Having problems with your Bissell 1697-7 Powersteamer Pro Deluxe Vacuum ?

I THINK THE SMART MIX PISTON IS INSTALLEDS WRONG

\015 I TOOK APART MY 1697 BISSELL STEAMCLEANER AND ALL IS WORKING FINE EXCEPT I DONT THINK I INSTALLED THE SMARTMIX PISTON CORRECTLY.IT SEEMS TO NOT BE CATCHING THE KNOB THAT CHANGES WATER ONLY TO H TRAFFIC OR REGULAR.I REASSEMBLED BUT NO SOAP WAS RELEASED FROM THE SMART MIX RESEVOIR.EVERYTHING ELSE IS FINE. CAN YOU GIVE ME ANY ADVISE ON HOW TO ALIGN BEFORE PUTTING COVER BACK ON ?\015\012 THANKS JOHN B.\015

Answers :

It has the rubber seal and the container releases fluid when it depressed.... bipolar lol..
\015\012
\015\012fill it with hot water and prime the machine.. don't use soap just try lear the lines.. always run hot water through your machine to clear the lines before storage.. and to maintain prime
Repair Help & Product Troubleshooting for Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I THINK THE SMART MIX PISTON IS INSTALLEDS WRONG


It has the rubber seal and the container releases fluid when it depressed.... bipolar lol..\015\012\015\012fill it with hot water and prime the machine.. don't use soap just try lear the lines.. always run hot water through your machine ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Good day, I took off the cover on a proheat upright, to install the suction diverter flap. Guy at the shop told me I had to do this but I don't think it was really necessary. Anyway, I am having a real job getting the cover back on. The shampoo mix piston seems to be causing the problem seating the two halves correctly. I see no obvious "right: way to put the piston back in. can anybody help me. Thanks Richard


Hey Richard. Turn the shampoo mix dial so the spiral is all the way at the top when you are looking at it from underneath. then, you want the piston to seat in the top groove of the knob. You want the piston's end that jets out to fit in the space ... Vacuums

Bissell proheat 1698 reassembly, smart mix piston, new pump?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a Bissell ProHeat 2x, and I did something dum. I had some powdered cleaner that said it works with carpet cleaners-well I mixed it in-and the next time I tried to use it, nothing came out. So, I took it part to check what was wrong-and found out that the powdered cleaner solidified in places. I cleared the nozzels, nothing. I think the solenoid, between the heater and nozzels is pluggd, and possibly the heater. I've got a question-could I use CLR to clean the heater, with replacing t


Heck yeah, give it a shot. Try running some water through it too- fill it up, heat it just to where it's hot and unplug it, shake it around and dump it out. Repeat. You might have to get a wire or something to go through and get the powder loosened b ... Bissell Vacuums

Replacing smart mix plunger bissell proheat model 7901 procedure for proper installation


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.B ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Replacing Smart Mix knob


The knob itself will only go in one way, What I was talking about is when you put the top cover back on, the knob should be in the water only position. This way the piston (on the bottom of the knob) will go into the slot correctly. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Smart mix what is the trick to connecting the smart mix?


Glad you did. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Connecting a BISSELL AUTO MIX PISTON TO A AUTO MIX KNOB


Take of the housing ,turn it over and you will see the under side of the auto mix dial , Then turn the auto mix dial to rinse only;\015\012On the top of the piston you will see a small slot , this fits into \015\012the out ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Smart mix plunger bissell 1699


This is what happened to me. The heater had to be cleaned. Easy fix. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Smart Mix Dial - Reassemble Cover


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell proheat pro tech model 7901-3 smart mix dial and valve assembly


Turn the knob to the water only, put the piston on the bottom of the knob then turn it slightly so it doesn't fall off, Start to put the cover on, when it is straight, turn the knob to the water only selection and push the top all the way down. The ... Vacuums

I have a bissell 1698 powersteamer. i have already cleaned heater and completely cleaned all parts , checked the mix piston, checked belt. it will not shoot water or mix. the motor runs, it will **** water and the brush turns. is it the pump and does the pump just shoot the soap?


Pump is probably bad. When you put the lid back down, did you put the piston on the bottom of the smart mix knob? Also the smart mix knob should be in the water only selection when the top is pushed all of the way down. Also sometimes the flow ind ... Vacuums

The solution in my smart mix will not mix with water and the button just keeps going round and clicks and will not stop on either water or solution.


The smart mix knob is connected to a piston that slides up and down into the automix assembly. This piston has come off of the smartmix knob and left the unit on water only setting. Sometimes the smart mix knob breaks on the ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Cleaner solution in smart mix tank not mixing with the water from the bladder. All tanks are seated properly


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I was mixing a cake mix on an old Kitchenaid Hobart Mixer Model 4 C for 5 Minutes and then white smoke started to come out. I don't think the mixer had been used in many years. Is this repairable or should I junk it. Thanks, Bonnie


... Vacuums

Smart Mix selector


I figured it out,since you nor Bissell was of no help. It turns out to be quite easy. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Smart mix valve reassebly and alignment


Have the piston on the screw threads, put the knob on the water only setting, then after the piston is on, turn slightly so it doesn't come off, just before you put the housing all of the way down, turn the knob back to the water only setting and the ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell powerforce vacuum brisals will not spin and i replaced the belt and it is still not wanting to spin and I think it will pop the new belt. what is wrong with it?


... Bissell 6594 PowerForce Bagless Upright Vacuum

Reset button The drive belt on my machine broke. They sent me a new one and I installed it, I think, correctly. It still won't engage and rotate the brushes. I can't find a reset button, but I suspect it needs to be reset. Where is the button? Theresa


Do the brush rolls turn ok? The brush roll motor may be bad.\015\012\015\012 ... Bissell 9400 ProHeat Upright Wet/Dry Vacuum

Changeing belt how do you install a new belt? I have an Eureka, The Boss, bagless, upright. The brush is hardly rotating. I think it could be the belt but i cannot open the vacumm to check it. How can I fix this?


... Vacuums

Have a bissell pro steam cleaner the suction is great but the water leaks out the bottom I think it should spray from the front and the soap cleaner won't dispense from the bottle so I have to mix the soap cleaner in with the water Any solutions


Use this guide!\015\012http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The smart mix bottle is not dispensing any fluid. I have been using this Bissell 8910 for 6 years. The cap and seal seem to have all the parts. thanks -LaRie-


... Bissell 8910 ProHeat Clear View Upright Vacuum

Central vac our central vac will not work unless the main vac in the garage is switched on manualy.... its sucking fine but i have to switch it off at the main switch in the garage after i have used it normaly i just plug in the hose and vac away and it switches itself off we have just had cable installed with a fisher guy in the walls do you think that would be the problem thanks a lot


It is possible that the low voltage wiring that controls your central vacuum has been damaged during the cable work. You can check to see if the low voltage relay is working by shorting the two terminals together at the unit. Just disconnect the two ... M&S Systems AirVac AVP1200 Platinum Series Central Vac - 12,000 sq ft Bagged Central System Vacuum

Belt type Ok, thank you for the help! I did have the top off, but did not know the taking the motor loose trick, thank you for that! Now I have a couple of more questions, and thank you so much for all of the help! I got a belt from sears, & the sales guy sold me an off brand belt. It looks just like the belt that broke, although do you have to force the motor back down into place? I think it may be the wrong belt? I have looked on the Hoover website & they do not even have parts listed fo


The belt number is 91001028. The belt will be snug but not real tight, so the belt you got may not be the right one. Most repair shops for vacuums should have this belt in stock. ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

I have a samsung SC7800 (smart wing system) vacuum cleaner. I think the impeller is jamed with sawdust. I have removed the part than holds the removable filter, but can't see how to remove the reat of the top case to access to impeller housing. Does anyone know how to do this or where I can view a repair manual for this model?


Unfortunately these tend to break frequently.... You might be able to get a wiring diagram at www.wize.com Good Luck!! ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0253 seconds