Having problems with your Beam Rugmaster Plus Belt ?
Change belt How do I open the power head to get to the belt to change it?
Repair Help & Product Troubleshooting for Beam Rugmaster Plus Belt
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Change belt How do I open the power head to get to the belt to change it?
... Beam Rugmaster Plus Belt
Change the belt in my kenmore power-mate 120 amps...how to open it to get to where the belt is???
HELLO, JUST REPLACED THE BELT ON OUR'S. FIRST TAKE LITE LENSE OFF THERE WILL BE 2 SCREWS, REMOVE. THEN FLIP OVER POWER MITEON EACH SIDE PRY WITH 2 SCREW DRIVERS WHERE THE ARROWS ARE TO SEPERATE & THERE IT IS THE BELT. MIKE ... Kenmore 23313 Whispertone Bagged Canister Vacuum
The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?
Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
I cannot get the Kenmore power-mate open to change the belt? How does it come apart?
... Kenmore Vacuums
How do I change the belt on the Miele vacum SEB234/236 Power Plus (power head)
... Miele Vacuums
The motor on my Epic 6500 works, the hose is sucking, but the power head isn;t working... I tried the sidestep power head and that one works. Ive opened and replaced the belt and that is fine. The bulb was already burned out and wasn't replaced so I cant tell if theres power to the head. What else could it be?
Connect the power nozzle directly to the hose and try.\015\012Check the terminals where the wand connects to the PN. If any are discolored or cracked, that may be the problem.\015\012Open the PN and check for loose or broken wires and co ... Electrolux Epic 6500 Vacuum
Chang the belt in my kenmore power mate power head
... Kenmore 25512/ 25513 Progressive Canister Vacuum
How do I change the belt on the side. Have a Bissell Power Lifter. The belt broke and i cannot get it changed. HOW do I change it?
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
Broken belt I have a royal canister model 4750 with a broken belt on the power head. I don't know how to disassemble the head to get at the belt.
If you have the power head with the headlight, squeeze the sides of the upper part (almost like a superstructure,) where the headlight is located. It should lift off, allowing access to the screws to get the powerhead apart the rest of the way, and o ... Vacuums
How do you change a belt for the belt on the Royal Part #2-470010-801, Power carpet head attachment for the Royal Classic Power Team canister model #4750?
... Royal Vacuums
I've got a Kenmore canister vacuum, Progressive 236123, and there's a burning smell from the belt side of the head--smells a lot like hot rubber. I've cleaned the agitator and changed the belt, but I still get the smell. It's stronger when I'm using "carpet" mode than when I'm using "bare floor" mode. Any ideas what the problem is?
... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum
Need to change belt on hoover upright model u5093-900, but can't figure out how to open it up to get at the belt.
... Hoover Vacuums
HAVE A RC1400 THAT WON'T RUN. BELIEVE ITS THE POWER CORD BUT CAN'T GET THE VACUUM OPEN . THERE ARE FOUR DEEP HOLES IN THE CASE BOTTOM BUT WHATEVER IS IN THEM , JUST HAS A FLAT ROUND HEAD, NOT PHILLIP'S HEAD OF SLOT. J F
Should be size 15 or 20 torx bit screwdriver required ... Riccar Vacuums
Change belt on Hayden power head
... Hayden Industries Vacuums
How to open power head of Nutone CT600
I have an eureka power plus vacuum floor cleaner and i have no way of opening the botton to the brush to change my belt for the brush since the brush will not turn.
Look for two screws at the edge of the brush housing. You may see these ones on top. They will be black and recessed ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
How do i open my vax power 5 to change the belt for rotateing brushes
... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum
I have a Broan Nutone central vacuum. The power head seems to stall unless you lift up on the handle. I think I may need to change the belt but cannot find a place to purchase one to see if this is the problem Model number BN180 type 1
You are correct, you need a new belt. You can find belts for the Broan BN180 at www.vacbelts.com. ... Vacuums
I have a fantom power pet model #fm722c how do i get inside to change the belt or remove the dirt from inside as well as the vacuum is not sucking the air thank you gail glandon
I have just cleaned out my filter and now it does'nt go back together?????Please help asap. It is a power/pet model ... Vacuums
The brush on my hayden 6000 supervac is not rotating when power is on and i can't figure out how to open the vac to get to the belt. help please
First you will want to remove the light cover. this can be done by pusing as you look at the front of the powerbrush on both the left and right side of the head. There you will find the lightbulb and 2 screws to remove. Remove both of the screw ... Hayden Industries SuperVac 6000 Central System Vacuum
I have a Bissell Turbo - Powerforce Model #6585C - I want to know how to change the belt in the power head?
First go to this website and click to download the PDF of the manual for this unit:\015\012\015\012http://www.bissell. ... Bissell 9200 Upright Vacuum
MY hooverselfproweled windtonel sound like an air craft getting ready to take off and lost alot of sucking powers. I had it serviced at a local store. It wasn't right when go it back. All belts and filters where changed.
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=761558\015\012Generic problem for all Vacuums\015\012MY Hoover self propelled WindTunnel sound like\015\012 ... Vacuums
How do you change the belt in a ct18dx powered brush head?
... ASUS Vacuums
Hi -- I have a Kirby Sentria and it is great except that I am getting no suction at all through the big silver power head. Suction through all the other attachments works well. I haev tried it with the roller belt on and off, and that doesn't seem to make a difference. Am I missing something?? Thanks!
You can take off the power head and look in that whole where the belt is and see if there is a paper towel or something in there clogging it up. Also tug on the belt and make sure it is tight - because if it is loose it is broken and you ... Kirby Vacuums
How do you open up the power head to check the belt?
Turn the power head over so the bottom is facing up. On the bottom towards the back there are two holes (one on each side) where you can get to the access screws. Remove the two screws (you'll need a phillips screwdriver). With the screws removed you ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum