Having problems with your Bissell 1672 BIGgreen Wet/Dry Vacuum ?

My machine does not work. It will not put out water or will not **** up water It will turn on only


Answers :

The pump is probably dead in the unit. you can try to turn it on without turning on the suction I believe. Providing your model has 2 switches you can anyway.
\012
\012the only other thing it could be is the solution tube maybe blocked, or not enough solution in the tank to draw from.
\012
\012a pump is approx $40-$60 just so you know.
\012
\012Let me know either way.
\012
\012Good Luck.
Repair Help & Product Troubleshooting for Bissell 1672 BIGgreen Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brushes won't turn on the bissell proheat 2X steam cleaner-I don't have the manual to see if there is a button I am not pushing to turn on the brushes. Also, do you put the clean water in the "bladder" in the tank? Sorry I am so dumb-this cleaner was given to me with no manual and I can't figure it out. There is a small tank on the bottom at the back of the machine, that says "formula here" and I don't know if that is where the cleaner goes or what that is for. The machine turns on just fine


... Bissell 8910 ProHeat Clear View Upright Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance


Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Electrolux epic series 6000 sr model canister...we put a new bag in machine but it wont turn on and the light is on saying the bag is full and needs to be replaced...we tried the on-off switch several times but it wont turn on...why?


... Electrolux Vacuums

Hi. I borrowed my friend's Hoover VC340 to clean my house. I was vacuuming when i noticed the cannister was full, so I turned the vacuum off, pulled out the barrell, and followed the instructions on the barrell to empty it. I put it back into the machine, but it wont turn back on. I tried different power outlets, but to no avail. any thoughts?


... Vacuums

Brushes run freely on the cog and I put on 2 new belts and new brushes on my Bissell Proheatx2 the brushes do not turn when the machine is running even if I have the handle in the relesed position


I know how frustrating it can be when the brushes don't turn when you're ready to clean.Here's a quick link to troubleshooting steps to assist you:\015\012 ... Bissell Vacuums

When I try to turn my clean solution tank upside down to put it on machine solution pours out the cap through a pin hole in spout cover that goes over the place where you screw it on.


... Vacuums

Our Dyson DC28 won't turn on. I used the machine earlier on today emptied the unit and put it back on charge. 5 hours later have gone to use the unit again, however now seems to have no power to i


... Dyson DC28 Animal Bagless Upright Vacuum

I have an old Janome sewing machine and when I plug it in at the power point and turn it on it sews without putting your foot on the pedal Can you help


I have to same problem as tony ... Vacuums

I have an Elna 2600. I'm trying to thread the bobbin, but it won't turn. I hear the machine on but the bobbin stays put. What do I do? I've rechecked the directions several times.


... Vacuums

The belt broke on my proheat, I got the replacement belt and got it put on, turned on the machine and it instatly broke the new belt. Any ideas why??


Sound like brush roll is jammed solid .Clean. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My machine does not work. It will not put out water or will not **** up water It will turn on only


The pump is probably dead in the unit. you can try to turn it on without turning on the suction I believe. Providing your model has 2 switches you can anyway. \012\012the only other thing it could be is the solution tube maybe blocked, or ... Bissell 1672 BIGgreen Wet/Dry Vacuum

Restrictive valve moments after starting the vac the red ball rises to the top and the machine quits sucking. I turn the machine off, the ball drops, I turn the machine on, the ball rises the machine quits sucking, I turn the machine off the ball falls, I turn the machine on........etc. What am I doing wrong? It works fine and then all of the sudden it starts the same stuff again. I thought it was because the retrieving container was getting too full or the cleaning soln container was not full e


The foam filter on the bottom of the tank lid is too far up. Pull it down so you have at least a 1/4 inch gap from the top. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Polti Vaporetto 1500 Unable to unscrew polti safety cap. ( nothing to do with steam as machine not turned on yet)


... Polti Vaporetto 2400 Canister Steam Vacuum

Lux 5000 put in new bag but when i turn on the


Here's how someone else solved the "bag full" sensor problem:\015\012\015\012http://www.friday.com/bbum/2005/12/08/silly-aerus-lux-5500/ ... Electrolux Lux 5500 Canister Vacuum

Hi i bought a fog machine from target and it told me to let the machine heat up and once the light turns red to turn it on so it can produce fog but its not producing anything. do you know what could be wrong?


Wish I could help, I bought two of them from Target and they both worked for about 15 minutes then stopped producing 'fog'. ... Vacuums

The machine backs out of the dock, then proceeds to turn in circles, stop and then start turning in circles again. I have cleaned all of the sensor areas and made sure the bumpers were not stuck against the machine. Any ideas


... iRobot Roomba 560 Robotic Vacuum

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?


Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Cleaning Solution It really isn't a mechanical problem. I would like to know what kind of solution I need to put into my machine. I bought it used and if didn't have a manual and I can't recall what I was told to put into the machine. I hope someone can answer my question. Thank you in advance Phyllis Woodall.


Most any brand name carpet cleaning solution will work. I like ZEP from the Home Depot. Nice fragrance, low foam and economical vs. Bissell, Hoover, other appliance brand names. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

The brushes on the Hoover All Terrain Steamvac won't turn. However, when I try to turn them manually they will turn. So, why won't they turn when the machine is turned on?


Some vaccums have a belt on the brushes. might need a new one if it does have the belt ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th


... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1315 seconds