Having problems with your Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum ?

Red x does not turn water does not aooear to release properly


Answers :

Repaired many of these!

most likely its the pump.. the pump is located down by the brush...its belt driven(make sure your belt is there and in good condition)

the heater is located in the handle area...you could remove the hoses and blow through one end...shouldnt be restricted..


other possibilities

\015\012
    \015\012
  • bladder maybe empty
\015\012
    \015\012
  • formula bottle maybe empty
\015\012
    \015\012
  • tank may not be seated properly
\015\012
    \015\012
  • tank filter maybe clogged
Repair Help & Product Troubleshooting for Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Red x does not turn water does not aooear to release properly


Repaired many of these!most likely its the pump.. the pump is located down by the brush...its belt driven(make sure your belt is there and in good condition)the heater is located in the handle area...you could remove the hoses ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

I hav a floormate, it is just new and I can't get the water to release on the floor to wash it. I have the dial turned to wash and I do not get any water, the brushes do turn, but no water.


I had the same problem. I brought it into a repair facility and they took care of it. It appears that the trigger mechanism is a plastic shaft that warps over time, so what they did was to "extend" the shaft so when I pull the trigger, it actually pu ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Shark s3325 stopped working while steaming; thinking the unit had ran out of water I allowed unit to cool before refilling, however unit over flowed with only 700ml water added. When I plugged unit back into outlet it would not turn on (red light was not on) but I hear a click upon plugging in unit, when turning unit power button on and when turning on the handle switch. Please advise how to resolve this problem.


... Euro-Pro S3325 Handheld Steam Vacuum

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Bissell is not dispensing water or cleaner. The red piece that turns on top is not turning. I just started using it so the water container is not full.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My hoover carpet cleaner does not extract water. The brushes stopped turning since more than a month and now it doesn't extract any water. The engine is turning on but it does not work properly. I've checked for the solutions to this problem in the manual but any of the causes listed there apply to my machine. Thanks for your help.


... Hoover F5826-900 SteamVac Upright Wet Washer

We have the water hooked up at the back of machine. there is a spout for the water to come in and fill the ice tray.but is does not. If we turn the water on it fills up the space under the ice basket. I keep getting red light and then the two smal llight one ice and one water come on. We can hear the motor trying to fill the ice try and then lights come on. Please help me this so I can use this product. It did not come with a manual.


The water inlet valve on the back of unit opens when the ice maker needs water. If the valve doesn't seal good because of sediment or wear it will continue to drip and when the water reaches the ice maker supply tube it will freeze blocking the fill ... Vacuums

Hello i can turn my steam buddy platinum 44G258 on, water boils, press hand gun get a buzzing noise like you do with a jet wash, but no steam comes out, it seams the water is not coming through, have check the cap on water container thats ok, its where it releases the water to is seams to be where the problem is, i think ! first time we have tried to use it many thanks steve.


... Vacuums

My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.


... Dyson Vacuums

My HAAN Garment steamer was only intermittently releasing steam. I cleaned it out since there was some mineral deposits in there. After cleaning it out, I let it run for a while with distilled water and the same thing was happening. So, I called HAAN and they told me to troubleshoot. This entailed taking all the water out of the system and "shaking it out." Then to put new water in and turn it on. I was to do this three times and call them if it didn't work. After the third time, I realiz


... Vacuums

Bissell - Model 1697 - Powersteamer Pro - Carpet Cleaner I took the unit apart to replace some broken pieces and I can not seat the bottom to the top without properly engaging the soap/water mixer. What is the proper assembly procedure. What is the orientation of the water/soap mix valve when I seat the top to the bottom? The soap/water mix valve needs to engage the knob screw threads but this assembly is a blind operation. Do I turn to the soap/water mix knob to water only then seat the


Hi,\015\012http://dl.owneriq.net/7/7e477b7e-4440-49cf-a219-b68d301549e3.pdf\015\012This diagram will help you see the diagram plus the part assembly no and place it accordingly.I have also given link for Bissell - Model ... Vacuums

The unit sprays for the first few seconds after I turn the unit on and then stops spraying any water or solution. I turn it off, wait a few minutes and the same thing happens. What is going on and how can I get it to work properly?


This sounds as though the pump belt is slipping. This may be caused because the pump belt has stretched slightly or the pump is seized and will not turn. Remove the pump belt and turn the pump rotor with your fingers to see it turns freely. If ... Bissell 7901-R Clearview Proheat Plus Upright Vacuum

Red Ball I have a Hoover SteamVac Delux. The red ball pops up as soon as I turn the machine on, even though the tank is empty, so the machine will not **** any dirty water out of the carpet. Any suggestions?? ZThanks.


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

How to release and withdraw water solution to clean carpet.


Problem resolved by contacting a local retailer who provided instructions. ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My Bissell Pro-Heat 2x 12 amps Model 9200-2 The rollers wont turn and the water wont release


WON'T SPRAY ??? ... Bissell 9200 Upright Vacuum

I just recieved an old Rainbow D-3 vacuum (1980 's). Everything seems to be properly assembled but water spews from the basin when I turn it on. Suggestions?


Download manual here > http://www.rainvac.com/rainbow-vacuum-manuals ... Vacuums

Our SteamVac will not release cleaner and water. Everything else appears to be okay. After last use it was rinsed out and left for two weeks at which time it would not work. I would like to obtain a repair manual to study and be able to disassemble it properly. Thanks in advance, William Ferguson E-mail: [email protected]


Click this link directly\015\012http://www.sacreativeservices.com/forum_stuff/steam_vac/\015\012\015\012 ... Vacuums

Bissell proheat will not dispense water red idicator does not turn


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.B ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell 1698-1 Solution applicator indicator (red spinner) does not rotate and no solution is being applied even though both the water and cleaning sol'n tanks are full and properly nested.


The heater is blocked wih lime scale ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

When you turn on the machine the light goes green,I then switch the lever over on the top to red for a hot drink,the machine makes the noise and you think its going to make your drink but no water comes out,My son brought it for xmas last year and didn't think to keep the reciept. thanks lisa


Turn off ... Vacuums

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet


Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums

During the winter i turn the dehumidifier off. but when i turned it back onthis spring because you can feel the dampness in basement, it turns on but it does not absorb any water. i cleaned filter??? it turns on and sounds normal but it isn't taking any water in??? help


Turn the machine on maximum and let it run for an hour or so. Then check the coils in the back with your hand. If they are not getting cold at all, then there is a significant problem with the refrigeration process in the unit. It may have developed ... Vacuums

I got a used bissel 1720-9 bissel cleaner..It holds water,,and turns on but no water comes out the nozzel?? what side of tank do i put the water in also there was no instructions,,there is suction when i turn it on but no water,,


You can download a user guide from www.bissell.com Just type your model number in the search panel ... Bissell 1720-1 Little Green Wet/Dry Vacuum

We have a Bissell Proheat 2X (model 8920). The problem we are having is when water/soap is initially released (all settings) it continues to leak out the front water spray nozzles unit the water containers are empty. The vacuum works but can't keep up with the continuous water leaking out. Do you have any idea what is sticking open to allow the continued release of water when the machine is running? Thanks Rick


Return it. It is faulty and should not do that. Mine does not. Does require changing water about evrery 10 minutes but one can see the filth in the water. Also re-clean with plain water over areas that were cleaned to remove all cleaner. Old cleaner ... Bissell 8920 ProHeat 2XTM Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0884 seconds