Having problems with your Bissell 1692 PowerSteamer Upright Vacuum ?
Brush not turning and no suctions !
\015 My powersteamer model 1692-c .\015\012When the switch is on, motor is running but no brush turing and suction.\015\012checked the belt but OK. Gear which turns the belt is not turning !\015\012pls help\015\012\015\012park\015
If the cogs on the belt and brush roll are ok, then probably the cogs on the pulley are worn off, or the pump isn't turning, is the flat belt ok? If all of this is ok, then replace the pump, part #\015\012\015\012\015\012\015\0122107181If no suction, is the black oblong gasket on the top of the clear window. It seals the gap between the tank and the window, no suction if it is gone. Also should be a red plastic screen on the edge of the tank lid, it may be clogged.
Repair Help & Product Troubleshooting for Bissell 1692 PowerSteamer Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
No suction When I turn the vac on it sounds ok but there is no suction and the brushes don't turn. Alot of air does come out of the two exhaust vents and the brushes will turn manually.
Hey, how are you ?\015\012\015\012here are a ew things that could be causing you sorrow\015\012\015\0121.) Check your vacume to ensure that it isnt clogged anywhere\015\012\015\0122.) before your compressor and aft ... Hoover F6020-900 SteamVac Upright Vacuum
Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.
The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums
I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom
Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.
Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums
When vacuuming carpet with the electric power brush it will ocassionly , go to zero suction mode and shut off the brush. I have tried to cause it to happen by playing with the joint areas ( handle to tube and tube to power brush) without sucess. When the problem does occur I just turn the suction back on and power up the brush again at the handle controls.
You gave a good start to giving us good information to help you with solving this problem-- But I need a little more information:It sounds like you have the Electric Motor driven Power nozzle/ Floo ... Miele Blue Moon Bagged Canister Vacuum
Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.
Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums
Dc11 dyson the brush head turns very slowly but when i take brush head cover of (the yellow part) and put my hand over the suction inlet part the brush head turns really fast. Have cleaned out collection chambers eg the hoover bag have washed the sponge with the little pictures of taps on it what now . thanks alan
I have taken the brush heads off and pulled all the hair out of the small gap between the chrome shaft and the plastic gear housing. Then a small amount of 3-in-1 oil into that gap to lube the internals and just a little through the air intake on th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
I had to empty the canister and when I put it back on and turned on the vacuum, the suction does not turn on. The brushes are rolling and the attachment suction works fine. Any suggestions?
... Eureka 431A Optima Bagless Upright Vacuum
No suction at floor brush. Plenty of suction in the tube that goes to the joint just before the 90 degree turn to go from the handle to the brush area.I lowered the handle so that the tube was straight and probed. The tub is clear. I cann't find the manual at home or on line. The Hoover.com site is useless in searching for a manual.
Are you sure the brush roll is turning. If not sometimes it will appear to not be sucking. Take off the bottom plate, then you can get to the brush roll and belt.\015\012 ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum
The brush does not turn but the belt seems very tight. There is also suction at the top of the hose but no suction at the brush head. I have removed ever pat that I can tell that comes off. Any suggestions?
DC07s have two drive ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Hoover upright bagless vacum.motor runs, brush turns, no suction through hole behind brush roller. however there is suction going out of dust cannister filter flap to motor. what could possible problems be?
Sorry to read about your problem, I hope this helps you out.you have a clog between the brush and bagI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Bissell cleanview - brush not turning. can i fix it...vac is 3 mos old? brush turns freely by hand. suction is good thru hose.
Put a new belt on it ... Vacuums
Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o
Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.
Generally, the problem is that the belt is not running the brushes. This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed. This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
My Henry has great suction but as soon as I put the orange brush head on,there is no suction and the brush is not turning. Any ideas
Take apart and check all bearings ..belt more likely gone ... ... Numatic Henry Extra Canister Wet/Dry Vacuum
I have a Kirby G series diamond edition. There seems to be no suction when I turn on the vaccum. The bag inflates, but the roller does not turn. It has a new belt and the roller brush is clean. Any suggestion on what I might do to increase the suction and get the roller bar moving?
THE IMPELLER LOOKS SHOT.. 25 QUID FOR NEW ONE,,LIFT THE LID AND TURN THE ROUND PIN AND CHECK FOR RIDGES ROUND THE WHITE IMPELLER,,IF NONE THERE THATS IT,, HAPPEND TO ME TEN MINS TO FIX GEORGE ... Kirby Ultimate G Bagged Upright Vacuum
'eureka whirlwind lite' vacuum - brushes turn but no real suction
... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum
Dyson hose suction strong...when using the brush bar no suction available. Have looked to see that all airways (u-bend) are clear. When engaging the brushbar the brushbar turns but no suction to floor.
Hello,There\012 are several things that this could be. Probably the most common problem\012 that we see when customers come in with this problem is actually a \012fairly simple problem to fix. Here are just a few things that this could\01 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Brush not turning and vacuum not suctioning
It probably needs a new bag or could be clogged. ... Eureka Capture Upright Vacuum Vacuum
Dyson DC08 turbo brush won't turn but have suction in tube
Hi Cathy,I'm sorry to hear you're having difficulties with your DC08's turbo brush. As you've already checked the machine for blockages and washed the filter, I'd encourage you to get in touch with us directly so we can provide further assist ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum
No suction & brush will not turn when power
Check your belt. It is broken or stretched out. Replace the belt first. Should be your answer ... Hoover Elite Rewind Bagless Upright VacuumVacuum
Brush not turning and no suctions !
If the cogs on the belt and brush roll are ok, then probably the cogs on the pulley are worn off, or the pump isn't turning, is the flat belt ok? If all of this is ok, then replace the pump, part #\015\012\015\012\015\012\015\0122107181If no suction ... Bissell 1692 PowerSteamer Upright Vacuum
Brush turns....suction low! Attachement works, no
Check for a blockage between brush and entry into dust chamber, if something has not made it's way to the dust chamber could result in low suction1 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
Vacuum brushes won't turn. It still has suction.
That means that you need to replace the belt that turns the roller brush. They naturally stretch and wear and you should replace this belt yearly. Here is the belt you need and the manual which has instructions on how to change it: ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Hoover Steam Vac - Brushes not turned, no suction power
The Brushes not spinning is most likely is caused by seized bearings in the turbine, requiring shop service (easy fix). The suction issue can be caused by the standpipe seal missing or lower recovery tank not on properly, on some models missing front ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum