Having problems with your Bissell 1697-7 Powersteamer Pro Deluxe Vacuum ?

My power steamer seem to be putting down water and scrubbing but it's not picking up the water it puts down. Also, it doesn't seem to be using any of the cleaning solution

Answers :

Trythe following suggestions to see if you can get your machine suctioning properly:
\0121) Remove the Tank-in-Tank Assembly and place your hand over the motor intake valve. This valve is located next to the Floor Nozzle gasket (at the top of the Floor Nozzle window) and behind the SmartMix Bottle. If you feel vacuum-like suction at this area, your suction power of the unit is working but air is escaping at some point. If there is no suction at the motor intake valve your machine will need to be inspected by an Authorized Service Center Technician.
\0122) It is possible the Floor Nozzle on your machine is inserted incorrectly. This would directly affect the suction of your machine. Please follow the directions below for removing and replacing the nozzle.
\012Before starting, please be sure the machine is unplugged and the machine handle is reclined.
\012To remove the Floor Nozzle window, first detach the Phillips head screws located at the base of the nozzle. Then, remove the Tank-in-Tank Assembly. Next, pull forward at the top of the Floor Nozzle window to release the tabs of this window from the receiving holes of the machine. This window is designed to allow access for cleaning.
\012When replacing the Floor Nozzle window, please be sure the tabs at the TOP of the nozzle are properly inserted into the receiving holes provided. If you do not have the tabs in place properly, the suction power of the machine could be affected.
\012Rotate the window down into place and replace the screws.
\0123) Ensure that the Ready Tools knob (diverter knob) is in the proper setting and the valve opens and closes freely. Ensure the black foam gasket is in place under the valve.
\0124) Check to ensure the Tank-in-Tank assembly is seated properly and that it is not full of dirty water. (If this tank has a drain cap, make sure it is in place and that it has a black o-ring).
\0125) Check the float and baffle to ensure they are properly installed on the Tank-in-Tank. The larger square portion of this part should be below the clear baffle of the tank with the red flag portion of the float resting on top of the baffle.
\0126) Check the Tank-in-Tank and lid for damage. Is the lint screen clogged? Make sure the lint screen is in place on the tank lid and not placed into the motor duct. Also, clear the holes on the lint screen.
\0127) Check to see if the upholstery hose has suction. If the hose has suction and the floor nozzle does not, check the diverter valve to see if it opens and closes freely. This can be seen through the Floor Nozzle window as you switch the diverter knob from the floor to tools setting.
Repair Help & Product Troubleshooting for Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My power steamer seem to be putting down water and scrubbing but it's not picking up the water it puts down. Also, it doesn't seem to be using any of the cleaning solution

Trythe following suggestions to see if you can get your machine suctioning properly:\012\0121) Remove the Tank-in-Tank Assembly and place your hand over the motor intake valve. This valve is located next to the Floor Nozzle gasket (at the ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate

Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like i ... Vacuums

Bissell will spray water when set to water rinse, but as soon as it is set to light, normal, or heavy cleaning, there is no spray. I have tried priming but to no avail. I put plain water in the solution tank to test without ay success. It is like it loses it's prime whenever you try to use a solution mix. Once you set it back to water rinse only and go through the priming steps, it is OK. Any help would be appreciated. Thanks.

Please check the following with liquid in both tanks.\012 \012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\012- Check for ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My brushes on my hoover streamvac will not rotate. I removed and cleaned assuring that the filter was also cleaned. The only different thing I have done is to insert the upholstery attachment and removed it after use (didn't work so well) suction seemed weak. I am also noticing that there is air being blown out of sides where the dirty water container is. (don't recall that in the past).

... Hoover F5900-900 Upright Steam Vacuum

Where is the clean water tank on a dirt devil spot scrubber? Is there an additional attachment for using this. I got it at goodwill and can't figure out where to put the cleaning solution.

... Vacuums

Bissell proheat 2X, model 8960. The shampoo tank does not seem to work, all I get is the water when cleaning. Also the first time I used my shampoer one of the belts broke. This is the 2nd cleaner I have bought. Was hoping this one would last longer. Cleaning this model is a real pain, surely there is a better why.

... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I was in the middle of using my vacuum when it quite on me. I tried multiple things including letting it cool off for a while as I was using it to vacuum my car outside and it was pretty hot. I also dismantled it according to the directions and looked for blockages and didn't find any and lastly I cleaned out the brush and put it back on. I am out of solutions. The vacuum is not that old; we have only had it for a few months. Any assistance would be appreciated. Thank You, Karen

Hi the problem you are more than likely having is with the wires that go into the vacume they are not that secure and do work loose.now if you remove the cylinder that you empty, now you see where the wire goes into the back of the vac, w ... Dyson Ball DC24 Bagless Upright Vacuum


Water goes on the left side and the collection tank is on the right. I suggest the Bissell soultion it runs about $10 ... Bissell Vacuums

I have a Bissell 7920 ProHeat and only used it 4 times and the brush on the bottom has stopped spinning and when attempting to spray solution the flow indicator doesn't spin and nothing comes out. I have looked at all of the belts and they seem fine. I have also removed and cleaned the heating unit. Still nothing. Any other ideas?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My steam pocket mop seems clogged. Steam does not come out of the mop head. The clog appears to be in the rectangular mop head. The triangular head still works fine. I've tried soaking it in hot water and soaking it with cleaning solutions. They have not worked. If I blow into the connection piece, no air goes through. That's what leads me to believe there is a clog. If you can help, please do. I like the product and haven't been able to use it for awhile because of this. Thanks.

I had the same issue with the rectangular mop and corrected it by disassembling the tube from the rectangular piece. There are two screws that will need to be removed in order to get access to the connector. Once the connector is removed from the rec ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have Bissell ProHeat 2X 9300-M that I tried to use again today. Is does not dispense solution when turned to Floor Cleaning, when switched to Hose it seems to be working fine. Brushes and suction are working as well. Soap and water containers are full. I took off and replaced tanks, waited to prime the pump multiple times without success. Not sure what is going on.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I used it to clean up a latex paint spill, stupid i know, but had no choice, now it seems to be putting out less water, is this fixable?

There are two spray tips up behind the brush.\012Check to make sure the spray tips are clear. \012If paint got into them it could reduce the spray.\012If you need further assistance call BISSELL Consumer Services.\0121-800-237 ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

I have a Bissell Steam Cleaner that is not sucking up the water when cleaning. I used a full container of water and when it was empty I emptied out the water, only to find very little dirty water in it. I noticed the window, as i used it, seemed like it wasnt sucking up the water. I took the plastic cover off to clean it (it didnt look very dirty in the first place), an i noticed that the grey plastic flap was on but not moving up or down. I thought there may be dirt in it that prevented it from

... Bissell Vacuums

Recently our Vitapur water cooler has not been dispensing water. The problem is the water is freezing in the upper reservoir. We have tried unplugging the unit overnight & turning it back on at the minimum cold setting several times which has not worked. We have also used the Vitapur cleaning kit to clean the unit, which also did not help.

The problem is a comon one and simple. You just need to replace the themostat.\015\012Good luck ... Vacuums


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

When I was putting my new rug shampooer together and the directions said to press the trigger and the clean surge button until I heard a snap, I did just that many times and never did hear a snap so I thought it had likely happened and I didn't hear it so I proceeded to fill the solution tank and get busy but no solution came out so I used the clean surge button instead and got the job done (I think). Can I continue to use it that way or is there a way I can get it to snap and use it the way it

My husband figured it out and it now works great! Thank you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a

You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

My Bissell proheat 2x model 9200 is not dispensing cleaning solution. I hold the trigger and the carpet doesnt get wet at all. i poured water on the carpet and it sucks it up. the cleaning solution does mix with the water but it not being dispensed on the floor.

Hi, \015\012when last did you service the machine?\015\012\015\012i believe should service the machine.\015\012try to open the machine.\015\012\015\012when opening make sure you notice where the part you are remov ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell Powerease Lighweight Deep Cleaner. (Shampooer) After I fill the solution tank with the solution and water, I put it in it's slot, but all of the contents just come flowing out. I have only used this machine twice and it worked ok. You are supposed to press the trigger and the solution sprays out and then release the trigger when you want it to stop. But like I said, now I just put the tank on and all the contents come flowing out. I don't know what's wrong or how to stop it.

... Vacuums

The water tank on my bissell proheat 2x is not keeping the clean and dirty water separate. I;ve checked the container and there doesn't seem to have anything wrong with it. Also when I switch the machine on you can see the "washing" action, after a few minutes this seems to stop - there is water and forumula in the machine. Only had it a year!

... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have an older model F6056-900 Hoover steamvac Spin Scrub Cleaner. My first problem was that I loaned it out to a friend. Anyway she ran over the hose (used for attachments) with her car. I tried using the cleaner for carpet cleaning this morning but when I tried to put the solution tank into place...its loose...won't snap back in like it used to. When I can get it somewhat in place the solution just complete drains out through the bottom fo the tank. The leak is where the small hole on the bot

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I suspect that "the thing" where the coffe is put in and the water pushes through is not clean enough. Water seems to go/come beside the "thing" I alsohave the feeling that there is coffee in the water tank where I suppose itt should not be. so howdoI clean the thing?

Put in vinegar and run a couple of brews vinegar only(not coffee) till the vinegar is clear when done,(use white vinegar)only so you can see when its clear,then run a brew of clear water to remove vinegar taste this will delime and clean out coffee m ... Vacuums

I have a hoover 3000 i have not used in awhile, and since I removed a large rug, I would like to use it again on my slate floor. HOWEVER, I cannot get it to pick up ANY water in the water recovery unit......it is dry, dry, dry. I have put in a new filter, cleaned the nozzle unit, the scrubber , and reconnected both the recovery unit and the water unit several times, but to no avail. I would like to get a graut attachment a well as replacement part, but since I can't get the basic unit to work, I

Have you made sure the plastic filter cover with the round hole in it that covers the filter is in place ( part # 59177096 ). This piece seems to get lost, and without it there is no pick-up. The other common problem is that the wheel assembly has be ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Bissell Quicksteamer I have a Bissell Quicksteamer that is about 5 years old. I went to use it today and hardly any solution was coming out. I could see it suctioning up what little came out, so I took it apart and cleaned it thoroughly. I tried to use again and no solution is coming out. Everything seems to being working just fine. Thanks

Here's a kinda kick yourself quick fix that might be helpful, I took my whole machine apart all the way to the motor to come to realize that the small rubber piece that cover the tip of the water container was jammed in the hole you sli ... Bissell 1770 Quicksteamer II Upright Vacuum

Poor cleaning I recently bought the Shark Steam Mop as I read mainly fantastic reviews. I was disappointed to find that it leaves a slight film on my dark hardwood floors when finished. I can wipe the film away with my finger and you can see foot prints if walked over. I also found that there are cloth streaks on my ceramic floors after drying as well. I followed all instructions, vacuumed beforehand, used distilled water even though my water is not considered hard, cleaned slowly, etc. I am wo

Hi,This type of problem usually is not he fault of the Shark Steam Mop.The problem is the old residue left on the floors by other cleaners.Here is a tip that I wrote that will help you out with that problem... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 2.1543 seconds