Having problems with your Bissell 1622 Powerlifter Powerbrush Upright Deep Cleaner Carpet & A ?

Grinding sound Grinding noise from the unit when started, Lent to friend who owned many pets. Not sure how to diagnose and/or repair problem.

Answers :

You need to make a thorough inspection for debris and pet hair cloggin your vac. Could have ingested a load of kitty litter or....
Repair Help & Product Troubleshooting for Bissell 1622 Powerlifter Powerbrush Upright Deep Cleaner Carpet & A

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Grinding sound Grinding noise from the unit when started, Lent to friend who owned many pets. Not sure how to diagnose and/or repair problem.

You need to make a thorough inspection for debris and pet hair cloggin your vac. Could have ingested a load of kitty litter or.... ... Bissell 1622 Powerlifter Powerbrush Upright Deep Cleaner Carpet & A

Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and

Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a dyson dc07 with a malfuncitoning clutch diagnosed here on fixya. I've replaced the clutch and the grinding noise when the clutch is engaged for carpet and non rotating brush problem presists. This is after replacement of the clutch with a new part. Install of the new part went well and there are no otehr apparent problems with the unit. Ideas? The unit is only a couple years old and not used that much on carpet. For an expensive vacuum I'm not that impressed with it at this point.

Greetings from GoVacuum,\015\012\015\012If you have replaced the clutch already, then this can really only be one other problem, and that is the roller brush. If the roller brush's bearing have locked up, and the brush is no longer spinn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Saeco Odea Giro pumps the water but the internal spline or gear is not turning moving the ground coffee grinds to the point where the water can pump to the front exit lines so the water is pumped into the over flow resevoir. How do I replace the gear or check to make sure this is the problem. I want to replace this myself.. Also how do I get the unit apart it seems to be bullet proof. Is this a common problem.

It is a common problem if it is what I think it is. However your description is a little confusing. So the coffee does get ground up, but then has a hard time getting to the next stage of the process? Please clarify... And no water gets pumped th ... Vacuums

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

My dc24 has power makes the right noise but when released from upright gives a burning smell an trips the electric out . Is this a repairable problem? Do you think its covered by gaurantee?

... Dyson DC14 Bagless Upright Cyclonic Vacuum

When i turn on my bissell proheat pet it makes a grinding noise

... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My steam vac was working...i thought the dirty water was full but it didn't make the hi pitched noise now that i think about it.....now it is not sucking up the dirty water.....i checked to make sure it was placed right and can't visually find anything wrong....help! i have pet stains to vacuum up...this is only about 1 year old.....

\015\012The most common reason for lack of pick up is that the lid is not fully seated on the dirty water tank. Be sure to hook the two tabs on the front of the lid, and then snap the rear latch into place. Another reason is that the duct on th ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

We have a Russell hobbs power cyclonic pets 2000w vacum cleaner that seems to have lost quite a bit of suction, we have cleaned the filter and made sure there are no obstructions in the hose. We have only had the item for 2 months so would like some help with the problem. Regards Mrs D.Cook

... Vacuums

My bissell pro heat 25A3/64D9 series just started making a really loud grinding noise while on. Can anyone assist me in determining what may be wrong and how to fix the problem. Thanks.

... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a DC04 which is a number of years old and has started making an awful grinding sound, I'm sure it is the belt which I sprayed with WD40 and this helped for a couple of seconds but as soon as I recline the hoover it makes this noise but not when upright and using the hose. Does anyone have any ideas or how to change the belt? Thanks

You have to change the belt look it up with your local vacuum store. ... Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall

That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

Our Vax 2000 motor goes OK but it is starting to smell of burning and making a grinding noise. I haev taken the motor unit off and the sponge filter but still it persists. What is the probelm and the repair please

... VAX Appliances 2000 Canister Vacuum

I have owned 4 sebo uprite vacs. Every one of them has the same problem. Where the handle connects to the vac it break contact and shuts off and on. It seems the connection between these two parts is very weak. The only answer I get from my local repair shop is

Well you now know the error of your ways, don't buy another!The best fix is to remove the connectors and connect the wires directly together. ... Century 400 UVAC Vacuum

My Dyson dc-07 makes a loud grinding noise only on the carpet setting.The belt seems to be fine,and the brush spins normally.Do I have a potential clutch or motor problem?

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Noisy vacuum I have a eureka capture that I bought in april it's making a horrible high pitched squeal type noise, I have made sure my roller is clean, my filters are clean, i replaced my hepa filter and there are not any blockages I don't know what else the problem might be. Could you please offer other suggestions to fix this?

... Vacuums

Dc17 -too much pet hair around the belt gears

I was having the same trouble and it was driving me nuts.  I tried cleaning and it did not work.  Then I tore the brush assembly off and looked up into where the little tooth gear is.  I saw something that did not look right.  The ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.

... Windsor VS14 Versamatic Bagged Upright Vacuum

DC07 grinding noise

I had the same problem with mine, I took it to a repair shop. The problem is where the belt passes through from the brush and goes inside the machine. Move the belt over a bit and you will see that a plastic guide has been bent over and is pressing o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Loud Grinding Noise

Jhu ... Hoover V1 SteamVac SpinScrub Vacuum

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.

... Bissell Vacuums

My dyson C07 ANIMAL is making a loud clatter noise when I push the head down. I have removed the sole plate and the brush bar is cracked so I removed it, but I understand the clutch maybe a problem also from reading other people's comments..how can I tell if it's a clutch problem also? Or... could it be just the brush bar being cracked that's causing the loud noise?

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Horrible noise The same problem that has been the other people have experienced, I can make the noise stop if I switch to floors, but it doesn't work well on carpets. Has anyone been able to fix this problem?

It sounds like you have a blockage. Go to this at Dyson to look at your item in more detail. They have good support here for your item. Just copy and paste into your browser.http://www.dyson.com/support/help.asp?product=DC17-ANIMAL&ar ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a power groom dual cyclonic vacuum. It is less than a year old. The belt is fine, It is not clogged. The brush rotates and it has suction. The problem is that it has the most awful high pitched noise now. Truthfully, the noise is so awful it makes you nauseus. What is the problem?

... Bissell 3920 Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0493 seconds