Having problems with your Beam Industries 2900 Serenity Plus Central System Vacuum ?

We have a beam Serenity plus home vacuum system and there is no longer sucks. I removed the dirt from the bottom plastic container, but I also notice a sack or bag connected to the unit when I removed the bottom container and inside that sack there appears to be lots of dust. How do I access that and remove that dust without damaging the unit. I don't know how to do that


Answers :

Hello. Let's begin by getting that dust and dirt out of your permanent filter. To do this, get a big clear plastic bag and pull it up aroung your canister, with the dirt receptacle removed. Then Grasp the sewn in weight inside of the filter and shake it around. This will cause the dust to come into the plastic bag. Continue to do this until most of the dust has left the filter and made it's way into the plastic bag. THEN
\015\012
\015\0121. Put the empty bottom plastic container back in place as hopefully now, and turn the unit on using the manual switch on the side of the unit. Let it run for ten minutes.
\015\012
\015\012This may solve the problem but if the system is still clogged read on:
\015\0121. Replace the empty dirt receptacle and use the manual switch on the side of the unit to start the unit. Leave it running as you continue.
\015\012
\015\0122. Then start at the closest wall balce to the unit and open the door to the wall valve. Then let a tissue be sucked from your hand. If the tissue makes it back to the dirt receptacle proceed to the next wall valve.
\015\012
\015\0123. IF at any valve, the tissue fails to go through to the dirt receptacle, there might be a blockage of some degree. At this point, use a shop vac or at least another strong vacuum cleaner to try to use back suction to uncolg the blockage.
\015\012
\015\0124. If that fails, you will have to snake the pipe, a dry garden hose works well for this purpose.
\015\012
\015\012Enjoy your working system and be sure to empty the dirt receptacle on a regular basis so the filter doesn't get filled again. Regards, Joe
Repair Help & Product Troubleshooting for Beam Industries 2900 Serenity Plus Central System Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a beam Serenity plus home vacuum system and there is no longer sucks. I removed the dirt from the bottom plastic container, but I also notice a sack or bag connected to the unit when I removed the bottom container and inside that sack there appears to be lots of dust. How do I access that and remove that dust without damaging the unit. I don't know how to do that


Hello. Let's begin by getting that dust and dirt out of your permanent filter. To do this, get a big clear plastic bag and pull it up aroung your canister, with the dirt receptacle removed. Then Grasp the sewn in weight inside of the filter and sh ... Beam Industries 2900 Serenity Plus Central System Vacuum

I need to know how to remove the dirt container on the eureka bagless vacuum. It says that it is easy to remove, yet we cant figure it out. is there some trick to it that we dont know?


There is a lever at the bottom of the dirt cup,turn it to the left and pull out the dirt cup.note while you have the dirt cup out make sure you clean all the filters there is one right above the dirt cup pull out on the right side and there is a filt ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Hello, my names Travis. I was contacting you in concern of my Kenmore Quick Clean 12AMP Vacum Cleaner. My girlfriend took the bottom off the vacum and removed the belt because the vacum wasnt picking up. I know have a new belt i just dont know where to put it on the vacum to reinstall it


Look for grooves on the motor shaft and on the brush shaft. ... Kenmore Quick Clean 30012 Vacuum

Hi I have a eureka 410 series lightweight upright and I took it apart to clean the dust from inside and on the very bottom of the handle the is a metal clip and a white straight plastic peice that fell out and I dont know how it goes back in.


... Eureka Whirlwind 410 Bagless Upright Cyclonic Vacuum

On the DC07, the entire cyclone assembly must be removed to empty the dust, debris, etc. collected when vacuuming. On the top of the cyclone is a "trigger" that you lift with your finger to release the bottom catch, which allows a clear flap to open on the "clear bin," thus letting all the debris fall out. My problem is when you lift the finger trigger, it does not release the catch on the bottom. Since the catch won't release, I cannot remove the entire clear bin either from the cyclone.Any sug


Beofre you go to the extent of buying a replacement canister, you can remove the top and using a straightened coat hanger type thing open that bottom lid. Then maybe you can clean the rim and possibly add some silicone spry to loosen things up. Here' ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a signature 2000 ac window unit (10,000 BTU). Recently, water begin to slowly drip from the bottom right of the unit. I heard it hitting my floor. I took the front panel off and saw water build up. The unit is mounted in the window perfectly. How do I remove the water? I live on the 2nd story of my apartment building.


... Vacuums

I have a Kirby Heritage 84. Great condition except the part that connects the innerbag is missing. I don't even know what it is called. I can open the vacuum cleaner bottom and see that the part is missing. It should be oval where it connects to the vacuum and then extend into the cloth bag. PLEASE HELP!


The Heritage 84 had two different bag assemblies available. One is a dump-out bag. The dirt simply dumps through the bottom. The other is the bagged style which has a full length zipper to open it. Inside it should contain a "bag fill tube", and a to ... Kirby Heritage II Vacuum

My Dyson vacuum works fine for cleaning the rug but the hose doesnt get any suction at all. I removed the hose and all the parts around it that I could and dont see any clogs or broken pieces. I lost my manual so I dont know if this is addressed, or if there is a switch Im not flipping. Gave it a thorough look but found nothing.


Hi there,Sorry to hear you're having a problem with your DC07. If you have suction through the cleaner head but not through the wand, it sounds as though you have a blockage. Although you say you've already checked for these, you may find ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Somehow I have endd up with a cannister type vacuum cleaner and all I know about it is that it says model:VC-H3301. All I need to know is how to open the container full of dust and dirt o I can empty it. Can someone help?


Here is some info on that vacuum that may help you. it tells who sold it and what brand and where to get filters.\015\012\015\012http://www.fixed4fr ... Vacuums

Doesn't work Our home was built and finished in August 07.  The central vac doesn't work.  There is supposed to be a slot that opens in the kitchen where you sweep the dust and it sucks it up.  Also, the mounted unit on the garage wall has a hose that goes up into the house but there is a hole open at the bottom of the unit.  Where can I get someone to help us?  Or, is there an installation manual I can download to see if the builder did it properly.  He stole our solar heater for our pool and s


Has the slot in the kitchen (VacPan) been installed? Or is it just not working? There should be tubing coming into the unit in the garage, and possibly another piece to exhaust the unit to the outdoors, although this isn't always necessary. The intak ... Electrolux Centralux Vacuum

Can you remove the plastic part on the bottom of the bag or to tighten or is that a crack I see dust blows out of the bottom


There is a hand grip built into the bottom of the housing to help remove it. If it has not been removed on a regular basis to dump out heavy debris, it may be stuck. Use a screwdriver as a lever and pry it outward from the motor unit to remove it and ... Kirby Ultimate G Bagged Upright Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Dirt is coming out the bottom of my Kenmore Progressive Upright Vacuum. My husband found a large dust bunny in the drive belt and removed it. He also changed the bag. Why is dirt coming out the bottom? Thanks.


Its still clogged, you gotta dig deeper ... Vacuums

Eureka Altima. Dust bin will not pull off for emptying. slide the lever sideways, and dust bin will not pull out. Has two tabs on the bottom. Appears may have the wrong part on this unit.


... Vacuums

On the bottom of the Fantom Fury where it states:"The United States and Canada utility patent....". Now go to the far right end of this statement (the end opposite the spring, well I have a crack in the plastic which, when toggled, moves the entire plastic underside of the vacuum to move. In other words, I think I need an entire bottom plastic plate. The cracked area also makes the foot lever (which lowers or locks the vacuum handle) not work as the crack makes it impossible to work. I know


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=545424\015\012Generic problem for all Vacuums\015\012On the bottom of the\015\012Posted by c ... Vacuums

We have A "WC1000" 12 cup Coffee maker. It is leaking water out the bottom of the unit. We have removed the bottom metal plate, but there is nothing in that area requiring attention.


I think a gasket may have melted, or is leaking. Also check the ends of the little hoses. they may have cracked. ... Vacuums

Eureka 4D. Brush turns but not alot of suction. dust bunnies build up inside the hose at the bottom and at the dust brush connection. Seems to be very hot. ?????


Try cleaning the filters ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

The little movable fin on the bottom of the removable collection fin broke off when I was removing the fin from the unit to clean the IONIC BREEZE QUANDRA AIR PURIFYER.


... Vacuums

I need to know about how to connect end part into the bottom


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Shop vac quiet plus series 8 gal 2.5hp blows all small particals and dust out the back vents, dont know if installing filters correctly?


... Shop Vac Vacuums

My hoover windtunnel u6323-930 has dust leaking into air when unit is on. i think it is in the housing I cannot see and I need ti know how to take apart to determine which part i need to order thanks David Macali


You will just have to start taking the base aprt until you can get the motor, Just remember how it was so you can put it back together correctly again. When you have the motor off, look at the fan chamber, you probably have a crack or hole in it. ... Hoover Vacuums

Dont know how to remove filter from my typhoon vc9430s-6 hoover???


... Typhoon Castex Wet/Dry Vacuum 608688 Vacuum

The vacuum turns on but wont run smells like burning rubber I took the bottom off and the belts dont appear to be broken but the one connected to beater bar seems like it may be loose


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=542493\015\012Generic problem for all Vacuums\015\012The vacuum turns on but\015\012Posted by mmetcalf on Apr 24 ... Vacuums

I have a Bissell 7920 ProHeat and only used it 4 times and the brush on the bottom has stopped spinning and when attempting to spray solution the flow indicator doesn't spin and nothing comes out. I have looked at all of the belts and they seem fine. I have also removed and cleaned the heating unit. Still nothing. Any other ideas?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0629 seconds