Having problems with your Bissell 1425 Little Green ProHeat Handheld Steam Vacuum ?

When the machine is turned on there isn't any

\015 No suction from the hose when the machine has been turned on. I have confirmed that the hose doesn't have any clog issue so I can't figure out why when the machine has power it doesn't extend to the hose.\015

Answers :

DID YOU CHECK THE FILTER?
Repair Help & Product Troubleshooting for Bissell 1425 Little Green ProHeat Handheld Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Restrictive valve moments after starting the vac the red ball rises to the top and the machine quits sucking. I turn the machine off, the ball drops, I turn the machine on, the ball rises the machine quits sucking, I turn the machine off the ball falls, I turn the machine on........etc. What am I doing wrong? It works fine and then all of the sudden it starts the same stuff again. I thought it was because the retrieving container was getting too full or the cleaning soln container was not full e


The foam filter on the bottom of the tank lid is too far up. Pull it down so you have at least a 1/4 inch gap from the top. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Brushes won't turn on the bissell proheat 2X steam cleaner-I don't have the manual to see if there is a button I am not pushing to turn on the brushes. Also, do you put the clean water in the "bladder" in the tank? Sorry I am so dumb-this cleaner was given to me with no manual and I can't figure it out. There is a small tank on the bottom at the back of the machine, that says "formula here" and I don't know if that is where the cleaner goes or what that is for. The machine turns on just fine


... Bissell 8910 ProHeat Clear View Upright Vacuum

Hi i bought a fog machine from target and it told me to let the machine heat up and once the light turns red to turn it on so it can produce fog but its not producing anything. do you know what could be wrong?


Wish I could help, I bought two of them from Target and they both worked for about 15 minutes then stopped producing 'fog'. ... Vacuums

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?


Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

The machine backs out of the dock, then proceeds to turn in circles, stop and then start turning in circles again. I have cleaned all of the sensor areas and made sure the bumpers were not stuck against the machine. Any ideas


... iRobot Roomba 560 Robotic Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

The brushes on the Hoover All Terrain Steamvac won't turn. However, when I try to turn them manually they will turn. So, why won't they turn when the machine is turned on?


Some vaccums have a belt on the brushes. might need a new one if it does have the belt ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th


... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

My Janome Harmony 8100 will occasionally stop and give me a System Error #1 - I cannot find anything about this error. It is a computerized machine with 70 stiches and attachable embroidery hoop. I first started getting this error with the hoop and now get it when I am just sewing. As soon as the needle goes down to the bobbin, I get the error. The machine freezes and the only way to get rid of the error is to turn the machine off. Sometimes I can get the machine going again, but now it wil


... Vacuums

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?


Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My electrolux2100 every time i turn it on it stays on for about 1 min then the proctection button come on then the machine turns off i wait a second and then it turns back on and does it again what can i do


First, turn dial on top of vacuum counter-clockwise so the smallest dot lines up with the arrow. See if it stays on. If not, detach hose and turn vacuum on. Place palm of hand over intake. If it turns off, it's possible that the tubes connecting to t ... Vacuums

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Brother computerized sewing machine BC-2500: While I'm sewing the machine stops and comes up with error "F4". Now every time I turn on my machine this is all it does.


... Vacuums

Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance


Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?


As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My brushes do not turn on my power glide pet vacuum cleaner after I accidentally sucked up the hem of a curtain. I switched off the machine then removed the hem. Now when the vaccuum cleaner is turned


... Electrolux Vacuums

Red Ball I have a Hoover SteamVac Delux. The red ball pops up as soon as I turn the machine on, even though the tank is empty, so the machine will not **** any dirty water out of the carpet. Any suggestions?? ZThanks.


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Motor problem machine is smoking/burning smell coming from the bottom of the machine. Motor still turns but doesn't make much sound; and soulution won't squirt. The model # is 1970


I had to throw the machine away before it burned my house down. There is no way to fix it; had to replace it. ... Bissell 1770 Quicksteamer II Upright Vacuum

We have the bissell quicksteamer and as I was shampooing I began to notice something burning so I unplugged our machine immediately; then my mom and I started cleaning all the filters assuming that could be the source of our problem and yes it was a little dirty but I suspected that it would take more thant that to cause our machine to somke soI turned it upside down and noticed there is a cable of copper threads that appear to have some type of rubber or plastic insulation tubing around it but


Was the exposed copper wiring on the electrical cord? If is then replace the cord. The main problem with this model is that Bissell obsoleted it as well as parts for it. But if all you need is a cord, you should be able to get one from a repair shop. ... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

Hi guys, I have a bissell 9400 2x proheat with a fault. When you turn on the machine it trips the RCD in my house and makes a poping noise, i am a little technical so i had a look inside. The pcb under the handle was damaged with burn marks i unpluged this and tried again and the machine powered up, don't think the rollers moved though. What do i need to change roller motor,pcb?? Help please!! Regards Russ


I've seen the same problem in one of these we had in for repair. The pcb in the handle is involved with controlling the roller motor. The problem is with the motor. In my view, this machine is a triumph of design over practicality... The motor is loc ... Vacuums

My Pasquini Livia 90 S/E will not stop heating water. This builds up too much pressure. I have unplugged the machine and let it cool off and turned it back on and got the same result. I can relieve the pressure by opening the steam valve, but since the heating element does not turn off it builds up too much pressure very quickly


Your thermostat is failing. Given the initial price tag, look at your warranty options first. If you are out of warranty, then lets proceed.Since there is not a parts / assembly diagram to be found, you will need to disassemble your esp ... Vacuums

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

The Shark steam cleaner wont turn on when plugged in. Is there somewhere on the machine where maybe a fuse was blown or shorted out and needs to have a switch turned back on?


... Euro-Pro Ultra Steam SharkTM II Hard Surface Steam Cleaner Vacuum

The mechanical off/on in the handle is not working with the electrical on/off switch upon removal of the handle you can cut the machine off by hand but after ensuring the the handle is re-placed in the proper position the machine will not turn off so what new handle or is the rocker switch has worn is now to hard for the mechanical switch to operated


Hi there it's SmartAlec from NelsonVacuums.com.au here. You are spot on in your diagnosis however i have fixed heaps of these and i have found no way to tell wether its the ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have checked the machine for blockages, none found.However, the machines turns off after running for about one minute. Any ideas?


The electric motor inside your Dyson has a built in over-current trip to protect itself (and you if it seriously overheated and caught fire). This normally automatically resets itself, however if the motor has just about had it, next time it is switc ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0482 seconds