Having problems with your Bissell 1697-7 Powersteamer Pro Deluxe Vacuum ?

How do you replace the pump belt?

\015 How do you replace the pump belt on a Bissel Pro Heat carpet cleaner?\015

Answers :

To install a new belt you need to unplug the unit first and flip that bad boy over so you can acess the bottom of the unit. You will need a phippilps or torks driver to remove the scres towards the front where the brush is. Once you pull all this out the belt will be attached to the brush and a small pin in the back. It is really simple. Hope this helps out.
Repair Help & Product Troubleshooting for Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I Have two questions concerning my AIRVAC AV2500 Red Series Vacuum System. How do you replace the light in the floor power head sweeper and can you replace the permanent fabric filter? We had the system installed in 2004 and the light in the sweeper head just went out and can not find any manual on line on how to replace it. The filter if not torn but avter 6 years it probably needs some kine of cleaning or replaced even though it says permanent. Any help would be appreciated. Jim McCluskey


... Vacuums

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef


Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

Bissell Powerwash Proheat. model 1698-j, 220-240v, 50/60Hz, 1200-1400w. Motor stopped suddenly (ident label specifies type Ametek 119464-02), supply inline fuse at motor ruptured, fuse replaced but motor sparks like an angle grinder at armature and blew replacement fuse. Where can I obtain a replacement carbon brush set for the motor. UK based


... Bissell Vacuums

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I am replacing the hose on my kenmore canister 11622612200. i easily replaced the handle end of the hose, but cannot see how to replace the end that goes into the canister. can you tell me how to disassemble the canister end for the new hose? many thanks!


Open the canister and locate the hose intack. There is a plastic retainer which slides over the end of hose and is secured to the body of the canister with a few screws. Remove the screws and pull the retaining ring up to release the hos ... Vacuums

Battery replacement I would like to replace the battery on my handheld Black and Decker 9 volt battery Dust Buster. But where is the battery? How do I remove the old battery so I can replace with a new battery?


... Black & Decker CHV9600 Handheld Vacuum

I own a old Bissell Big Green Cleaning Machine and am looking to replace the inline fluid/vaccum pump. The pump has an Eaton logo and is model CP7. I have not been able to find a replacement at your site. Could you tell me if one is still available or where I might find a replacement?


I just saw one on USAVacuum.com It's about $29 ... Vacuums

My mother purchased a replacement hose assembly for a Bissell ProHeat 2X and the part was shipped without any instructions... While I am pretty handy, my issue is with the supply tube, and I cant figure out how to accomplish the replacement, and as its not MY vacuum, Im hesitant to start taking things apart.I just need instructions to replace the entire hose assembly.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Dear Sir or Madam, I own a black 23 x 47 x 7 mm Rowenta lighter. It has a screw on bottom that I cannot remove. What is it hiding ? Is this lighter refillable ? Is there a flint to replace ?. I've found on your site the following : "By jbbiii on Apr 06, 2009 Father died and left me a Rowenta lighter purchased in Stutgart in 1952. It has a screw on bottom with spring to replace the flint, but I cannot figure out how to open the bottom to replace the cotton wadding which I can see through the hole


Hello \015\012The flint should be near the striker.Or the thumb roller,usually below it.\015\012As old as it is you may not see it beacause its worn down.\015\012\015\012Maybe taking it to an antique store or a smoke shop woul ... Vacuums

I need to purchase new blades for our 52" Jericho IV ceiling fan, Model 166315. I went to home depot in Harrisville, UT and they said that we would have to contact you and they didn't have ANY replacement fan blades in stock. HOW COULD THAT BE WHEN THEY HAVE HAMPTON BAY FANS ALL OVER THEIR LIGHTING SECTION? What kind of a business are you running when one can't get replacement parts? Our fan is making noise and I want to replace the blades. How hard can that be? By-the- way; I hope you no


... Vacuums

The rotating sweeper on my Electrolux Discovery II isn't turning. Can I assume there is a belt that needs to be replaced? Also, how do I get at the sweeper unit to replace the belt? Finally, where can I find a replacement belt? Thanks!! Dewey


... Electrolux Vacuums

Where can I get a replacement glass lid for Rival crock pot model #3100/2? The one listed below is out of stock, but, even if it were, it will not fit my model. Any suggestions? "Buy-it-now-store.com" lists: CURRENTLY OUT OF STOCK, NO ETA. # Rival Crock Pot Lid Replacement Glass for 3.5 Quart Rival Slow Cookers - $5.99 Rival Crock Pot Slow Cooker Replacement Round Glass Lid Cover # Works with Rival Crock Pot Models: 3100, 3101, 3102, 3103, 3130, 3133, 3120, 3250 # Approximate total


... Vacuums

Power nozzle of my S3670 does not work (vacuum itself does work), the headlight bulb in the nozzle is broken. This happened in the past several times - we would bring the vacuum to service center - I don't know what they did other than replacing the bulb. I decided to go to ACE and buy replacement bulb myself, replaced the one in the nozzle - this did not fix the problem. I don't see any fuzes or anything in the nozzle. However, the manuals says to "Use only HOOVER part no. 27317307, which is a


... Hoover S3670 Bagged Canister Vacuum

I need to replace the plug in cord on my rowenta iron. I would replace but I paid $130 for iron and my cats have chewed on the cord so I thought it "might" be a simple replacement.


This is the second cat-chewed-a-wire question tonight.\015\012\015\012The only thing to do is to replace the entire cord. You could cut out the chewed section and splice it with **** connectors and electrical tape, but you have a nice iro ... Vacuums

Belt replacement i am trying to replace the belt on my kirby g4 and i can not get the rooler off to replace the belt. if you could tell me how to do this it would be great.


Lift the light bulb housing up and you will find a latch that will rotate to release the front agitator housing and remove it from the machine. On the bottom of that housing, there are two latches that secure the bottom plate that covers the roller. ... Kirby G4 Bagged Upright Vacuum

Replace belt i need to replace the belt on an upright dirt devil 086310 vaccume but do not have a manual and can not find how to open the assy to replace the belt


On the bottom, there should be a few screws to remove to remove the plate covering the brush roll. However some may have screws on the top housing to remove the top. ... Vacuums

Hello, I have a Hoover quadraflex Powermatic central vacuum system Model # s8099-031 that requires a new replacement 35 ft hose...I have contacted Hoover and they do not know where to buy a replacement hose for this model. I live in Canada. Any idea where I can get a replacement hose for this system? Thanks kindly, Tammy


Tammy, no info re your location, so I''l try this.Your Hoover hose is shot because it was made of rubber.There are new swivel handled, tangle proof lighter hoses made of vinyl which will last much longer and can be adapted to the old Hoover hea ... Vacuums

Need to replace lower handle and pivot as it broke off. I got replacement but no instructions how to replace.


... Vacuums

Replacement wheel I broke the wheel on my bissell upright model 3760 and need a replacement wheel and possibly an associated side molding. I can't seem to find replacement parts such as these- any suggestions?


The rear number is 2036627, there is no side casing, you would have to replace the whole back, which Bissell isn't making avaiable. But o get the wheel, you might try bissell.com and see if you can order direct, or try a local repair shop to see if ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!


... Kenmore Vacuums

Replacement motor I purchase a replacement motor for a F5897-900 Hoover SteamVa Motor part # 43576197 or 27242051. The replacement motor has three electrical connectors + ground were as the orginal has two electrical connectors + ground. Do I ingnore the the thrid connector and hook up the wires to the same connectors as the orginal or do I have to do some rewiring.


The manual only show one wire from the motor going to the switch, the other going to the cord, then the ground wire. I would wire it the way your old motor was, could be that some models maybe were 2 speed and the other wire would be used for that. ... Vacuums

Need to replace power cord and can't find how to open canister to replace


I had the same problem and could not find the other screws. You need to pry off the power cord retraction button, you will find two more screws under there. It's pretty easy after that!!!! ... Kenmore 22612 Bagged Canister Vacuum

Shark vacuum nh15 replacement pet hair power brush replacement


... Euro-Pro Vacuums

Im looking to replace the motor mines when bad looking to replace the burn out motor


... Hoover F5906-900 Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0376 seconds