Having problems with your Beam Industries Wet/Dry Auto Central System Vacuum ?
Beam Soft Touch handle electric harness replacement
\015 Bought replacement harness and can't figure out how to simply place harness back in with hose and get contact board to reseat and replace the hose set properly. Any diagrams for this? any tricks? Without saying, but I will, feel pretty stupid. Seemed easy enough when I unscrewed and opened up. The harness just a connector, switch and contact board for copper rings on hose that sits and attaches within the Beam Soft Touch grip housing. Any help would be appreciated.\015
Set the bottom part of the handle down(not the part that the screws go in)the contact board will fit into slots on the left side of thehandle half, the switch will go where the cutout is for it on the top, the plug is notched to fit at the lower front part of the handle. Then put the the tube into the hose and set it into the handle. There is a ribe near where the tube sticks out of the handle, it fits into a slot just before it sticks out. There also is a stop for the hose to up against so the contact rings can't slip off. Then put the other half on and screw it down.
Repair Help & Product Troubleshooting for Beam Industries Wet/Dry Auto Central System Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Beam Soft Touch handle electric harness replacement
Set the bottom part of the handle down(not the part that the screws go in)the contact board will fit into slots on the left side of thehandle half, the switch will go where the cutout is for it on the top, the plug is notched to fit at the lower fron ... Beam Industries Wet/Dry Auto Central System Vacuum
Replacing electric harness in Beach Soft Touch handle
... Beam Industries Wet/Dry Auto Central System Vacuum
DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each
Should be a pry off dot on the underside revealing a screw ... Vacuums
Mrs Cleaner flex has pulled out how do I replace Electric supply wire to switch on handle has broken at switch. How do you remove switch to repair? tonysimmons
Hi\015\012\015\012\015\012\015\012\015\012\015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum
The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu
This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums
Replacement motor I purchase a replacement motor for a F5897-900 Hoover SteamVa Motor part # 43576197 or 27242051. The replacement motor has three electrical connectors + ground were as the orginal has two electrical connectors + ground. Do I ingnore the the thrid connector and hook up the wires to the same connectors as the orginal or do I have to do some rewiring.
The manual only show one wire from the motor going to the switch, the other going to the cord, then the ground wire. I would wire it the way your old motor was, could be that some models maybe were 2 speed and the other wire would be used for that. ... Vacuums
Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless
Get over it and buy a new one!!! ... Vacuums
I had a house fire and lost most of my belongings. But I had just purchased a Shark Steam mop 3501. Loved it. Well it did not get destroyed in the fire but someone managed to break the handle off. Just the handle itself was broke off the rest of the handle rod is ok. I'm trying to see if I can replace the handle and not the whole shaft. Can you help me.
Yes you can replace jus the handle, the replacement part for the handle is available at the manufacturer's web site in the Parts and Accesories section. Enter M/N: S3501 to confirm it's the same as on your unit.\015\012\015\012 ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
The mechanical off/on in the handle is not working with the electrical on/off switch upon removal of the handle you can cut the machine off by hand but after ensuring the the handle is re-placed in the proper position the machine will not turn off so what new handle or is the rocker switch has worn is now to hard for the mechanical switch to operated
Hi there it's SmartAlec from NelsonVacuums.com.au here. You are spot on in your diagnosis however i have fixed heaps of these and i have found no way to tell wether its the ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
I am replacing the hose on my kenmore canister 11622612200. i easily replaced the handle end of the hose, but cannot see how to replace the end that goes into the canister. can you tell me how to disassemble the canister end for the new hose? many thanks!
Open the canister and locate the hose intack. There is a plastic retainer which slides over the end of hose and is secured to the body of the canister with a few screws. Remove the screws and pull the retaining ring up to release the hos ... Vacuums
I have a Kirby Heritage Vacuum Cleaner. Recently the handle fell backwords. I took the pin to the handle out and replaced it. It helped some, but the handle does not stay upright.
... Kirby Ultimate G Bagged Upright Vacuum
Bisell Healthy home vacuum stopped working. The troubleshooting guide said there could be a problem in the connection at the handle. None of the phillips screwdrivers we have seem to work in removing the screw that holds the handle to the vacuum. What size phillips screw driver should we be using? If the screw is stripped, how can we get it out to replace it since it is not easily accessible in the handle?
You should use a p2 size phillips. there is only one screw right in the center that holds the handle assy on. frequently that screw backs out and allows the handle to slide back and loose connection. make sure the handle is tightly pressed in and the ... Vacuums
The extension has lost suction. If I remove the handle tube part, the suction is great to the bendy part, but as soon as I replace the handle part there is none at all and there is no blockage in the handle tube part.
... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum
The handle release pedal wasn't allowing the handle to lower. I took off the pedal and saw the spring load part was broken. What is this part and how to replace it? Bissell 3760-3 handle release
Our vacuum recently had an issue with it's motor, we had to borrow a neighbors a couple times while we were trying to figure out what to do. We decided to take it to a place that specializes in cleaning supplies and cleaning tools to see if they had ... Vacuums
Need to replace lower handle and pivot as it broke off. I got replacement but no instructions how to replace.
Our dustbuster (dont' have model number with me-sorry) won't turn off when I pull back on the switch handle. I disassembled the unit and realize that the tab on the switch handle that pulls back on the internal switch handle to turn it off is not strong enough for its simple task. Does B&D have a proper replacement part?
If you can provide a model number, I can check availability of the switch and can either order it for you, or supply the B&D part number and you can order it from most local vacuum shops in your area or from Black & Decker direct online: ... Black & Decker 15.6 Volt DustBuster Vacuum
I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the
Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums
Handle broke handle of 2961avz somehow snapped in half. any ideas how to find a replacement handle?
Part # for the handle is 75765-3. You should be able to order thru a local service repair shop. ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum
My 8 yr old kenmore vacuum works well - however the hose has worn under the handle where there is a hole (resulting in decreased suction power). I'd like instructions on opening the handle and bypassing the worn piece of tubing rather than replacing it for $129. Some of the handle screws remove easily but the last one doesn't loosen easily.
Hi,Have you tried spraying the stubborn screw with WD40 and let it soaked for a while? Other than these screws holding the handle together, there would no other way of opening it up. Hope this be of initial help/idea. ... Kenmore Vacuums
How to remove the bag housing from the handle in order to replace the power cord on a Hoover vacuum U5209-930
... Hoover Vacuums
How do you remove the Handle from the Hoover Windtunnel Deluxe to replace the switch?
Removing the handle assembly should be easy after removal of the two screws. It may be binding or hanging up on the self-propel cable...or the plastic may just be stuck/binding. Note that the handle slides in and out of the vacuum unit along the sa ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum
Hoover Handle Release Pedal Replacement--How is it possible?
If you look at the picture, the slots are right across from the drive wheels, you can see the slots in the picture. Use a flat blade screwdriver. ... Vacuums
Bissell 6590 the part I am trying to replace allows you to lower the handle to lay flat to get under furniture and it also allows the handle to stay in the upright postion. i have looked on bissell.com and did not find it-but I will try again. you are super and Thanks allot . Have a super easy day! Michele
It is called the detent lever part # 2030052. If you can't order it from bissell.com or over the phone, most repair shops should be able to order it for you. ... Bissell 6590 CleanView Bagless Upright Vacuum
Brush roller spins until it touches the carpet, then stops. I have already replaced the belt and it continues to stop when it touches the carpet
Saw another answer saying to put electrical tape on the brush roller where the belt contacts it. I was thinking that the brush roller bearings have probably worn out, and the roller needs to be replaced. But electrical tape is a lot cheaper. ... Eureka Smartvac 4870 Bagged Upright Vacuum
I had to replace the handle. The wiring is inside the handle. I would like to verify the position of all the switches and the location of a spring that fell out.
Dear Heidimtaylor,\015\012\015\012For this first we will required your model no. I will advised you too visit the following site and search for your model's service manual. It contains details which you required. Following link will help you... ... Vacuums