Having problems with your Bissell 1400 Little Green Pro Canister Steam Vacuum ?

I think the pump needs to be replaced in my Bissell little green machine. Some water/solution is being pushed through but not enough to spray only drip, if I hold the machine up high while using it (ie on a table) it will spray a little. Is the pump easy to replace? is there anywhere to get a parts diagram?


Answers :

I got my Little Green ProHeat when the product was first unveiled\015\012several years ago. Shortly thereafter, the nozzle itself developed a\015\012clog in the spray jet. Remove the nozzle from the end of the hose, and\015\012with the machine running pull the trigger. If a great amount of\015\012solution comes out of the supply hole, then your nozzle is clogged. \015\012You can try clearing it with a very thin pin and then rinsing it out.
\015\012
\015\012In about 6 months, my pump would no longer spray solution at all but I\015\012could hear the tiny pump still running inside the machine when I would\015\012pull the trigger. Remove the tanks, unplug the unit, and look\015\012carefully and you will see the few screws holding the unit together. \015\012Pull it apart carefully and don't use much force as some of it snaps\015\012together and you don't want to break those tabs. Once open, you can\015\012find the solution pump, a little fella. The drive shaft on the motor\015\012that spins the pump had rusted away completely! Design flaw. In lieu\015\012of getting it repaired, I simply started using a spray bottle for my\015\012solution application. Several years later and I'm ready to take the\015\012time to replace the pump - a very simple process. From the research\015\012I've done, the part number for the solution pump is:
\015\012Manufacturer's Part Number: 6035029
\015\012If you google search "Bissell 6035029 VacPartsWarehouse" without the quotes, you should find your part there for around $9.
\015\012
\015\012Try this direct link to VacPartsWarehouse's website:
\015\012VacPartsWarehouse Bissell 1425-2 Little Green ProHeat
\015\012Click item #9. It's very simple to install. If you can wield a\015\012philips screwdriver, and pay attention to how you've disassembled the\015\012unit and then just reverse the steps, you can fix this yourself on the\015\012cheap.
\015\012
\015\012Good luck! :)
\015\012Dan
The motor for the pump rusts because the design of the pump does not seal well against water leakage. Water gets out (the only thing that seals it is silicone grease) and rusts the motor. It can get so that the front of the motor shaft wobbles and that makes the leak worse.

As noted, a new pump/motor assembly is cheap. If you get one and replace it, don't forget to tie-wrap the hoses, as the factory does, or you will get leakage at the hoses.
Repair Help & Product Troubleshooting for Bissell 1400 Little Green Pro Canister Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I think the pump needs to be replaced in my Bissell little green machine. Some water/solution is being pushed through but not enough to spray only drip, if I hold the machine up high while using it (ie on a table) it will spray a little. Is the pump easy to replace? is there anywhere to get a parts diagram?


I got my Little Green ProHeat when the product was first unveiled\015\012several years ago. Shortly thereafter, the nozzle itself developed a\015\012clog in the spray jet. Remove the nozzle from the end of the hose, and\015\012with the machine runn ... Bissell 1400 Little Green Pro Canister Steam Vacuum

I brought an eureka model 2591av shapoo machine in 2004 I've only used the machine 4 times. now the it does not spray out the solution on the floor but it will **** up water, the vacuum part works. I took it to a repair shop, they said it was the pump that was broke and will cost $95.00 to fix. The purchase price of unit was only $129.00 My question to you is does that sounds like an honest or comparible diagnosis.please respond at ([email protected])


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=559297\015\012Generic problem for all Vacuums\015\012I brought an eureka model\015\012Posted by wadda08 on Apr 3 ... Vacuums

I need the spray pump motor hold down. accidently put it down the toilet with the dirty bucket of water while cleaning the machine out.


... Bissell 1720-5 Little Green Turbobrush Canister Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I have a bissell proheat carpet cleaner purchased in 4-18-2005 for $169.99 from kohls I have used it 6 times and the last time the brushes would not move cause the belt was broken and the end of the pump pulley which is plastic broke off so I reorder the pump unit and 2 new belts and now I see you have sent me a exact pump but the end that broke off that the belt rides on is made of steel or aluminum much strong piece of equipment I want to know if there was a recall for the machine due to mecha


I've owned my Bissell for over 5 years now & LOVE it! Even after vacuuming It pulls up tons of dog hair I never realized was there! I am having a similar problem, but I caused it myself & think maybe you may have the same problem, cross you ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My Bissell powersteamer has no spray releasing for floor cleaning. The spray attachment for upholstery is working. The tank is seated properly: The belt is attached properly. I bought this machine in Sept. 2009 and used it only 2x with no problems. It did a fantastic job. Can you help with this dilemma? Mark


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

No spray I have a proheat cleaner. The problem is there isn't any solution when I press the trigger on the handle to use the machine to clean a whole carpet yet if I use the handheld unit it works a treat. I have tried all the remedies in the manual.


\015\012Here are 3 common things that causes this problem:\015\012\015\012• clogged spray tips \015\012• defective solenoid valve in the base \015\012• defective trigger microswitch in upper handle ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Not spraying The machin e is new and i use it a few days ago, we cleaned it inside and out, it is not spraying any cleaner or water. Can you help me?


• tanks are not sealed into receivers• faulty auto load receiver• pinched/clogged line• defective component allowing air into system• pump not mounted so it can move freely• defective bridge ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have Bex Bissell Proheat. It is one problem requiring fixing each time I use it. Just had a new pump fitted as water not spraying out. Now the water is not being sucked up. For the money this has not been a good product. When it works it is good. But the constant issues each time it is used is frustrating.


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

The needle is to the left and back of center, frequently hitting the plate and breaking. The hoop came unsnapped while embroidering, and caused needle to bend, stopping the machine. That was no doubt when the shaft that holds the needle became askew. How do I reposition it? I don't see an appropriate category listed below. Small appliances is as close as it gets, which does not give me a high level of confidence of having an expert for my Babylock Espree EM2 embroidery machine on your staff


I work on my wife's sewing machine all the time and saw your post when I was about to leave but I have a couple of appointments to go to.Although you say yours is for embroidering,it should not matter.When I get back I will take a look around and see ... Vacuums

My machine makes a terrible(bearing type ) noise when I push the pump button, and it will not spray out solution


... Rug Doctor 95341 Wide Track Professional Carpet Deep Cleaner

George wet & dry machine spray pump stopped working & makeing buzzing noise


... Numatics Numatic George GVE370 -2 George Wet-Dry-Scrub Green Vacuum Cleaner

ShopVac pump The waterhose connection is up high. The only way to get the water up to the level of the hose is to continually hold down the on button due to the automatic shut off after it fills to a certain level. On the bottom of the filter there is a hole. I am thinking there should be a small hose of some sort to put into that hole that would then lead up to the level of the water hose. Concept makes sense to me. But in the meantime, good old duct tape seems to have done the trick. Not exact


Hey thats great whatever works its what makes america great ... Shop Vac 584-06-00 Canister Wet/Dry Vacuum

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet


Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums

I have the bissell proheat 2x used it twice and it no longer sprays out water from the machine or the tools


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would


... Hoover L2310 GUV Central System Vacuum

Replaced the pump for a 9300 M Bissell Proheat 2x as the water solution was not releasing to the carpet. Once rehooked the lines the solution appears to be coming from the water tank and returning to the used tank and bypassing spraying on the carpet. How can I be sure the hoses are hooked up correctly?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Nothing spraying out of Bissell Powersteamer Proheat. I've check filter under flow indicator, pump belt is fine, cleaner in proper tank, bladder of water tank is full. We've had it for a very long time but it's barely been used. Can anyone help?


... Bissell 1698-1 PowerSteamer ProHeat Plus Upright Vacuum

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?


Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

There is no spray coming out of the machine when I pres trigger.Tried all bissell tips,is there any place to get a prodecure for getting to the pump? Thanks-Andy


... Bissell 1400 Little Green Pro Canister Steam Vacuum

Bissell 1770 No instructions came with my new 1770. There are three long screws only one of which has a place to screw in---to hold the handle. No instructions on how to use the machine, Help!!


Go to Sears with the model # and they can order a manual and ship it to your home. ... Bissell 1770 Quicksteamer II Upright Vacuum

Hoover Steam Vac ; The vac is not dispensing cleaner/water. I suspect the tubing/path from tank holding the cleaner/water mixture is clogged. Is there an easy way to unclogg it. Are there are sketches/drawings showing the path and where it is is the machine.


Hi there,Just a quick clarification please. Will the water not spray in both the attachment hose as well as the floor part? Or does it spray in one or the other. You suspect that it may have a clogged line, is the machine doing anyt ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Smartmix bottle When I put a full smartmix bottle in the machine, the fluid sprays out even with setting at water only and not holding trigger. Then it stops regardless of smartmix seting. Thanks, Terry


The cap and insert at the bottom of the bottle may need to be replaced, or you could have a problem with the smart mix asm. You would have to remove the top cover to get to it. Does the smart mix knob stop where it is supposed to or does it go all ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1291 seconds