (not too expensive parts, but make sure you order both brushes, or make sure they are sold as a set). If your motor ... Electrolux Central Vacuum

My dyson dc07 wont turn on. is there a motor reset button on the dyson dc07


No it does not have a reset button av you checked the fuse in wall plug if OK it's most likely the switch as gone bad here is a video how to replace ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Caught rug, motor overheated, the brush wont turn at all, but suction is still there ...is there something I can do to reset it?


Assume that the belt is broken to the power brush /head. Did you happen to smell burning rubber at all when the motor got stuck? The motor may have a reset on it, if it was not operating, but that is not the case, as mentioned. Look in your manual fo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Vac motor runs but belt wont turn - Eureka Power Plus 4703D Bagless Upright Vacuum


Its time to check and/or change your belt. to do this you want to remove the two screws on the top casing and remove the cover. There are detailed belt change instructions on a sticker under the top casing on how to remove the brush and b ... Eureka Power Plus 4703D Bagless Upright Vacuum

My Kirby G 2001 upright vacuum wont turn on. I tried another outlet and still nothing. I don't see a breaker switch anywhere. If you know of any common problems I would love to hear them. I am very mechanically inclined, I just was wondering if there are any common issues with the motors or power switches etc. so I don't waste a lot of time troubleshooting. Thanks


This might sound a bit silly but check to see if the cord is plugged into the machine correctly if it is check to see if the safety interlocks are all engaged. ... Vacuums

I have an open in the black wire leading down to the carpet sweeper (after the handle), thus the motor wont turn on. how do i get to the wiring to re-run a black wire?


Did you test the wire with the switch in the "ON" position. If not, try it before opening the handle. \015\012The problem is more likely to be a worn out or broken switch, including a reset switch.\015\012Also try connecting the hose di ... Kenmore 28015 Bagged Canister Vacuum

Dyson dc04 wont pick up,motor working,replaced clutch assembly but still dosnt turn brushes


You need to go through a process of elimination. You are better doing that here: Dyson advice forums ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Broken belt, motor wont turn - Vacuums


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=721048\015\012Generic problem for all Vacuums\015\012Broken belt, motor won’t turn\015\012Posted ... Vacuums

The bar that the belt sits on wont spin and smells like its burning when you turn it on. Is the motor out?


Hi,No, it is not the motor, it is a bad belt or something is jammed causing the belt to slip...\012Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Wont turn on - Plug is hot - is there a reset on the motor


If plug is hot, it isn't making good contact with the socket it is plugged into. Try to turn the fan to see if the motor has seized. If so, might be bad motor bearing, or large amount of vacuumed dirt accumulated. Should be a reset, but not sure wher ... Dyson DC07 Full Gear Bagless Upright Cyclonic Vacuum

Dewalt 2gallon corded/cordless vacume...unsed one time brand new wont turn on. motor and switch both tested and work...any ideas


Check the battery contacts... a common problem on this model. they are easily bent and prone to corrosion. ... Dewalt Cordless/Corded Wet/Dry Vac 2 Gallon Vacuum

Brush roller wont turn, motor is good and the curcuit board appears fine. No evidence of anything blown or broken wires either.


Judging from this parts diagram:\012http://www. ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther


... Clarke Vacuums

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t


... Vacuums

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan


Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

I was vacuuming the vent in the bottom of the fridge. I must have picked something because the motor got wildly noisey. I cleaned out hoses, etc. There is no suction. I can see the blades of the motor and they are not turning around. Model U4269-930 Series B.72. Can I get at the motor to see if something is keeping the blades from turning? What would be your suggestion. Many thanks. Pat Sauerman


Hi Pat, my name is John I will do my best to assist you.\015\012\015\012You certainly can get at the motor, with simple hand tools. \015\012\015\012Referring to this ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1340 seconds