Having problems with your Bissell 1697-7 Powersteamer Pro Deluxe Vacuum ?

No real problem

\015 I need a copy of the Manual. I just can't seam to find mine and I do not use the Bissell often and I for got if I put water in the tank, etc. Just how I do it.\015

Answers :

Www.bissel.com
\015\012has instruction manual
Repair Help & Product Troubleshooting for Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

It starting to put out a hot type smell. I have tried cleaning the filters real well and even tried to see if there was problem with the ozone filter. We have checked and could not find a jam. I know the hose has excellent suction. The vacumn works but the intelliclean sensors will not. It only takes about 15 seconds or so for the odor to start. Then it gets real strong and it makes my eyes water


Hi,The hot smell could be from the belt or the motor. Turn it on for a moment, turn it off, then flip it on its side and smell the belt that drives the brush. If that is where the smell is coming from, then your belt is burning up. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Over heating? My 10 gallon 4HP shop vac has started shutting off after about 30 sec. after I turn it on to use. It smells real hot after I shut it off. I have changed the filter and the bag, which did not solve the problem. Any suggestions on what the problem could be? It's only about 31/2 years old and I really don't use it all that much, mainly for getting up dust and cob-webs from my garage.


It sounds like you need to replace the motor in it . thank you for using fixya ... Shop Vac ShopVac 3 HP 2 Stage 10 Gallon--Automotive Wet/Dry Vacuum Vacuum

Good day, I took off the cover on a proheat upright, to install the suction diverter flap. Guy at the shop told me I had to do this but I don't think it was really necessary. Anyway, I am having a real job getting the cover back on. The shampoo mix piston seems to be causing the problem seating the two halves correctly. I see no obvious "right: way to put the piston back in. can anybody help me. Thanks Richard


Hey Richard. Turn the shampoo mix dial so the spiral is all the way at the top when you are looking at it from underneath. then, you want the piston to seat in the top groove of the knob. You want the piston's end that jets out to fit in the space ... Vacuums

I have a Hoover carpet cleaner F5358-900 It no longer sucks up the water. I have taken it apart from the top down and can find no real problem. (Although I am a woman!) The spray works and the scrubbing heads go around. Should I try to disassemble it further--I will need a special screw driver? Thanks, Jana


... Hoover Vacuums

No real problem


Www.bissel.com\015\012has instruction manual ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

The problem is that the cleaner is heavy to use and does not pull itself forward as it should. It has been back to the supplier 3 times but they have not fixed the problem. The LED's on the front flicker and I think it may be a problem with the sensor. If you have any info. on how the sensor works and where it is located it would be useful as well as any other suggestions to fix the problem please.


If it heavy then do some muscle work and body building ... Vacuums

My Riccar 1700 will intermittently lose power while vacuuming. I have had the vacuum for 4 years and this is the second time that I have had this problem. The first time the authorized repairperson said the problem was a dirty hepa filter. The second time, the repairperson put on a "pig-tail"(?) and said that he did not have a shut-down problem when he tested the vacuum in the store. I just picked it up from the store today, brought it home and the same problem occurred within minutes.


... Riccar RC1100 Compact Vacuum

Problems with the pd20000 dirt devil


... Dirt Devil PD20000 Stick Steam Cleaner

Not real sure what is wrong with my kirby.


I would say to replace the belt for the brush....kirby's have been known to go through belts.....also when i owned one within a year i think i went through 7 belts....try that and let me know what happens. the belts easy to replace. ... Kirby Ultimate G Bagged Upright Vacuum

The Shark floor stem cleaner Will not produce any steam. What is the problem? I have ahd the machine a year and never had any problem. the problem just started.


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Lately we've been having plumbing problems to where our washing machine floods up our bath tub and toilet. And it happens while we have the washing machine on of course. Another problem is that whenever we are taking a shower our tub starts to clog up and water starts pouring out from the bottom of our toilet. We had a plumber come by to root out our pipes just last week and it was fine for about 3 days. And now the problem is back and driving me crazy. WHAT IS WRONG AND HOW CAN I FIX IT??


Possible tree roots best thing is to hire a plumber with a camera snake ... M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum

I have owned my kirby sentria for 2.5 years and have had no problems until now. The vacuum still works but I cannot lower it all the way down or the light will turn off and it will start to smell like something is burning inside. I use it on the 2nd or 3rd setting with no problem. I have changed the belt and cleaned all the hair and strings that were on the roller but it still has this problem.


Kirby has a 3 yr back to base guarentee so contact ur local rep or kirby direct and thy will sort it all from there, hope this helps :) ... Kirby Vacuums

I posted my problem earlier today that I was having with my Bissell Little Green Machine not dispensing solution, but sucked up no problem. Someone said that the most common problem was a blockage. We put hot water in the reservoir for 15 minutes as advised and it still will not dispense. The fluid is now ''dribbling''so it is better. It is just not spraying. We are able to blow from the end and make bubbles in the reservoir which shows us it is not blocked. Any other suggestions?


Okay. I fixed this on mine. Undo the screws on the handle, right by the trigger. You pull the tubes off the little valve. Push on the button and see if you can blow through the valve. If not, push a pin around in the valve (with it pushed into the ... Bissell 1720-1 Little Green Wet/Dry Vacuum

Electrical problem I have an electrical problem with the above cleaner. My wife recently extended the power cable by yanking it out of the reeling mechanism too violently. The cleaner stopped there and then. I suspect that the cable has become disconnected inside the cleaner and I would be grateful for information as to how I can mend this problem. Nigel


May have broken the cord, in which case you will probably have to repace the reel cord asm. But you will have to take it apart to find out. Take off the bumper that gores around the cannister, there are 3 or 4 clips that hold the two halfs together ... Sebo Air Belt K2 Bagged Canister Vacuum

I have the same problem with intermitant power, however, it does not make sense that the problem is in the upper powerhead (which is what a repair guy told me) because-- when I use the other attachements it is fine. The problem only occurs when I use the carpet (big)attachment so that the roller will not turn. Couldn't it just be in the area where the bottom of the handle attaches into the carpet attachment?


You can test the auxiliary plug to the roller/beater attachment with a volt meter if you know how and take precautions. Check for 115-120 volts at the beater/roller attachment plug. If voltage is there and the beater/roller doesn't run, the proble ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Dyson animal won't start. Never had any problem with this vacuum. No apparent problem. No electrical problem with house or outlet. If there are some common things I could check/fix, things that might go wrong, I would like to check them out and get this machine going again.


Hi there, if the machine was running and cut out in use, this could be due to the motor overheating. The cause of this would be a blockage or a dirty filter. These checks can be found in the Support section on our website at www.dyson.com. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


You need to change the belt(s). You can find the belts for this model here. http://www.vacbelts.com/bissell-proheat-belt-combo-pack.htm ... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a H3000 Floor Mat The problem is it want pick up the water after the scrub clean the floor. What could be the causeing the problem?


You need a new brush block. ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC ... Bissell Vacuums

Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don't get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]


Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Clutch replacement I have a dyson DC7 animal that is having a clutch problem, I have the repair manual on how to do it, my question is what other things should be replaced while I have it all apart. ( ie belts, filters, etc? ) The unit is about 2-3 years old and this is the frst problem we have had with it


Go to http://www.youtube.com/watch?v=7_CtaFcc5HU to see how to remove clutch. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Leaking problem I have a leak in my water tank. It only leaks when it is upright. And sometimes it doesn't let the water out when I go to clean. What do you think could be the problem


I had the same problem and it was a crack in the plastic near the small rubber valves that let the water out. After having two tanks crack like this I complained to Hoover about the poor design and they sent me a new tank with a new design fee of cha ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Suction problem my proheat wont suction water out of carpet,,, it made a mess of my carpets now, any one no how to fix the suction problem?


The valve on the bottom of the water bucket is not being pushed up enough to allow the vaccuum to go through. Perhaps a part is missing but I used a small ball bearing and a car vaccuum cap to build it up and now our works but it is still a piece of ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

We own a dirt devil model 088600, and are experiencing a problem with the belt wearing away a section between where the belt connects to the brushes and the motor. There is a lot of plastic/rubber residue coming out from the vacuum. We have tried new belts only to find the same problem occurs. I noticed that the source of the dust is coming from the section between the brushes and motor, where there appears to be a section that is misshapen and melted. I looked up the schematic online and can't


If you are certain that the belt is seated correctly and the beater bar is nested in its holder and the cover of the assembly has been properly installed and you still see a contact area between the belt and cover, you should either: return the vac ... Dirt Devil Vacuums

I own a Hoover Steam Vac V2 deep cleaner with Auto Rinse feature. The Model Number is not available ex: was on the bottom of the machine and the sticker is completely worn off the machine. I am having a problem with the bottle you fill with detergent ex: this bottle is seperate from the main clean water tank. THE PROBLEM: The little plastic part that goes in the bottom of the bottle has an "O" ring ex: cone shaped with a spring.....it keeps falling out. Can you supply a part number for this


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=641300\015\012Generic problem for all Vacuums\015\012I own a Hoover Steam\015\012Posted by w_brennan on ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0361 seconds