Having problems with your Beam Industries 750 Classic Bagless Central System Cyclonic Vacuum ?

My central vac has a clog in the pipes, whats the best way to clear it?


Answers :

Here is a good resource to help you:

How to unclog a central vacuum
Repair Help & Product Troubleshooting for Beam Industries 750 Classic Bagless Central System Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My central vac has a clog in the pipes, whats the best way to clear it?


Here is a good resource to help you:How to unclog a central vacuum ... Beam Industries 750 Classic Bagless Central System Cyclonic Vacuum

Good Evening, What is the best way to find and clear an obstacle in the piping of a Broan Central Vacuum system?


Here is a good resource:How to unclog a Central Vacuum System ... Vacuums

Low suction I have an Electrolux central vac that is approx. 11 yrs old. the suction is very low. this started about 1 week ago. I checked the hose and it is clear. I also went into the attic and checked the pipes(as far as I could see them) and they appeared to be intact.


1) Have you checked the filter? If it is clogged your suction will be low. Also, you could have a pipe loose where you can't see. Make sure that you can get a coin to go all the way through the hose. make sure the suction motor ( the unit ) is coming ... Electrolux Central Vacuum

Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would


... Hoover L2310 GUV Central System Vacuum

What's the best way to clear Clogged up intake tube?


The best way to clear the hose is to use a wire coat hanger to fish out the debris ( bend the wire straight and then bend a small hook in one end ).\015\012also make sure you remove the floor plate and fish out that hose area.\015\012 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How do I access the motor to my eureka capture? It has no suction at all but turns on just fine..filters are cleaned and there are no clogs or leaks on the hose....im thinking there must be something stuck in the motor possibly but there are soo many screws that im having trouble removing them all....whats the best way to access the motor to check it??


... Eureka Capture Upright Vacuum Vacuum

Central vac pipe stuffed with pine needles from XMAS!


You can use a Tornado Cloth to clean out your central vacuum piping.\015\012Its the simplest and most cost-effective maintenance routine you can\015\012do. \015\012\015\012You can purchase them from here\015\012\015\012http:// ... M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth


When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

No suction I am getting no suction on my central vac at the vac. I do not believe that the piping is plugged up, the vacuum is not creating suction. What are the causes of no suction at the vacuum and how do I take the top half of the Nutone central vac off?


Use the guide at builtinvacuum.com/flowchrt.html to find the issue and solution. Most likely you need to test it without any filter and be sure the bottom of the unit is attached :) To get access to the motors you need to unbolt the very top sides. ... Broan-NuTone CV350 Performance Bagged Central System Vacuum

How to unclog central vac pipe - M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum


... M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum

Can the two inlet pipes be connected to one line? The central vacuum I have is probably from 1993/4. It has one exhaust pipe and two inlet pipes. It was initially under my stairs. I would like to move it and have in fact moved it to the garage but am now fitting the pipes. I would like to join the two pipes that were previously going to the two inlets into one pipe. Can I do it? Also would I then join the wires? Would I put a plate on the other inlet? THANKS. It is a SMART president's choice vac


There is no real reason why not...As long as you have enough "****" then that should be fine, you will need to "Y" join and NOT a "****" joint. ... Vacuums

How do you clear a clog out of the wand? There has to be a way to remove the clog without damaging the hose.


I would push a length of stiff wire through to ease out the blockage.pete ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Bissel ProHeat carpet shampooer is not spraying to the floor. I have checked the hoses best I can and they appear to be clear, no clogs. The nozzles don't looked clogged either. The above floor hose does spray water. I definitely have not gotten my money's worth from this machine. Any solutions?


... Bissell 9200 Upright Vacuum

I have an electrolux central vacuum in my house. My central vac hose has something stuck in it, I think, maybe a sock. I tried to put a long dryer wand down it but the hose is just too long. Does this need a repair man or new hose?? Any idea of a way to blow it out? Thanks.


The best way to clear an obstruction is to blow it out by attaching the wall end to the exhaust of a shop vacuum, or using an air compressor.\015\012You can try holding the wand end of the hose directly to the CV in port and turning the machine ... Electrolux Central Vacuum

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I


You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

Hoover Steam Vac ; The vac is not dispensing cleaner/water. I suspect the tubing/path from tank holding the cleaner/water mixture is clogged. Is there an easy way to unclogg it. Are there are sketches/drawings showing the path and where it is is the machine.


Hi there,Just a quick clarification please. Will the water not spray in both the attachment hose as well as the floor part? Or does it spray in one or the other. You suspect that it may have a clogged line, is the machine doing anyt ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I bought the vac, used, but was told there was nothing wrong with it. I called the company, and was given the impression that it will be a huge headache to return it. Here's the best part: when I received it, I opened the box: it was broken. Clearly the highest internal piece of the vacume, whent he handle is removed, was cracked off, and in two pieces. The handle will not lock into place, so if I were to vacume forward, see ya, and the vac is back in pieces. Any idea how to rig this to get it t


... Dyson DC25 Vacuum

Electrolux Central Vac Hose Clogged


John,\015\012\015\012There are several handle types. The pump style has about 8 phillips screws that hold the handle together. Make sure it is not connected to the wall as some have 120V cords or direct connect pins to supply power to a m ... Electrolux Central Vacuum

Clogged hose I just accidently sucked up a sock and now I have no suction. I have no idea how to get the handle off and doubt this would help anyway. It is an Electrolux central vac. Help please!!!


If you have a drain auger then you can stick it in until it won' go any further then you have hit the sock.turn the cable and grab the sock and pull it to the surface.please leave feedback ... Electrolux Central Vacuum

We have a Beam1500 central vac. It sucks stuff off the floor, but then just clogs in the head of the unit.


The head itself is likely the power head..,which is sweeping but the neck is probably clogged. Detach your wand and look thru. Drop a coin thru your hose handle and shake thru the other end. If these are clear the issue is the head.Then check t ... Beam Industries 750 Classic Bagless Central System Cyclonic Vacuum

There's little or no suction on my central vac so I think maybe something is stuck in the piping. how can I troubleshoot and/or fix this?


First, check the hose, wands, and power nozzle. You can check the hose by dropping a coin in one end, then lifting the length of the hose until the coin drops at. If it doesn't, then there's an obstruction in the hose that needs cleared. Dependin ... Broan-NuTone CV450 Central Bagged Central System Vacuum

I have a eureka cv2301b central vac system that turns on and works when the system is plugged in but when operating the hose and head inside the house you cannot shut off the system even if you unplug the hose from the wall... Whats going on


... Eureka CV2301 Bagged Central System Vacuum

Rented triumph 430 and cant figure out how to work the accessories. I have the vac hose and a smaller hose attached ro dispense solution. There appears to be no way to plug in the smaller clear hose. Was I supposed to get another length of hose to connect from fitting on accessory to machine?


Yes don. call the store where u rented and tell them. ... Vacuums

Loud wailing noise . all clogs cleared . vac has full suction


... Vacuums

I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the


Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0571 seconds