Having problems with your Bissell 1699 ProHeat Clear View Upright Steam Vacuum ?

Handle trigger not releasing cleaner and solvent to brush head

\015 Upholstery hose is working\015

Answers :

Repair Help & Product Troubleshooting for Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Handle trigger not releasing cleaner and solvent to brush head

Try this guide.\015\012http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a Bissell Proheat 2x cleaner which has worked perfectly on every occasion. Today I filled the machine as usual with water and formula and switched on, the motor ran, the lights were on and the brushes rotated but upon pressing the spray trigger no water or formula was released. I have cleaned the jets underneath and also followed instructions to release any airlock. It still wont release the water/formula. What else can I do? Thanks Charles

Please check the following with liquid in both tanks.\015\012 \015\012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\015\012- ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Cleaning I cannot get the cleaner to release solution on carpet. have lost manual. is there a trick to this? I have tried squeezing trigger handle to dispense solution with no luck. have followed instructions (2 capfuls cleaner, fill with hot water to fill line) on filling tank.

Either you have a pinched or clogged water line, or the rod in the handle is pushing down like it should. The drw back is Bissell has deemed this unit and its parts obsolete. So any parts are hard to find.\015\012\015\012 ... Bissell 1950-3 Quicksteamer Plus Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Beater brush will not spin and head drops down without using foot release

You didn't provide the model number so couldn't look it uo, but sOme of the progressive uprights have a circuit breaker on, it will trip when something catches on the brush roll, push it to see if it will reset, if there isn't one, get me the model, ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

I have a Kenmore vacuum cleaner model #116.34720. The problem I am having is that if you are rolling the vacuum around, the base will drop without pressing on the handle release pedal. This often results in a bunch of dirt being dumped back out. The manual doesn't show anything about adjusting the handle release pedal so it holds the handle and base in an upright position better. Any help is greatly appreciated! Thanks in advance!

... Vacuums

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?

The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a

Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

The wand release button has broken. Therefore, the wand does not lock into place which results in swivelling of the handle and sometimes the handle coming off while using the vacuum cleaner. Can this wand release be readily repaired?

... Euro-Pro NV31 Infinity Vacuum

How do I remove the cleaner head of my Dyson 24 upright. it has no release button like one that was featured in a how to video. ??

Some of the heads have a push button and some have u type clip you need to remove with screwdriver to flick it off ,this video on the link below will show youhttp://www.youtube.c ... Dyson Dc24 Cleaner Head Assembly

When squeezing trigger and Depressing Clean surge Button on Upper handle of the Hooover Steam Cleaner F5914-900 there is no "snap" indicating trigger rod is in place. Everything else went in as instructed. The screws and bolts were no problem this concerns me because the main complaint I read about this model was leaking from the trigger and clean surge and the problem was not getting the rod in place. No matter how many tries or people (three) it still doesn't occur.

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=552215\015\012Generic problem for all Vacuums\015\012When squeezing trigger and Depressing\015\012P ... Vacuums

Model 79011 ProHeat - First the water and cleaning solution wouldn't come out without pressing the trigger several times. Now the trigger doesIs there a spring on it inside the handle or do I just need to order new trigger. I have only used the cleaner 3 times.

... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Dyson DC25 - Cleaner Head Brush pin broke

... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Can't release brush head on dyson dc24

Hi there,I'm sorry to hear you're having difficulties with your DC24. The red button you're referring to is the brushbar motor reset button; the catch to release the brushbar is on the underside of the cleaner head.To clean any thread ... Dyson Ball DC24 Bagless Upright Vacuum

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!

Great. ... Kenmore Vacuums

Steamvac will not stop dispensing cleaner. Once I pull the trigger it starts to dispence liquid and will not stop even when I release the trigger.

This sounds like a faulty solenoid that may be intermittantly working. I would take it to a repair shop for evalualtion ... Hoover F7431-900 SteamVac Vacuum

Brush heads don't spin - Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Your belt is broken. Remove the sole plate to access. Parts available at FixYa.com advertiser, your apliance parts or auto parts place or www.repairclinic.com ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Chassis hook broken to rod which controls release of liquid shampoo in Hoover steam cleaner. It is the back of the handle area that is snapped off, not the actual rod with "push on / release"

If it is part of the handle, it breaks inside alot, part number 39458006. #2 in the picture.\015\012 \015\012 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Bissell Powerease Lighweight Deep Cleaner. (Shampooer) After I fill the solution tank with the solution and water, I put it in it's slot, but all of the contents just come flowing out. I have only used this machine twice and it worked ok. You are supposed to press the trigger and the solution sprays out and then release the trigger when you want it to stop. But like I said, now I just put the tank on and all the contents come flowing out. I don't know what's wrong or how to stop it.

... Vacuums

When using the floor configuration, I can't get the trigger to cause a spray of either water or cleaner. When using the tool configuration and the hand device with brushes etc, the spray works well with the hand trigger.

The trigger on the handle for tthe floor configuration has become loose or broken. When you squeeze it, the action pulls a rod that runs down the length of the shaft and goes into the base and allows the water to spray. You need to check and make sur ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Electrolux Z61 Handheld Vacuum Cleaner. Brush heads have stopped turning. Have removed screws but the casing seems to be still fixed together by a plastic joint which looks as if it will break if forced. How can I check that the belt is OK, and if it isn't, how do I open the cleaner to replace it?

... Electrolux EUK71B Bagless Handheld Vacuum

I have an Ambassador canister model Electrolux. The powerhead shut off and the brush doesn't turn. There is nothing wrapped around the brush and the connection from the handle to the power head is fine. Any suggestions? Thanks AG

CHECK TUBE-SUMO ACTIVE ( PART NO: 1131402-02 ) CONNECTION AND NOZZLE-SUMO ACTIVE OR REPLACED (PART NO: 1131400-02) ... Electrolux Lux 7000 Bagged Canister Vacuum

My Shark is less then one year old. The Shark steamer will heat up - the water is hot - however, when I push the handle to mop the steam is not released, then it cools down and only cold water is releases from the mop head.

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Cleaner Head flopping down

Hi.\015\012\015\012This is very common problem & easily put right just go to Dyson UK site They have a help section with pictures that will show you how to fix this.\015\012\015\012\015\012Chris.. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Just got a bissell proheat clearview force cleaner, we press the trigger, no water sucking action or shampoo release going on .. what's wrong?

By the Floor Cleaning setting knob and Tools for PreHeat setting knob, there's a red x inside a clear circle cap. Is it spinning at all? If not...twist the cap off and remove the red x. Under the red x there is a tiny little filter. This might be plu ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0947 seconds