Having problems with your Bissell 1697-7 Powersteamer Pro Deluxe Vacuum ?

My Bissell carpet cleaner model #1697-W will not dispense the cleaning solution and will not **** the water back up--also need to know how you get to the belt on the machine?

Answers :

The drive belt for the pump is located under a cover on the front right side as you look for the front of the machine. Just lift it up and the belt will be obvious. If it is not sucking then make sure that the dirty water tank is empty and that all the filters are clean and the front of the machine is not clogged with fibres, dirt or hair. Also check pre and post motor filters and clean them if required. Then check the mix control is working OK to allow fluid to flow out of the machine and not switched off. Bissell's are simple machines.
My bissel cleaner will not **** the water back out of the carpet. Is this a defect in the machine or am I doing something wrong?
Repair Help & Product Troubleshooting for Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bissell carpet cleaner model #1697-W will not dispense the cleaning solution and will not **** the water back up--also need to know how you get to the belt on the machine?

The drive belt for the pump is located under a cover on the front right side as you look for the front of the machine. Just lift it up and the belt will be obvious. If it is not sucking then make sure that the dirty water tank is empty and that ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I can't get the vacuum to **** and can't get to the point of the clog. The pieces don't come off. Also need to know how to get the filter piece off the machine.

This link is for the manualhttp://www.dysonmedic.com/PDF%20docs/dyson_dc18_owners_manual.pdf ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.

Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m

... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Hoover Max Extract LS F6056900 Hand Tool not working / Cleaning Solution I need to know what I need to get in order to have the hand tool work on this model. Also, what cleaning solution is best for pet stains? Tried cleaning, pre-treating with Spot Shot and towel and/or scrub brush, then cleaning, still doesn't work. PLEASE HELP!!

... Vacuums

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?

Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

My vac. pet attachment exploded in my hand! I have talked to a debbie on the phone for a pick up of this machine, but I want to know whats going on with this certain machine! because it hurt the palm of my hand under my right thumb bad and I need someone to get back with me today!!!!!! SHERRI ADKINS P.O. BOX 1502 CHAPMANVILLE W.V. 25508 HOME #304-855-8868 CELL#304-784-6456

... Dirt Devil Vacuums

I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me

Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums

Took apart my cleaning brushes and all on my bissell spotbot i need diagram of how to fit the head part back to the machine. I had a problem with the auto not working i have fixed that problem just need to see so that i can get it back togoether. I assembled the whole wheel back but cannot caonnect it to the machine LOL

... Bissell 1200A SpotBot Pet Robotic Vacuum

Bissell Proheat - I need the manual - how do I get the water container back into the machine? I took out the tank and filled it up with water but I cannot get it back in. I need a manual or a picture of how to do it. thank you, ruth

Http://www.bissell.com/images/UserGuides/7950_1204.indd.pdf ... Vacuums

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum

I need to change the motor in a vax 6131 but i don't know how to get into it to get the change it? I also need to get into the motor assembly housing to change a part but can't see how it comes apart!!

On the handle there is one small pozidrive screw, remove and orange panel comes away revealing powercable securing bar. Remove 2 screws and this reveals a 10mm headed bolt. Under label on top of handle there is another small pozzi screw, undo t ... Vacuums

I have a genie hoover and would like to know how I get the purple bit back onto hoover as I emptied the filter and I can't get it back on need help fast???

... Vacuums

Cleaning Solution It really isn't a mechanical problem. I would like to know what kind of solution I need to put into my machine. I bought it used and if didn't have a manual and I can't recall what I was told to put into the machine. I hope someone can answer my question. Thank you in advance Phyllis Woodall.

Most any brand name carpet cleaning solution will work. I like ZEP from the Home Depot. Nice fragrance, low foam and economical vs. Bissell, Hoover, other appliance brand names. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

How do I get a replacement belt for my DC 17? We sucked something up and broke is so I do not care if it costs anything, I just need a belt for the beater. How do I get one? unfortunately my wife also through out the old one with a part number on it,....

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Need a replacement drive belt for my hoover lark u4043 not sure about last no. it's an old machine, but this one is in perfect condition, minus the drive belt. my local vacuum specialist says they can't get them anymore. where can I get one or a suitable alternative?

HiAs you know the Hoover Lark was more or less a rebodied Hoover Junior. The U4043/ (are you sure its not U4034?) model should use the same round drive belts as the Hoover Junior 1346 so youre looking for the old rubber ring type belts which ar ... Vacuums

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi

Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?

First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

Floor Attachment I took off my floor attachment, but now the belt seems to be off and I can't seem to get it back on right. I can't use the attachment and I don't know why it's so hard to figure this out. They say, just turn it to belt off, but when i turn it it lift's it up and can't line up with the belt off label. Then, when I turn it the other way, it's off. So I've been trying to pull it off so when it lines up with belt off, it's off. But the I turn it the other way and it's still off a

Try this,\015\012\015\012With the floor nozzle off the machine spin the belt lifter around until the red arrows match. If you look at the side that attaches to the vacuum you should be able to see the belt up on the hook. If is not on t ... Kirby Generation 3 Bagged Upright Vacuum

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th

... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

The rotating sweeper on my Electrolux Discovery II isn't turning. Can I assume there is a belt that needs to be replaced? Also, how do I get at the sweeper unit to replace the belt? Finally, where can I find a replacement belt? Thanks!! Dewey

... Electrolux Vacuums

Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]

The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum

I need to replace the belt I bought a new belt and I can't get the belt back on

On this pagehttp://www.totalvac.com/videos/kirby-vacuum-cleaners-videos.htmthere is a video at the bottom on changing belts on a Kirby ... Kirby Generation 3 Bagged Upright Vacuum

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]

Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Owner/user manual Before my sister died she gave me the little grren machine model 1425 turbo brush with heat. That is all I know about it as she did not find the manual and now no one knows where it is and I really want to get it working and learn about it, as I know she loved it. so I really need a manual. thank any one that can tell me if it is on line or something.

Http://www.bissell.com/images/UserGuides/1400_206.pdf ... Bissell 1425 Little Green ProHeat Handheld Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1082 seconds