Having problems with your Bissell 1697-7 Powersteamer Pro Deluxe Vacuum ?

Changed belt, now its not working

\015 I changed the belts , put it back together and it will not **** the water up off the floor\015\012\015\012need schematic of machine\015

Answers :

Check the 1690 manual provided , there should be some picture there, models are almost the same
Repair Help & Product Troubleshooting for Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Sudden loss of suction. Using a dirt devil upright. Checked the belts that were changed recently and working. Changed the half full bag. No change. Checked for blockages and as far as I can see there are none. The blower is working as much as it ever was I think but I;m stumped.


R u sure there is nothing cought in the hose? ... Dirt Devil Featherlite Bagged VacuumVacuum

My Vacuum DC-17 has just quit sucking. It has been making quite a racket since I had the belt changed at a repair shop several months ago. I was told that the belt was a new design and figured that was why it was making so much noise. it seemed to work fine, was picking up dirt and all, but today, when I started vacumming, I noticed it was not sucking air either with the belt engaged or not. My vacuum is approx. 5 years old.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My question earlier today referred to a Kenmore Progressive upright vacuum. Your answer suggested that I change a belt, if the reset button did not work. Does a direct drive really have a belt? Regards, Jim Buckley


Direct drive does not have a belt. It is a shaft with gears. What is wrong with your vaccum? Maby i can help. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

We have the 3910T model. I am trying to get the height adjustment to work. I had taken apart the portion to change the belt and for some reason the height adjustment is not working. Is there a diagram on how to have the knob engage the other part?


... Bissell 3910 Bagless Upright Cyclonic Vacuum

Hi,My agitator brush won't run on my hoover S3590, I changed the belt, that didn't work. I don't see a possible cause in my book except replacing the belt. I think there could be a short, the brush will come on sometimes when pulling back and slightly lifting. Any ideas would be great and can I fix it myself? Thank you for any help, Bobbie


Hi Bobbie\015\012Take apart the electro floor head if you can and inspect inside - it may well be that there's clogged dust preventing the brush from turning and also check both sides of the actual beater bar as thread and tangled hair can often lead ... Hoover S3590 Bagged Canister Vacuum

Changing fan I changed the broken fan in my eureka 1934A. Put the cover back on and reattached the belt and when I went to start it, it wouldn't work. I took the cover back off to see what was going on and it looked like the motor was running in reverse of what it had been. Is this possible?


My solution is one that only works if the vacuum is a spare... To get mad at it and throw it in the garbage... \015\012\015\012My thought though on what the problem actually was... Seeing as where the vacuum came from and what the problem ... Eureka 1934 Bagged Upright Vacuum

Oreck xl commercial spits out dust on bare floor but work on carpet. It is about 15 years old. Bag has been changed. Brushes are spinning so belt is working. Started about 2 weeks ago. HELP!


It might be that the beater brush is spinning when you tip it up to look at it but slight pressure of it contacting the floor is enough to stop it.\015\012If it were my machine I would remove the beater brush and clean it as best I could, paying part ... Oreck XL Ultra Bagged Upright Vacuum

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?


Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Changed belt, now its not working


Check the 1690 manual provided , there should be some picture there, models are almost the same ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Changed belt, now its not working


Need schematic of machinereplacing the brush drive belt a item that looks like a valve dropped out and i need instructions as to where it belongs ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

The brushed on my steamvac Dual V F7227 are no longer working. We have pulled and cleaned the brushes, and the filter, but the brushes still will not come on. I saw a reply to one person that it is the belt. If so... how do I change it?


Greetings from GoVacuum,The Hoover SteamVac's are notorious for this exact problem. There are several things that can be causing this probelm.First, what you'll need to do is take the brush block out of the machine. To do this ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

I have owned my kirby sentria for 2.5 years and have had no problems until now. The vacuum still works but I cannot lower it all the way down or the light will turn off and it will start to smell like something is burning inside. I use it on the 2nd or 3rd setting with no problem. I have changed the belt and cleaned all the hair and strings that were on the roller but it still has this problem.


Kirby has a 3 yr back to base guarentee so contact ur local rep or kirby direct and thy will sort it all from there, hope this helps :) ... Kirby Vacuums

I have a Hoover self propelled WindTunnel vacuum( Model U6425-920) that stops in the middle of cleaning. I have changed the flat belt and I'm still experiencing the problem. I usually have to wait an hour or so b/4 it would work again. Any advise?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=632298\015\012Generic problem for all Vacuums\015\012I have a Hoover self\015\012Posted by thjunk2007 o ... Vacuums

Ive got a dc07 dyson just changed the belt on it as i had to since then it isnt picking anything up at all nothings clogged up had it to bits and put it all back together again properly. The hose is working when i take it off its got plenty suction but when i run it along the floor it picks absolutely nothing up any ideas that i havent thought off. Thanks


Sounds like the hose underneath has become detached. Have a look and if its not that come back to me. Also can yo9u check your U Bend is still on as these can come off. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Bissell powersteamer powerbrush starts up and then i pull the triger and water starts then stops. i cleaned the bottom of the tank by taking it apart and even had a different tank and both of them did not work. changed belts???


Tried to find out about this problem, and ran across this recall on the net:\015\012http://www.consumeraffairs.com/recalls04/2005/bissell.html ... Bissell Powersteamer 1694 Upright Vacuum

I have a Fantom 500 DX and it seems that it doesn't pick up anything anymore. It looks like machine is working well, but it doen't pick up. I would like to take to the repair guy, but I don't know where to find one. Machine is good, it might need jsu some maintenance. Please advise. I live on Long Island, NY. PLease advise. I changed the belt about 6 months ago, but all other parts are original.


The type of bagless that has sharp turns in the hose and plastic parts are easy to become stopped up. You have to follow the path of the air flow to find the blockage. ... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

How to change a drive belt the brushes are not turning but the motor works


OK, here goes... NOTE - any use of the words LEFT and RIGHT assume that you are looking from the REAR of the machine. NOTE ALSO - the machine has two toothed belts, it makes sense to change both while you're at it. Inciden ... Sebo X4 Bagged Upright Vacuum

The roll brush will not turn when on floor. Too much pressure stops brush. Changed belts and still not working


Turn the belt inside out. This problem stems from a design flaw in the mechanism that turns the hoover from bare floor to carpet. After taking it apart I realized that the spring that pushes the belt tight (to make roller spin) is not any where nea ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

I have a Bissell PROheat 2X shampoo carpet cleaner and the brushes stop working. i have changed the motor and checked the belts. everything is fine. any ideas?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

How to change a belt....rollers are not working...model #4337 eukeka 11 amps


TAKE THE SCREWS OFF THE BOTTOM AND PULL THE ROLLER OFF INSTALL NEW BELT ... Eureka Vacuums

Bissell Big Green Machine just stopped working in mid-clean. Have emptied tank, rinsed tank, checked belt, checked brush and still nothing. Have even changed outlets. Suggestions?


The motor could have fried or the wires have been shaken off the motor terminals. ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Beater bar The beater bar will not work. I have changed the belt and there is a lot of suction from the hose. Just seems like the base is not turning on


You may have a bad switch, one part of it is not turning on the brush roll motor. It could also be the brush roll motor. ... Clarke CombiVac 12 Bagged Upright Vacuum

I have a RICCAR 8900 - I have changed the belt and I think I did it correctly. Machine is running well, except the self-propelled portion isn't working. Vacuum only goes so far and then needs to be pushed, and yes I have it on the carpet setting.


Your vacuum is not self propelled. It is most. Likely something was not put back together properly when installing the new belt. ... Riccar 8650/8625 s Vacuum

Changed the belt on eureka model 8806, now my carpet heighth adjustment won't work


... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

I accidently ran over a sock while vacuuming underneath my bed and the belt broke (brush does not rotate now). I've always changed the belts in my vacuum cleaners, but the Healthy Home manual states that I need to bring it into a shop so that a professional repairman can change it. I find this ridiculous and now wish that I never bought it. How do I change the belt myself? PS I have already bought a replacement belt.


... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0689 seconds