Having problems with your Bissell 1697-7 Powersteamer Pro Deluxe Vacuum ?

Changing belt how do you change the belt on the power steamer there is nothing on bissells webiste i need to change the one on the sie not the rollers


Answers :

Take the water and solution tank out of the machine. turn it over an on the left hand side you will see a red clip with a screw in it. take out that screw. flip the unit back over and take off the belt access cover by sticking a straight screw driver down into the slots and popping the clips to release the cover. tilt the machine to the side and using your finger wiggle the red plastic piece down out of the way. the beater bar on that side should be free. make sure both belts are in good shape because the belts run the beater bar and the second belt runs the water pump.
Repair Help & Product Troubleshooting for Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Changing belt how do you change the belt on the power steamer there is nothing on bissells webiste i need to change the one on the sie not the rollers


Take the water and solution tank out of the machine. turn it over an on the left hand side you will see a red clip with a screw in it. take out that screw. flip the unit back over and take off the belt access cover by sticking a straight screw dri ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums

Need to change a belt on my Hoover Concept One Power drive


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=766023\015\012Generic problem for all Vacuums\015\012Need to change a belt\015\012Posted by gentilly on ... Vacuums

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it


The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

I have a Broan Nutone central vacuum. The power head seems to stall unless you lift up on the handle. I think I may need to change the belt but cannot find a place to purchase one to see if this is the problem Model number BN180 type 1


You are correct, you need a new belt. You can find belts for the Broan BN180 at www.vacbelts.com. ... Vacuums

Need belts I am in the middle of cleaning my carpet and need a power belt and roller belt. Who sells them locally. 30127 Powder Springs, Ga


If you local repair shops don't have them, I am sure they can order them for you. Just have to check you yellow pages, also under Sew and Vac stores, most offer service as well as sales. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh't start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat


It was overheated that is why it worked downstairs after cooling off. ... Miele S548 Bagged Canister Vacuum

I just bought a Hoover Power Drive Concept Two Electronic vacuum from the thrift shop. It only needed two belts and seems powerful. But i don't understand what the small red button on the handle marked "Release Drive" means. Thanks for any insight! Anything else i need to know about this machine? Is it a good one? Are there high-performance bags available for it?


The U6311-903 is a self propelled vacuum. The the small red button will stop the handle from moving back and forth, which makes the machine go foward and backwards. The red button disengages the self propelled feature. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

I think i need to change the belt on my vacuum, there seems to be a loss of suction when pushing the vacuum. Where can I get one and how do I change it?


How do I fix a broken belt on my vacum ... Eureka 4700A Maxima Bagless Upright Vacuum

The roller has stopped rotating and I wanted to see if the belt needs changing. I cannot find out how to get to where the old belt is located.


Remove the bottom to find the belt. There is usually a spare in the compartment. I think there is 8 or 10 screws.\015\012\015\012Thanks for your interest in FixYa.com\015\012 ... Oreck XL21 Bagged Upright Vacuum

I need to know if roller brush is supposed to turn it doesn't if it needs a belt pleasr show diagram or video how to change


... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Hi guys, I have a bissell 9400 2x proheat with a fault. When you turn on the machine it trips the RCD in my house and makes a poping noise, i am a little technical so i had a look inside. The pcb under the handle was damaged with burn marks i unpluged this and tried again and the machine powered up, don't think the rollers moved though. What do i need to change roller motor,pcb?? Help please!! Regards Russ


I've seen the same problem in one of these we had in for repair. The pcb in the handle is involved with controlling the roller motor. The problem is with the motor. In my view, this machine is a triumph of design over practicality... The motor is loc ... Vacuums

I have an old upright hoover vacuum. I need to change the belt but can't figure out how to get to it. The bottom plate over the roller brush comes off but I can't get anything else off to get to the other end of the belt.


Model no. req ... Hoover Vacuums

Belts I have a bissell power steamer pro deluxe and I need to change the belt and I dont have a manual here with me to see how to do it. Please help. model # 8804 07266c


Http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help/Upright_Deep_Cleaner_Repai ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Belt?! hello, I need to change the Eureka Oxygen Canister Air Driven Upholstery Tool's Belt (model 5860Avh), but I don't know which one to get? any help please? Best, Pierre.


You will probably have to order it online. ... Vacuums

I need to change the belt on the shampooer. the shampooer doesn't come apart like the vaccuum unit. i can't get the brush off so i can put a new one on.


This will help...\015\012\015\012http://reviews.ebay.com/CHANGING-THE-BELT-ON-A-KIRBY-G3-G4 ... Kirby G5 Bagged Upright Vacuum

Roller and belt changing need schematics


How to change the belt on the Bissell Clearview? ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Hi. I have a Sebo X4 and need to change the roller brush, but don't know how to get the old one out. Can anyone help, please! Thank you.


Here's a demo video for changing the brush, from the Sebo site.\015\012\015\012http://www.sebo-vacuums.com/video_download.aspx# ... Sebo X4 Bagged Upright Vacuum

I need instrution on how to change the belt on my kirby 4 power


You have to be more spicific on the model but: if you take off the front nozzle by loosen the nozzle lock, make sure the name kirby is horizontal, loosen the latches at the back of the nozzle un hook the rugplate located at the bottom of the nozzle. ... Kirby G4 Bagged Upright Vacuum

My Kirby G4 won't turn on. Everything is engaged as I normally do it, nothing is wrong with my power outlet, changed my hepa bag to a brand new one...


It could be a few different things. First make sure the emptor tank on the side of the unit is pushed all the way closest to the unit. ck to see if light comes on (that will tell you if you have power to the unit.) if so It is an internal problem. Or ... Kirby G4 Bagged Upright Vacuum

I need to change the belt that drives the power brush


Here is a link to the belts you need and a manual you can\015\012view:Bissell Carpet Cleaner Belt and Manual ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Weird noise i have a eureka the boss and i am getting a weird noise figured bag was full needed to change it so i did. Noise persisted so i checked make sure nothing was caught in the brushes. I even checked the belt it was fine replaced with a new one.Still the noise is there help me I am out of what else to check.


Squealing ... Vacuums

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1330 seconds