Having problems with your Bissell 1697-7 Powersteamer Pro Deluxe Vacuum ?
The unit stops sraying out liquid after one pump
\015 It will work through one pump, and then it just stops spraying out liquid. If I turn it off and on again, it will spray once, then stop again\015
This has o rings and do need to be replace is the suction is lost
Repair Help & Product Troubleshooting for Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The unit stops sraying out liquid after one pump
This has o rings and do need to be replace is the suction is lost ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
My shark steamer has stopped working after a year of having it (I have already replaced one, I'm a idiot!). My problem; however, is that it will steam, but the steam stops traveling through the actual "mop" part. I plugged it in, wait seconds and start pumping, but the steam builds up until it's hard to pump. I had to press the button really hard for the bottom to come off and it shot off like a rocket! I tried to stick something through the tubing, but it did nothing. What am I doing wrong? I
\012\012\012Hi,Here\012is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it\012may not be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce
I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum
Vax 6131 water pump had stopped working on taking apart it had over heated and plastic casing had melted in one place,obtained new pump from buy spares which matched old part fitted and reasembled but pump does not run ,is there any internal fuses ? Or any thing else to replace
... VAX Appliances Vacuums
I am putting my bissel 8910 back together and behind the motor there is a black 3-way tubing connector. One side goes to the pump discharge, one side goes to a tubing going to the right rear wheel (facing the unit from the front) I don't know where the third side goes to. I do not seem to have another tubing for this one to go to? Maybe it is lost or ?
Hi, its hard to know what its for without seeing it. The best way to test this is to start the machine and vacuum a part of the carpet/ floor. Then let me know wht the vacuum is not doing. This will narrow it down. Please, get back to me. This sounds ... Bissell 8910 ProHeat Clear View Upright Vacuum
Hoover S3765 I have a Hoover S3765 (serial # 040600024465) and the unit stops working for no apparent reason. The light on top of the unit goes off when it shuts down, so I don't believe it's a problem between the hose, the tube and the floor unit. Sometimes I have to let it sit for over one hour before it will come back on. I've tried different electrical plugs too. Still won't turn on. Any ideas or suggestions? Thanks
If you light and nozzle motor both go off at the same time, you might have a bad power cord. Mine had this problem which I could verify by jiggling/twisting the cord near the strain relief on the nozzle. It would go on and off as I did this. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum
Looking for users manual for anti-bark dog collar (citrus spray) model name/no: innotek ssb-300. This is a replacement for my original unit which stopped working. Petsafe sent me the manual for the original unit again...not this one, which is slightly different. (categories below do not apply...could not 'un-choose' from the product list??!! - sorry) Darlene - Edmonton, Alberta Canada
Innotek has a manuals download site hereA citrus spray model manual is ... Vacuums
DC44 Used right out of the box for about 10 minutes, then I took a break and plugged it in. Went to use it again and after 1-2 minutes it just stopped. The green light on the charger unit is lit but the one on the handheld part is not lit. Is it just charging or did it stop working??
... Dyson DC44 Animal Cordless Vacuum
The roomba or I robot will upon pressing the start button go around in circles, than starts to goin one direction, than stops and goes in a circle. The unit is clean and the unit reset. Bill
Is the front bumper **** in? ... Roomba Vacuums
Roomba My Scheduler started making a "grinding" noise every now and then until one day it just started grinding and then stopped (I could restart the unit, however it repeated the grinding and stopping). I have checked the wheels and all of the gears appear to be in good order. I have a hunch the brush motor may be stripped. Any opinions? Thanks: RAnderson
Hi!\015\012\015\012Further investigation (running diagnostics mode) revealed the impeller (in the dust bin) was out of whack. I got another dust bin from EBAY and replaced the impeller and motor. Unit works fine. ... iRobot Roomba 4210 Bagless Robotic Vacuum
The Karcher B502 pump will run when not connected to the water supply, one connected the pump will stop. Fues ok / Power cable ok
I have a Eureka Central Vac CV1601b. The motor does not stop unless the Unit is unplug from the electrical outlet. Any Idea?.I removed the control unit to check if there was disconnected wires or burnt wires. Everything look normal. The circuit board does not show area that overheated. There seem to be 2 relays. Likely one of the two went bad. What do you think.
If the unit is relay controlled, there is always the possibility that when the unit was turned on, the relay contacts welded themselves shut making the power button ineffective. \015\012\015\012If you're familiar with relay pinouts, with ... Vacuums
I have a Hoover spin vac # 7410-900 the brushes don't spin but i can hear the pump running , checked the brush block stem thats fine the unit feeds water and soap. but i have no vacuu.me or brush movement getting ready to rip the turbine out to check it . the weird thing is it worked fine and then just stopped
... Hoover Steam Vac Dual V w/ SpinScrub Vacuum
My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current
I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum
I have a one year old Beam central vac. It has supervalves. The handle (connected to the hose stopped turning on the unit. The handle still powers the brush but no longer turns on the suction?
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=566201 ... Vacuums
I bought one of these units last year and it worked great for about 9 months and then it stopped brewing coffee. Not sure what is wrong. It will not heat the water to make the coffee. Any idea as to what could be wrong?? Thank you. Pierre
Hi,Either the heating element is completely corroded with mineral from the water or the heating element has gone bad...If it is not heating at all there is some kind of electrical problem or the element is gone bad... ... Vacuums
Altrev, I have an ODC325 Black&Decker spacemaker coffeemaker on my boat and it stopped working this weekend although the hot plate still gets hot. I suspect it is the thermal switch as you described (I hear a click when I switch the machine on but nothing happens and the heating element does not kick in). I would be very happy to receive one or two of these 14 spare switches you mention so I can repair the unit. If still available I would appreciate hearing from you how we can do the transact
We don't sell parts individually on the site here.... was it some other solution for another person you saw about the switch? I don't believe there really is a part called a thermal switch... there is a thermal fuse but if the hotplate gets hot I wo ... Vacuums
Please clean Roomba s brushes warning will not stop after brushes have been cleaned Unit shuts off after one minute of cleaning
Clean the yellow brush bearings. Then run the Roomba without the dustbin, so that you can watch the brush while the unit is cleaning. Is it turning? If not, call customer support. 877-855-8593. Have your Roomba with you; they will want information fr ... iRobot Roomba 570 Robotic Vacuum
I bought Roomba 560 and love it. It didn?t come with a lighthouse so I bought one on Ebay. When I put the batteries in it the green light on top flashes 5 or 6 time very quick and then stops, it doesn?t flash after that. When placed in front of the Roomba in either mode, virtual wall or lighthouse it doesn?t direct the Roomba. The question is, is there a process to marry the two units together or do you think the lighthouse is defective? Thank you Gary
... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum
My first proheat lasted four years so I bought a new one. After I used my Pro Heat for only the fourth time my first issue occured, the gear on the pump that runs the brushes came off, so I had the one from my old proheat, I just changed the gear spindle that is screwed to the pump and fixed that problem but now it will not pump water. That is why I bought a new proheat, I could not get the old one to pump even after a new pump and made sure all lines were not cloged.
Is your new machine a 2X or like the old style proheat? ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Power Unit VX475 Stops
Received a call from NuTone Tech Support in respone to my telephone call to them about overheating Power Unit. Apparently my VX475 Power Unit was supposed to have been changed during manufacture with a modification to motor circuit/motor parts. NuTon ... Broan-NuTone VX475 Bagged Central System Vacuum
I need a relay board for a Nutone CV 450 12.6 amp dual motor vacumn unit. Where can I locate one? Part #??? Unit will run by itself, then shut off. Unit wll not run at all. It has a mind of its own. Crossed a couple of wires on one of the relays and the unit runs smooth as silk. I assume its the relay, but can't locate part number.
Why not just replace the relay? Part number 1094117... ... Broan-NuTone CV450 Central Bagged Central System Vacuum
I have 2 JWIN DVD players, one stopped working, Hooked up an older Jwin and does not have remote. How can programed the one that does not have a remote to the the relote from the one that stopped working.? Thanks
One cannot change the program of the the remotes that come with the DVD player. They have no learn capability, in other words they do not have a EEPROM chip in them which can be erased and programmed any number of times. The cost does not permit it. ... Vacuums
Attachment problem used a new unit w/attachment for 5 minutes...dispensed solution in a powerful triangular fashion. Then the fluid quit dispensing out of the attachment nozle amost like the pump quit working. Primed the unit several times w/ no success. checked for clogs. can't tell if the floor portion is "pumping' or just dribbling solution onto the floor with the trigger. can see no leaks at this point. unit worked for about 5 minutes on apholstery
Make sure everything is filled and secured tightly, if this a new unit it should be something simple ok, also check where machine folds down that the solution hose is not being pinched its right behind the dirty water tank ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
I have a proheat 2x, and the pump will only spray water for a few seconds when unit is turned on, then nothing. The attachment is the same way. I think this is the pump failing, and the unit is only over a year old. How much would a pump cost? If this is the problem.
I just had my pump replaced for $66 and the repairman said this unit is notorious for this problem. He had 6 other units in his shop when we came in. Make sure you keep your clean water tank FULL, as he said the pump fails as soon as it runs dry. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum