Having problems with your Bissell 1425 Little Green ProHeat Handheld Steam Vacuum ?

We need a replacement hose because the puppy chewed ours up.... I haven't been able to locate one. Any suggestions?


Answers :

Get your phone book out and call your local Vacume cleaner repair shop -- they will be able to order it for you if they do not have it in stock.
\015\012or you can order them online and have them shipped right to your door:
\015\012www.bissellreplacementparts.org
\015\012or :
\015\012www.bissell.com
\015\012
\015\012c...
Repair Help & Product Troubleshooting for Bissell 1425 Little Green ProHeat Handheld Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We need a replacement hose because the puppy chewed ours up.... I haven't been able to locate one. Any suggestions?


Get your phone book out and call your local Vacume cleaner repair shop -- they will be able to order it for you if they do not have it in stock.\015\012or you can order them online and have them shipped right to your door:\015\012 ... Bissell 1425 Little Green ProHeat Handheld Steam Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Looking to replace the hose swivel on a Sears vacuum model 116-23612. We have the new part but can't seem to get the old one off. Suggestions?


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

I need to change out the short hose on the underside of my older Dyson DC 07 Animal (Light Purple). It is the one less than a foot long on the underside which is attached on one end to the main body of the vacuum(I was able to remove this one) and the top of the upper soleplate. The latter one seems to be glued or otherwise permanently attached.Any assistance you could give me on this would be greatly appreciated....Thanks


Hello Cynthia,\015\012\015\012It's not glued, but it can be a little difficult to remove. You need to twist and pull at the same time and it should pull off. If it's being stubborn, squirt a little bit of WD40 / penetrating fluid where th ... Vacuums

I own a old Bissell Big Green Cleaning Machine and am looking to replace the inline fluid/vaccum pump. The pump has an Eaton logo and is model CP7. I have not been able to find a replacement at your site. Could you tell me if one is still available or where I might find a replacement?


I just saw one on USAVacuum.com It's about $29 ... Vacuums

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each


Should be a pry off dot on the underside revealing a screw ... Vacuums

Where can I get a replacement glass lid for Rival crock pot model #3100/2? The one listed below is out of stock, but, even if it were, it will not fit my model. Any suggestions? "Buy-it-now-store.com" lists: CURRENTLY OUT OF STOCK, NO ETA. # Rival Crock Pot Lid Replacement Glass for 3.5 Quart Rival Slow Cookers - $5.99 Rival Crock Pot Slow Cooker Replacement Round Glass Lid Cover # Works with Rival Crock Pot Models: 3100, 3101, 3102, 3103, 3130, 3133, 3120, 3250 # Approximate total


... Vacuums

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

Pls Help! My Dyson DC05 (Yellow) needs a new wand. Am unsure whether it is the assembly wand or hand one found in spare parts. The wand I need to replace connects the two long hoses together, and NOT the wand which fits onto pickup head. M.thks if you can advise which one I need. Getty rather dusty in my pad!!


... Dyson DC05 Bagless Canister Cyclonic Vacuum

A 'burn' hole has appeared in the Microwave Outlet Cover causing arcing (or similar sparking and blue flashing!). Would replacing this cover with a new one solve the problem or does it suggest something that would quickly reoccur? Would it be an economical repair or should we ditch the machine for a replacement? Thanks in advance etc it is appreciated.


... Vacuums

The motor on my Epic 6500 works, the hose is sucking, but the power head isn;t working... I tried the sidestep power head and that one works. Ive opened and replaced the belt and that is fine. The bulb was already burned out and wasn't replaced so I cant tell if theres power to the head. What else could it be?


Connect the power nozzle directly to the hose and try.\015\012Check the terminals where the wand connects to the PN. If any are discolored or cracked, that may be the problem.\015\012Open the PN and check for loose or broken wires and co ... Electrolux Epic 6500 Vacuum

I have a 144w305 long arm industrial sewing machine i am looking for a bobbin case to replace old one. i am getting alot of skips and was told i need to replace this. any suggestions. thank you


... Singer Vacuums

HI, I replaced the old hose a while ago the new hose is now shutting off constantly. Any suggestions?


I would check for blockages. Test the suction at the end of the hose and then remove the hose and test the suction at the machine. If there is a significant difference you will need to remove the blockage or get a new ... Miele s558 Silver Moon Vacuum

The hose split. I ordered a replacement but can't figure out how to remove or loosen the back panel to get the old hose out and the new one in.


Hello,\015\012\015\012I'm sorry, I thought I had one of these models in stock here so I could take it out of the box and photograph this repair for you. Unfortunately I didn't have the exact same model, however I do have a similar model ... Eureka Smartvac 4870 Bagged Upright Vacuum

Dyson DC07 I actually need to locate and replace the brush as it split on one end. Looks like I need to pull the belt off to do that. Might as well replace the belt while I'm at it.


Hi.\015\012\015\012Depending on wether your machine has A clutch fitted will decide how easy this job will be.\015\012\015\012The non clutched model is very simple turn the 3 plastic screws on sole plate to unlock position lif ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The vaccum has been cleaned and checked but the brush is not rotating and no suction at the bottom, but through the hose. In reading the instructions to remove the brush cover it says to lift tab one and release 2-4. Where is the tab for tab 1 can not find anything for tab one to be able to lift, nothing there any ideas for help would be greatlly appreciated/


3 on the front and one on the back. where the belt runs ... Bissell 6594 PowerForce Bagless Upright Vacuum

Hello, I have a Kenmore Progressive Canister Vacuum 116.20912006. It won't turn on. On the hose assembly, the end where the hose swivel is, there are 4 metal pins that plug into the canister. One of the pins looks like it broke off. There are only three pins remaining. I assume there should be four pins as there are four holes. Is this the problem and is it fixable? The vacuum is from 2002 so I am not sure a replacement part is even available and at what price. Thank you. Susan susan.eng@


Hi Susan, if the pin has broken off you can do one of two things, first, would be to find a local vacuum repair shop and take it there for them to look at. they may be able to look at the hose and fix it for you pretty cheaply. what ... Kenmore Progressive 20912 Bagged Canister Vacuum

Ordered a replacement motor for Hoover GUV garage utility vac L2310. It took months to receive. There are no installation instructions and the old motor was left with one of the dealers and lost. Any suggestions as to how to replace this motor.


... Hoover L2310 GUV Central System Vacuum

Where do I find a replacement for the hose that attaches to a Shark EP 3005 canister? The hose I have to the vacuum split.


Have you tried here > http://www.sharkclean.com/cgi-bin/livew/ ... Euro-Pro EP3005 Bagged Canister Vacuum

Fantom Twister Our Fantom Twister is not picking up dirt. There does not seem to be any blockage in the hoses and I replaced the hepa filter and the second filter that sits just below the canister where the dirt is collected. It is still not working. Any suggestions yuo have will be appreciated. William Moran


When cleaning everything change the main filter which it's the filter inside the yellow mesh holder. the filter number is 1010fs. One filter is 26.90 with s&h. This needs changing every 2 years.\015\012call customer service number above. ... Fantom Vacums FM741 Twister Bagless Upright Vacuum

Dyson dc14 How do we replace the belt one I removed it to clean hair from brushes? Can't get it back in place. Any tricks or suggestions. Craig Dittmar


Hi am i right to assume the belt is still in place ie in position around the drive wheel of motor? and you have removed the roller/brush only? and you now have difficulty re assembling the belt on brush and relocating brush into its holder ?? ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth


When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

No suction I've only had my vacuum for a couple of months and it seem I have a similar problem but there is no clear blockage. It seems like I don't have adequate suction that reaches the accessory hoses nor the main one. I'm not sure where to start. I've taken the darn thing apart but I can't see any obvious malfunction. Any suggestions?


If you have low suction at the end of the hose, then you either have a clog in the hose or a clogged filter. Take the hose off and drop something in it to see if it comes out the other end. If you have suction at the end of the hose, then the dirt ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce


I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum

I need a replacement hose assembly for the hoover steamvac jr. any suggestions where i might find the part?


Only through a Hoover warranty/ service center if still available. If not save your hose ends and find a different hose with adaptable ends ... Hoover F5411 SteamVac Jr. Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0748 seconds