Having problems with your Bissell 1425 Little Green ProHeat Handheld Steam Vacuum ?

The sprayer seems to have stopped spraying water, and it was working fine yesterday. Any thoughtson how to fix this?


Answers :

I have had the same problem. Usually it's the soap, which has gummed up. I have soaked the head in hop water and this has taken care of the problem. I make sure to do this after I use it, and at times, filling the tank with clean water and run this through to clean out any residual detergent.. Hope this helps.
Repair Help & Product Troubleshooting for Bissell 1425 Little Green ProHeat Handheld Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The sprayer seems to have stopped spraying water, and it was working fine yesterday. Any thoughtson how to fix this?


I have had the same problem. Usually it's the soap, which has gummed up. I have soaked the head in hop water and this has taken care of the problem. I make sure to do this after I use it, and at times, filling the tank with clean water and run thi ... Bissell 1425 Little Green ProHeat Handheld Steam Vacuum

I cleaned my carpet cleaner and everything seems to be working fine besides the fact that it will not **** the water up from the floor. What can I do? Is there anyway to fix this problem/


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!


Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum

The KP1010 was at rest all winter long. It has worked beautifully before this. It is now working but we can't stop it from brewing. It works but it delivers the water at the rapid cycle. We have water all over the place. Is there a way to fix this?


Sounds like the flow meter is stuck open, letting water keep running. Go to www.krupsusa.com. Then to parts, then pick your model number, this will give you all parts for you machine. Also click on schematics and it will give you a breakdown for your ... Vacuums

I have the Bissell Proheat (7901) It will pick up water and the hand tool works fine. I noticed that the red indicator stopped spinning. Then I noticed no water was coming out. If I put down water using the hand tool, the vacunme will pick it up. When I called Bissell they had me do something with the indicator. When it didn't work they said take it in for repair.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

No water I have had a bissell proheat for 3 months. Now, the water won't come out in either the floor cleaner, or the tools. I have checked all the stoppers, they all seem to be in working order. It started to work for about 5 min, then stopped again. Is this a fixable, quick problem, or should I return it as being defective?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My bissell pro heat 2X has stopped dispensing water from the tank, the suction is working and it seems to be dispensing the detergent, so it is not rinsing or washing with water. I have cheaked to see if there is a blockage but that doesn't seem to be the problem...please help


I have a Proheat 2X and had the same problem. I tried the Water Rinse setting and found water came out and was suctioned properly, but on the Light Clean, Normal Clean, and Heavy Traffic settings, the unit failed to do anything. Problem may be with l ... Vacuums

Stopped working Was working fine then it smelled like burning rubber, not the belt I checked. It sounds like the motor wants to run then it just stopped but the light is on. What do you think, go by a new one?? This has been a great vacuum cleaner and I can not seem to find a Sharp anywere. Thanks for your time.


Well it could be the motor, if it is it would cost around $80 or so for a motor. May be better to buy new, thre are a number of good brands out there. ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

My Bissell Pro Heat Pet will spray water but not pick it up when cleaning the carpet. Is there anything I can do to fix it? The furniture attachment hose picks up water well. It seems like it could be a bit more powerful of a draw on water. I don't know it that has something to do with why the floor cleaning sucktion doesn't work. Thank you for your time. Jenn


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Bissell Vacuums

My Bissell ProHeat 2x is pouring water out of the bottom anytime it's turned on. I had it in the shop for no water, took it back again for the same problem, took it back again because it had no suction, finally took it apart and found the problem with the suction and fixed it myself. Worked fine for a day and now it is constantly leaking water, if it's turned on, and is useless for anything except for making a mess.


Took the unit apart and discovered my heater had small pinholes in the metal and they had put in silicone, instead of a gasket, which didn't seal. So much for the place I took it to "saving" my heater for me. I repaired it myself by getting a few o ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current


I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum

The unit (9400-3) is not spraying water from the lower deck but will spray from the hand held wand. Checked water levels and water/soap dispenser valves which seem to be working fine. Spray nozzles are not blocked. Where do you look now.


Same problem i have got, spent one day on the bloody thing but of no use, the only solution is to spray water from bucket and use the cleaner to **** it up. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Dewalt dc500 wet/dry vac won't **** anything up, I’ve put a piece of wire to not the float ball from moving them it work fine but if I remove the wire I stop working the float ball moves to the top like it is full of water? Can you please help?


... Dewalt DC500 Canister Wet/Dry Vacuum

Our DWC-41CR water dispenser is not working, the hot water is fine but it is not making the chiller side cold. Can it be fixed? It is only 2 months old.


... Daewoo Vacuums

Bissell Powersteamer 1694W won't extract water from carpet. Was extracting fine until the pump/brush belt gear broke off off the pump. I repaired the gear with super glue and the brush is once again working fine. I now have an extraction problem. What did I do wrong? I took it apart and was so proud of myself when I fixed the original problem. Now I'm lost.


Check your re-assembly.\015\012\015\012Have you missed a pipe connection somewhere? ... Bissell Powersteamer 1694 Upright Vacuum

I have Bissell ProHeat 2X 9300-M that I tried to use again today. Is does not dispense solution when turned to Floor Cleaning, when switched to Hose it seems to be working fine. Brushes and suction are working as well. Soap and water containers are full. I took off and replaced tanks, waited to prime the pump multiple times without success. Not sure what is going on.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My steam pocket mop seems clogged. Steam does not come out of the mop head. The clog appears to be in the rectangular mop head. The triangular head still works fine. I've tried soaking it in hot water and soaking it with cleaning solutions. They have not worked. If I blow into the connection piece, no air goes through. That's what leads me to believe there is a clog. If you can help, please do. I like the product and haven't been able to use it for awhile because of this. Thanks.


I had the same issue with the rectangular mop and corrected it by disassembling the tube from the rectangular piece. There are two screws that will need to be removed in order to get access to the connector. Once the connector is removed from the rec ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?


The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

My scooba seems to work fine but no longer makes the beeping noise. Several weeks ago the beep was sounding very strange almost like a battery was dying. Now it's not making any noise at all. Is this the beginning of more problems or can the machine function just fine without the beeps? If not then how can I fix it?


Your speaker went out. It could be totally isolated. You're not going to be able to determine what's wrong with your Scooba if something does happen, though, because without those beep codes, there's no way for the robot to communicate with you. ... iRobot 5900 Scooba Robotic Wet/Dry Vacuum

1. Bissell Model #7350-C 08249C Carpet Cleaner 2. No soap & water is coming out of machine 3. Worked fine yesterday but isn't working today, we have disconnected it and cleaned all visable places.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.


Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

No Suction My two year old Kenmore Progressive stopped working in January. The guy at the Sears service center convinced me that buying a new one would be cheaper than getting it fixed. So I bought the exact same model and now this one has given out in the exact same way! I'm so confused. When I press on, it lights up and makes the whirring noise. Everything seems to be working but there is no suction anywhere. Not in the main part or the hose and there's no "cyclone effect" in the chamber. All


Try looking within the vacuum to see where the suction is getting stuck at. You may have to do some disasselbmeing but this is a manufacturers problem. You should also try to speak to the manager at the support and make a big dispute until you get yo ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks


If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0935 seconds