Having problems with your Beam Industries 2775 Serenity Plus Central System Vacuum ?

System quit working green light on - Beam Industries 2775 Serenity Plus Central System Vacuum


Answers :

Depending on the year of your machine, assuming it is the serenity blue, it may be the circuit board on the unit itself. The manual switch "should" start the machine, but if not it will be the circuit board inside the main unit.

however....
if your unit is the green one, it may be the motor inside the unit and/or the circuit board. Hard to say. I do not think that it is the motor as the circuit breaker should have popped out if it was the motor.

Regardless of the colour of the unit, if it is 5-7 years old or less, the unit should still be under warranty. home service calls and labour to install the motor would not be covered.

Good luck.
The motor is shot , Junk the unit, the new Beam models have way better performance than ever before, Slow starting hi performance motor with silencing system to make it quieter than ever.Simply amazing performance.
Repair Help & Product Troubleshooting for Beam Industries 2775 Serenity Plus Central System Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

System quit working green light on - Beam Industries 2775 Serenity Plus Central System Vacuum


Depending on the year of your machine, assuming it is the serenity blue, it may be the circuit board on the unit itself. The manual switch "should" start the machine, but if not it will be the circuit board inside the main unit. however.. ... Beam Industries 2775 Serenity Plus Central System Vacuum

How to remove filter on beam model 2775 - Beam Industries 2775 Serenity Plus Central System Vacuum


Remove the bucket and look up inside the tank. There will be a finger loop to help pull the filter from it's track. You can shake it clean by wrapping a garbage bag around the tank, squeezing the air from the bag ( so it doesn't puff dust back at you ... Beam Industries 2775 Serenity Plus Central System Vacuum

Vacuum low sucking power - Beam Industries 2775 Serenity Plus Central System Vacuum


... Beam Industries 2775 Serenity Plus Central System Vacuum

Need the manual, do you have it? - Beam Industries 2775 Serenity Plus Central System Vacuum


Go this this website: http://www.beamvac.com/usa/support/manuals.aspx ... Beam Industries 2775 Serenity Plus Central System Vacuum

My beater head will not turn on - Beam Industries 2775 Serenity Plus Central System Vacuum


If you could wire the beater head with out using the hose you could determine if the short is in the hose or in the head. If you wire the head directly and it turns on obviously you have a short in the hose. It is possible to change just the switch a ... Beam Industries 2775 Serenity Plus Central System Vacuum

How do I remove the canister ? - Beam Industries 2775 Serenity Plus Central System Vacuum


Grab hold of the two grips on the left and right, left is towards the back and right is towards the front. you will be twisting the pail (right side) from the standard 3oclock position to the 5 oclock position there. the cannister should just fall of ... Beam Industries 2775 Serenity Plus Central System Vacuum

Where can i get a new flexible tube? - Beam Industries 2775 Serenity Plus Central System Vacuum


... Beam Industries 2775 Serenity Plus Central System Vacuum

Beam central vacuum system just stopped working


... Vacuums

Beam central vacuum system


... Vacuums

We have a beam Serenity plus home vacuum system and there is no longer sucks. I removed the dirt from the bottom plastic container, but I also notice a sack or bag connected to the unit when I removed the bottom container and inside that sack there appears to be lots of dust. How do I access that and remove that dust without damaging the unit. I don't know how to do that


Hello. Let's begin by getting that dust and dirt out of your permanent filter. To do this, get a big clear plastic bag and pull it up aroung your canister, with the dirt receptacle removed. Then Grasp the sewn in weight inside of the filter and sh ... Beam Industries 2900 Serenity Plus Central System Vacuum

My home has a central vacuum system hook-up but no vacuum installed. My friend upgraded his central system and gave me his Eureka Mega Boss central vacuum system and the accessories, including the pow


The power head requires 120 Volts. Some hoses have a receptacle in the handle for the power head plug, and the hose has a cord at the wall inlet end that plugs into a receptacle. Some hoses have a plug at the wall inlet end that plugs into a 120Volt ... Eureka 1810 Central System Vacuum

Changed the motor carbon brushes on my Beam central vacuum cleaner equiped with an IntelliWatch system. This system includes the Alutron DB100 module. This Alutron module needs to be reset so that the vacuum cleaner can operate properly. I believe that this module keeps log of running time and disables operation after a predetermined time. Can you help me with providing a reset procedure that will reset this module. Thanks


... Sunbeam Vacuums

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?


Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

I have central system vacuum cylinder engine is working but on the wall conection nothing is working.


Check to see if the low voltage wires are attached to the tank. At the tank, if you switch it to manuak, will it work then? If so, then replace the relay board that is inside the tank. Is the problem at all outlets, or just one of them, if just on ... Hoover Vacuums

I have a Beam serenity plus SP800A vacuum, the red light went on and the bristles stopped turning when I vacuumed up my bathroom rug. what does the reset button look like. Or does this model have a reset button. how do I turn off the red light so that the bristles start turning again?


... Beam Industries 2775 Serenity Plus Central System Vacuum

I have a 10 year old AirVac central vacuum system that has worked until this morning. As I was using it this morning, and turned it off for about five minutes it would not start again. The tank in the garage (that accepts the dust) sounds like it is just huming not working. What is wrong?


Sounds like the motor finally siezed on you. Motor is trying to turn but won't thus the hum. Do not allow the vacuum to stay on like this as it may cause a fire. Requires a motor replacement. ... M&S Systems ZX7000 Bagged Central System Vacuum

While vacuuming with a beam central vacuum system it suddenly just lost power and suction.


... Beam Industries 875 Classic Central System Vacuum

I have a Kenmore Central Vacuum Type K Model s107. The system will not work with the short handle, therefore I can not use the adapter brush ect. It will work when it is connected to the long handled main attacment. Any suggestions on how to fix this problem?


... Kenmore Vacuums

I have a coleman mach central system that works of of my generator, but not shore power, ther is 120 volts at the plug. the green light on control panel flashes 4 times break, and 4 more times . The


1) test the power cord for break or ope2)see if the c.breaker are tripped or blown fuse3) see the vacuum has reset switch do it4) Power button defective or open 5) switch inside defective or open repair or replace6) Motor defectiv ... Vacuums

Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would


... Hoover L2310 GUV Central System Vacuum

Where are the fuses located on a q100 - Beam Industries Wet/Dry Auto Central System Vacuum


Go here> http://www.beamvac.com/usa/support/manuals.aspx for help ... Beam Industries Wet/Dry Auto Central System Vacuum

Green light blinking - Hayden Industries SuperVac 3600 Central System Vacuum


... Hayden Industries SuperVac 3600 Central System Vacuum

I need an operational manual for a beam central vac model 178. It came with the house and I need to take it apart and clean it. Does the filter thing inside the system come off. It is caked in dust and dirt and I think it is effecting the performance of the vacuum.


... Vacuums

Kenmore Central Vacuum System-electrical o.k. but suction function not working. No noise from canister.


It could even be a bad motor if its an old kenmore system. If its more than 10 years old it maybe worth getting a whole new tank over just a motor. ... Vacuums

How to repair BEAM Central Vacuum Power Brush. Motor works perfectly, belt brand new but unable to spin brush.


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1658 seconds