Having problems with your Bissell 1699 ProHeat Clear View Upright Steam Vacuum ?

Bissell proheat turbo 2x upright cleaner -how do I reassmeble?

\015 I have dismantled my Biseell Vacuum Cleaner to clean it and now can't put it back together. Can you please give me a step by step guide on how I put the rollers etc back together.\015\012Thanks\015

Answers :


\015\012Yeah, it’s annoying that the manual doesn’t give more detailed instructions and drawings to help with this, because you do have to take the roller assembly apart sometimes to clean built-up carpet lint off the unit properly. If you don’t do this, I’d expect you’d have more problems.
\015\012
\015\012I have a different model number Bissell Proheat than yours. Yours may have different parts or go together differently than mine, but I'll tell you how I do it on mine and you can try my way out and see if it helps you.
\015\012
\015\012(In all cases where I use left vs. right or front vs. back, as when these terms are used with a car, I am facing the front of the Bissell. I am NOT behind the Bissell, where I would stand when cleaning carpet with it.)
\015\012
\015\012
\015\012Here's how I put it together. This takes much longer to describe than to do, once you figure out where everything goes and you get the hang of doing it!
\015\012
\015\012Attach the left arm with the two silver rods (ONLY attach the left arm here-- leave the corresponding right arm, which looks like the left arm except it has no silver rods, off the bottom unit of the Bissell, for now) to the left side of the Bissell, with a silver screw with a built-in washer. The screw hole is on the back end of the arm and the arm dips down towards the front of the Bissell and holds the two brushes in position so that they can turn without striking the top of the underside of the Bissell or dragging on the floor.
\015\012
\015\012Put a small silver washer on each long, silver metal post, where the roller brushes will go, and slide it all the way to the left.
\015\012
\015\012Put the larger rubber belt around both metal posts, about halfway to two-thirds of the way down the metal posts.
\015\012
\015\012Slide the brushes halfway down the metal posts and attach the larger rubber belt to the cog wheel on the left side of each roller brush. Then slide both roller brushes with the large rubber belt attached all the way to the left so that the cog wheels are against the inside of the left arm. As you move the roller brushes almost all the way to the left, you may be blocked from reaching the end until you carefully work the rubber belt around a plastic flange on the inside of the left arm, but do this and be sure the roller brushes are up against the inside of the left arm. Make sure the rubber belt is still on each of the cog wheels when the roller brushes are pushed all the way left. If you turn one roller brush, the other should turn, too, because of the belt attached to both cog wheels.
\015\012
\015\012Put the small belt around the small cog wheel on the bottom unit of the Bissell behind the right end of the back roller brush, and also around the cog wheel on the right end of the back roller brush. (The right cog wheel on the front roller brush is the only one of five cog wheels without a belt, when everything is assembled correctly.)
\015\012
\015\012Put a small silver washer on the right end of the silver rod passing through the back roller brush.
\015\012
\015\012NOW attach the right arm, using a silver screw with a washer, to the middle screw hole on the right side of the bottom unit of the Bissell. The right arm should mirror the left arm, so that the two arms hold both roller brushes in position on the right side and straight across the bottom unit of the Bissell. It is normal for the roller brushes and arms to be able to flex up and down a bit, when everything is put together correctly. The built-in washers on the silver screws which attach the arms keep the arms and roller brushes in the generally correct position but allow them to flex.
\015\012
\015\012Now using your fingers you should be able to slowly spin the roller brushes without the brushes contacting the top of the bottom unit of the Bissell and without dragging too low against the floor. Check one more time and be sure the belts are positioned correctly around four of the five cog wheels.
\015\012
\015\012If everything seems right, attach the two side covers. These are not interchangeable; the left cover only fits on the left. The short black screw goes in the back screw hole, and the long black screw goes in front.
\015\012
\015\012Then attach the front cover. It's important to be careful that the hooks on the front cover are inside the side cover holes designed to hold the hooks before trying to tighten the last screw through the tab on top of the front cover. If you aren't careful about this, it's easy for the front cover to be out of position or to break its tab.
\015\012
\015\012Try powering up the Bissell and see if the rollers spin correctly. Remember that the handle must not be locked upright and the trigger must be depressed with the Bissell turned on before the roller brushes will spin. (Sometimes people complain that nothing happens with the unit turned on and the trigger depressed when the only problem is that the handle is in the locked upright position.)
\015\012
\015\012Good luck!
\015\012
The hoses go? My husband took it apart and is now not sure.
Repair Help & Product Troubleshooting for Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissell proheat turbo 2x upright cleaner -how do I reassmeble?


\015\012Yeah, it’s annoying that the manual doesn’t give more detailed instructions and drawings to help with this, because you do have to take the roller assembly apart sometimes to clean built-up carpet l ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Instruction manual for bissell proheat turbo - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Airlock in my carpet cleaner bissell proheat - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Bissell proheat 2x 8930 won't spray - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Bissell proheat no water - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Bissell proheat 2x not dispensing soap - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Proheat turbo 2x operating instructions - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

The bissell proheat will not suction - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


Try the following suggestions to see if you can get your machine suctioning properly:\015\012\015\0121) Remove the Tank-in-Tank Assembly and place your hand over the motor intake valve. This valve is located next to the Floor Nozzle gaske ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Bissell carpet cleaner not dispensing water - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Bissell proheat isn't spraying water out - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


Hi,As the weather is getting warmer for many people their freezer and/or refrigerator do not work right because of a dirty condenser coil...there are also many other things that can go wrong. If you are hearing a clicking or buzzing ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

ProHeat Turbo Deep Cleaner Upright Steam Vacuum: Hello, My Bissell Proheat is not spraying water, ...


Most likely the pump belt is worn and needs to be replaced. Here is the belt you need: Bissell Proheat Pump Belt ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Cleaner solution doesn't mix with the water - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


Hi, this is very common problem the problem is that the problem is a simple one but solving it can take time. The problem you have got is that the detergent has turned to a gel over time and caused a blockage somewhere in the system now the problem y ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My bissell wont spray water or suck up water - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Manual for a bissal proheat 7700-f - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My bissell 2x has little to no suction - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


Here's a quick link to tips to help take care of your issue:\015\012http://www.bissell.com/FAQDetail.aspx?id=1124&cid=ccsocial ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

How disassemble bissell 8920-3 - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Water wont come out fo the steam cleaner. - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


Try adding a table spoon of salt to the water. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My bissell steamer smell burning - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Changing trigger in the bissell - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


Hi Scott. You may want to purchase a new handle for your BISSELL machine. Here's a link to the BISSELL website. \015\012http://www.bissell.com/parts/?cid=ccsocial ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Brush will not spin on the steam cleaner - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My bissell wont spray - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


Depending on which bissell you have; I would check the heater. If it is a newer module I would check the solenoid switch. The heater heats the soap up so much that it clumps the soap up and clogs both of these parts. I would also check the tips thems ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My bissell will not **** up water - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Water doesn't come out - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


Hi this is very common problem what you need to do is lie the vac on its side then where the water comes out of the little jets at the bottom of the vac these are usually blocked and will need cleaning using a pin to poke through should solve the pro ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Where do I put in water? - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


If you have to ask this question, then you are too stupid to be using this equipment. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

How do I change the Brush Belt? - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


It depends on the type of ProHeat cleaner you have. But you can go to www.bissell.com and download the manual for your model and you can get the belt you need at ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1061 seconds