Having problems with your Bissell 1697-7 Powersteamer Pro Deluxe Vacuum ?

Motor running good but the water isn't coming out of either the bottom or the hand held tool


Answers :

Make sure your recovery tank is pushed down snug,somtimes it just need to prime itself,I had the same problem with my hand held tool, and that seemed to do the trick,after it pushed down,turn on power then wait about 10 seconds then turn on heater. I hoped this helped.
Repair Help & Product Troubleshooting for Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Motor running good but the water isn't coming out of either the bottom or the hand held tool


Make sure your recovery tank is pushed down snug,somtimes it just need to prime itself,I had the same problem with my hand held tool, and that seemed to do the trick,after it pushed down,turn on power then wait about 10 seconds then turn on heater. I ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Pro heat 2x no water coming out carpet part / hand tool either


In case any of you are still trying to figure this out... I took mine into a repair shop and had the pump replaced for $66. The repairman had 6 other machines in his shop when I bought mine in. He said the pump goes the minute it runs dry, so if yo ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell PROheat 2x carpet cleaner the water doesnt come out of it either from the bottom or the tool can it be plugged somewhere?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

We have a Eureka 71B Hand-Held Vacuum and it looks like the belt broke. I removed the two screws at the bottom that should release the housing that holds the belt. However, the housing still does not come apart. Any advice? Thanks.


There's a 3rd screw hiding underneath a plastic shield. You'll have to drill or cut off the covering but then it's pretty easy to deal with. ... Vacuums

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a


You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

I cannot charge my two year old electrolux pronto. I purchased a brand new hand held vacuum for it, but even the new one does not charge. When I plug in the cord nothing happens. If I turn on either the long handle or the portable unit within the long unit, the blue charging light comes on for a few seconds, then out. This tells me that the circuit is intact without a broken wire somewhere. I took it all apart carefully and could see nothing broken or out of place. On re-constructing it, it


It must be the charging transformer. We have already ruled out the vacuum unit. Unfortunately the transformer is not a serviceable part, and will need to be replaced. ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

My F7458-900 leaks water when using upholstery tools I do have good suction, but water comes out fast on the bottom of machine.


This sounds like the hose connection valve is bad. The part is about $12 -15. I would take it into a qualified repair shop for repair. This type of repair is worth it. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have been trying to register on line and can't get in. I am having problems with my WindTunnel powered nozzle it doesn't want to run and I just got this as a gift May 1st. The power hand tool works but not the other one and I know all the connectins are good


It will have a years warranty on it. Take it in to a warranty repair shop and tell them that yo got it as a gift and when. ... Vacuums

Checked all the hoses and didn't find a clog. Water will not come out of the bottom nor the hand tool. What else could be wrong?


Check the red gasket on the formula bottle. if it is not on the end of the bottle but is stuck in the bottom of the hole than it will create a air leak. ... Bissell 9200 Upright Vacuum

Rug doctor hand tool will not spray ...but it will vaccum....what can I do to get the hand tool to spray again ....tried another hand tool and that didn't work either ....help


... Vacuums

I have a Hoover SteamVac F5914-900 SpinScrub... The last time I used the hand tool attachment, it worked fine. Just tried to use it again, and now I only drips of water will come out of the hand sprayer, if that. I have tried prepping it for up to 15 seconds like the manual says... no luck with that. Also it is making a big puddle on the floor, probably because the brushes on the main unit keep spinning when I am trying to use the hand tool which I dont think they are supposed to do? Can a


The brushes can be turned off on most of them via a switch on the hood. There shouldn't be water coming out onto the floor unless you are pulling the trigger at that top. You probably broke this when attempting to use the tools. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Have water at the hand held but none out the bottom


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have the Bissell Proheat (7901) It will pick up water and the hand tool works fine. I noticed that the red indicator stopped spinning. Then I noticed no water was coming out. If I put down water using the hand tool, the vacunme will pick it up. When I called Bissell they had me do something with the indicator. When it didn't work they said take it in for repair.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

No solution is coming out the bottom but comes through the tools


Dear Sir:Remove hose, and remove any debris from hose assemblyInset again, and put new solution in the tank.God bless you. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Hoover SteamVac Plus 1200 upright hot water extractor Water/carpet cleaner applying o.k. Suction on the "floor" does not work. Suction on the hand tool works somewhat, but water is not collecting in the bucket. There is suction coming from the floor but water is not going into the bucket. It does not appear to be clogged because I can feel with my hand that air is flowing from the floor. The water is not being sucked into the bucket.


... Hoover Vacuums

When I try to disconnect the hose in order to use the hand held hose with an attachment, the dust from the bottom flies into the air. How does this opening get blocked off to ensure the dust enters through the attachment and not the bottom?


It is a matter of Physics. It seems like you have it running when you change the hose. ?? That's a no-no.Basically you will have o take it apart until you know how it works or wont work ... Bissell Vacuums

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

I have a hand held vaporettino steam cleaner ....the appliance is working but the water container has been dropped and has a hair line crack in the base and leaks the water from the crack ....I am looking to either buy a replacement water container or to buy a new S/Cleaner if you could let me know of a supplier either in the UK or Spain


... Polti Vacuums

When using the floor configuration, I can't get the trigger to cause a spray of either water or cleaner. When using the tool configuration and the hand device with brushes etc, the spray works well with the hand trigger.


The trigger on the handle for tthe floor configuration has become loose or broken. When you squeeze it, the action pulls a rod that runs down the length of the shaft and goes into the base and allows the water to spray. You need to check and make sur ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Water leaks out the bottom of vac have new tank but the water still comes out the bottom while running like it is automatic no control


Hi Steve I have the same problem can you help if you were able to fix? ... Hoover F7220900 SteamVac V2 Upright Vacuum

We have the Kenmore progressive direct drive (bagless) and have had it for about 3 years. We have taken good care of it, and paid quite a bit for it hoping that it would last for a good long time. It has started making a noise that seems to be an overflow air type of noise coming out of a bottom air outlet opening for when the air flow is blocked. We have looked into clogs, changed filters, and the whole works, to no avail! Quite Frustrating since I love this purple vacuum! The machine started


There has to be a clog or block somewhere - if the motor works, it should work did you try a wire coat hanger to go up in further where you cannot see?Bets regardsCk ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

The cleaning solution stopped coming out of the rotating brush but still comes out of the hand held vacuum hose.


If you can check where the vacuum hose where it is connected their might have dirt in the opening to the rotating brush,or it is glogged,clean with a wire and it will be ok ... Bissell SpotBot Robotic Wet/Dry Vacuum

I got a Dirt Devil Versatile 3 in 1 design hand vaccum for a birthday present This has a suction type of cleaning. I would like a hand held lightweight vaccum cleaner with a roller type brush and cervice tool. I would like to clean carpeted steps. I want to return the above cleaner and get a voucher for another cleaner.


... Dirt Devil Vacuums

No suction in the hose for the hand held tools at all


Hi I had the same problem and my Hepa filter was clogged. You may wanna check that.\015\012I hope that helps. This is my 4th Windtunnel and I hate this one also. I loved all the rest. ... Hoover U8361-900 WindTunnel 2 Bagless Upright Cyclonic Vacuum

Modelsc505uk steam is staying in the main unit and not coming out of the hand held floor unit


... Euro-Pro Shark SC-505 Handheld Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0535 seconds