Having problems with your Bissell 1622 PowerLifter Upright Vacuum ?

I have a Bissell 1622 PowerLifter Powerbrush carpet cleaner and it will not dispense water/cleaner and it will not suction. I have tried just running hot hot water through it and it still won't work.


Answers :

Repair Help & Product Troubleshooting for Bissell 1622 PowerLifter Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bissell 1622 PowerLifter Powerbrush carpet cleaner and it will not dispense water/cleaner and it will not suction. I have tried just running hot hot water through it and it still won't work.


... Bissell 1622 PowerLifter Upright Vacuum

My sunbeam water cooler model #YLR2-5-67H3 has been sitting unplugged for 3 years. I moved, plugged it in and put a water bottle on top and water went all over the floor. I unplugged it, (read the instructions on the front, duh) and it still leaks on the floor. What should I do? I put it over the sink, emptied it, checked the drain plug, tried running a glass full of tap water through each tap. Only the room temperature one would work.


One of the rubber connecting hoses inside it has dried and aged so the pressure of the water from the bottle made it burst.\012\012\012You will need to open it, find the defective hose and replace it - a 2 hour relatively easy job. The hardest ... Sunbeam Vacuums

Water i run hot water through my machine but still the water comes out more often than it should ?


... Dirt Devil Easy Steamer Upright Wet/Dry Vacuum

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?


Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Steam cleaner stopped sucking up water. Motor still running. It's blowing hot air. I checked the seal on the water recovery tank and it appears ok.


Steam vac won't **** up water ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My bissell aroma pro had a horrible burning smell then stoped sucking up water. the motor was still working and water was being feed out just not back up. the machine was hot as i had already cleaned 3 rooms in the house. i let it cool down but the burning prob returned as soon as i turned it back on. any help would be great thanks


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

My steam pocket mop seems clogged. Steam does not come out of the mop head. The clog appears to be in the rectangular mop head. The triangular head still works fine. I've tried soaking it in hot water and soaking it with cleaning solutions. They have not worked. If I blow into the connection piece, no air goes through. That's what leads me to believe there is a clog. If you can help, please do. I like the product and haven't been able to use it for awhile because of this. Thanks.


I had the same issue with the rectangular mop and corrected it by disassembling the tube from the rectangular piece. There are two screws that will need to be removed in order to get access to the connector. Once the connector is removed from the rec ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have a Bissell Proheat 2x cleaner which has worked perfectly on every occasion. Today I filled the machine as usual with water and formula and switched on, the motor ran, the lights were on and the brushes rotated but upon pressing the spray trigger no water or formula was released. I have cleaned the jets underneath and also followed instructions to release any airlock. It still wont release the water/formula. What else can I do? Thanks Charles


Please check the following with liquid in both tanks.\015\012 \015\012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\015\012- ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I HAVE A BISSELL PROHEAT 2X HEALTY HOME, IT WORKED JUST FINE THE LAST TIME I PUT IT UP. YESTERDAY, I NOTICED THE FLOW GAUGE WAS NOT SPINNING, SO I CHECKED AND SURE ENOUGH NO WATER WAS COME OUT. I CHECKED AND ALL THE TUBS AND EVERYTHING ARE IN THE RIGHT PLACE AND HAVE LIQUID IN THEM. HAVE TRIED PRIMING CLEANING THE BRUSHES RUNNING HOT WATER THROUGH IT... HELP


Have you made sure that the tanks are seated properly and the red \012(or black) auto-load gaskets are in place. \012Check the bottom of the Water Tank and the Formula Bottle to make \012sure each has a red auto-load gasket attache ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have the hamilton beach espresso maker, 40715 and I've had it since this past christmas. The past few times I've used it, it takes a long time for the espresso to brew, and now it's barely brewing just a few drops every few seconds. I've tried running water through it and cleaning all of the pieces. It still isn't working properly.


... Vacuums

The brushes don't turn. It runs and dispenses shampoo and water and sucks it up but the brushes stand still.I cleaned them and filter etc still doesn't work.


There is a plastic shaft on the back of the block brush (spin scrubbers),\015\012 these wear out or break. You may need to replace the block brush. Or if the shaft is not broken it could also be the Turbine Gear. This is \015\012what the block bru ... Hoover F7220900 SteamVac V2 Upright Vacuum

I purchased the Shark Steam Mop less than a year ago and I have used it about 8 times and now it is not working. It will not steam. The light on the front is on and you can hear it tryng but it will not get hot and steam the water like it should. I think it needs to be replaced with a Warranty Item for free. It is still under warranty.


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Water wont come out when handle pressed to do floor or out of nozzle for upholstery cleaning smells hot when trying to get it to work could this be a belt


Yes it most likely is the belt ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Why wont the brushes spin? I have had this machine for about 3 years and it has always worked great, tonight the brushes will not spin at all, it still sprays and sucks up the water. We took the brushes off and were able to spin them by hand


In this machine there is no belt. The brushes actually spin by vacuum and in the turbine assembly there is a small wheel bearign which rusts out. You will need to remove and repair or replace the turbine and gear assembly P/N should be 43191009 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Pickup water wont pickup the water after putting it down very little comes up into the tank .it worked fine when we baught it but after not useing it for some time it worked now it wont **** water up at all can anybody help.


The clear shroud covering the front of "hood" has two sheet metal type screws at the bottom in front of the brushes, these two screws also hold the little straight brushes ( one on each side) in place. I found one of these screws had broken it's plas ... Hoover F6020-900 SteamVac Upright Vacuum

I have a Bissel 9300-C 0714 BC Carpet Shampooer. It was working great and all of a sudden it stopped working. It still sucks up dirty water but it does not spray water onto the carpet. I can get it to spray water through the smallest hand attatchment but not through the large hand held piece on the base of the machine. I really hope you can help me, I am a dog groomer and I really need my machine to work properly. I can get it to spray water out of the smallest hand attatchment but that's all t


The spray jet has become clogged from the soap.... just clean it out. same thing happened to my attachment. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a bissell pro heat model 7901-B that has power but no water circulation. I was told that the previous owner used it without water and that she couldn't get it the power on. I bought it off of her and cleaned it out and now the power works, but there is no water circulation. The brushes run and heater works, just can't seem to get it to circulate water. Thankyou for your time, Don


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Hoover SteamVac Plus 1200 upright hot water extractor Water/carpet cleaner applying o.k. Suction on the "floor" does not work. Suction on the hand tool works somewhat, but water is not collecting in the bucket. There is suction coming from the floor but water is not going into the bucket. It does not appear to be clogged because I can feel with my hand that air is flowing from the floor. The water is not being sucked into the bucket.


... Hoover Vacuums

No water I have a Bissell 1694 and it is not ejecting the water cleaner solution out of the front of the machine. The belts are ok. The two nozzels and hoses are not clogged and do not have any holes. I think the pump still works because water still comes out of the brush tool.


It is easy to take the top off. Mine has just 6 screws. Then you can see all the tubing and parts. For example, you can unclip the nozzles and see if water flows. Try blowing through the nozzle to see if it is plugged.\015\012\015\012Some people s ... Bissell Powersteamer 1694 Upright Vacuum

I have a GXCFD GE Smartwater hot, cold water dispensor, everything works but the hot water, doesnt light up, or get hot. any suggestions


If there is no hot water coming out from your instant hot-water dispenser, check the following to find out the prolem and fix it :\015\0121.Power: Under-the-counter hot water dispensers are plugged into a standard wall socket that suppli ... GE Vacuums

I have a bissell proheat carpet cleaner model 8910-w 08019c.the machine will not add cleaner or water to the floor.I have cleaned all the filters with it still will not work. I have checked all the fluid levels and reseated the tanks and still can't get it to work. What else can I do?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My shop vac stopped working while vacuuming i looked at everything i could look at and still wont work tried several other outlets checked cable still nothing


Staring from the failrue of the power cord,the main plug,t he main switch each of the sections must be tested for continutiy before we can conclude.\012SInce it is clear case of power failure the voltage must reach the motor,if not back trace t ... Shop Vac Vacuums

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!


Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

I have a shark steam mop and it will not get hot and steam the water so I can clean the floor. The green light works on the front and that is all that works. It there an element or something inside that heats the water. It is under warranty they should have to replace it.


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0704 seconds