Having problems with your Bissell 1699 ProHeat Clear View Upright Steam Vacuum ?

Splitting the case

\015 How do we get the case open to check if the heater is clogged. we have been trying and it does not just pop off. seems like it will be easy to break.\015

Answers :

The heater is in the handle. Take out the 2 long screws and nuts, remove the handle. Then on the back, below the cord and hose warp, there are 2 more screws, then lay the handle down, you will see s catch. push it in and the handle pieces will come apart. Pull the 2 lines off of the heater,( remember which ones goes where)Use a nail or something small that you can push in the ports that the lines were hooked to and clean them out, try to blow thru to see if if is cleared out. Then re-asemble.
Repair Help & Product Troubleshooting for Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Split case on Bissell Proheat to clean hair out of

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9400 ProHeat Upright Wet/Dry Vacuum

How do you split the bottom case for the uv3?

... Pullman Holt Uv5 Bagged Upright Vacuum

Splitting the case

The heater is in the handle. Take out the 2 long screws and nuts, remove the handle. Then on the back, below the cord and hose warp, there are 2 more screws, then lay the handle down, you will see s catch. push it in and the handle pieces will come ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Need to split case of excellent solutions ltd model c 2006 g vacuum cleaner

... Vacuums

Hoover Alpina 2 1300 cleaner. I need to split the upper and lower casings to check that the switch is working. I have removed the screwa in the area around the bag, but now need to remove the switch and cable rewind covers, as I assume there are more securing screws under them. Can you advise how to do it please?

Move covers (forcibly !) away from the centreline of cleaner then move to rear until released. The covers are held by slide catches on inner edges. ... Vacuums

I need to repair the cord reel on a Electrolux Lux7000, Model C153A. How do you split the case?

If that is the electrolux thats the plastic housing, the side bumpers pull forward towards the bag door. when the two bumpers are removed, the case will separate. Be gentle though because the plastic is usually very brittle and could possibly snap pr ... Vacuums

Jun 24, 2010 - Jun 24, 2010 - Needle not bent/ new needle not answer. I finally conclude that the entire bobbin case is ROTATING in its seat, which jams the needle. The "projection" is against the "spring" when I install it, but I can rotate the bobbin case PAST the spring without trying very hard. Bobbin case MIGHT get held in place better if it were closer to me (front of machine). I feel it is still not out from under needle plate as shown in diagram, but can't keep it closer to f

Hi,Your problem dated 24th June 2010 was re-posted today. If it has been already resolved, kindly ignore this message.Thanks for using FixYa ... Vacuums

Dyson DC 14 hose has no suction, with or without brush attachments. Hot air shoots out from the base of the canister when I try to use the hose. I cleaned the top filter, but can't figure out how to remove the hepa filter to clean it without destroying the case. It looks like it might take three hands to insert pennies and "flip" the case open as is suggested on a youtube video for a different model. Would this even help, assuming I could get the thing open?

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My vacuum hose has split very close to the handle- how do I remove the handle, cut the hose at the split & reattach it to the handle unit - Centralux central vacuum system. Where can I find a diagram of how to remove the handle?

Do Not Cut the hose! It has wiring inside to control the vac and power head. This is a swivel handled hose with both low and high voltage contacts in it. The same wiring which gives the hose its ribbing, is conducting current for two applic ... Electrolux Centralux Vacuum


From the Argos website... they must repair or replace or refund, up to 1 year. The squeaky wheel gets the grease, go over her head.\015\012 \015\012If there's a fault with the product...\015\012We've made it easier!\015\012 ... Vacuums

This is not an electrolux problem, but I am hoping one of the experts can answer the question. I have a Sears air compressor that suddenly stopped working. After looking at how the motor case is put together, it appeared that it would essentially have to be destroyed to get it apart and into the motor. I received a new compressor for my birthday so I decided to tear into the old one to do some diagnosis. After getting into the case where I could see the motor/pump, I have discovered the prob

This is intersesting. I think the fuse is simply a heat sensor. If you by pass this the only problem you may run into is if the motor over heats it my eventually burn out. However, for what you are using it for overheatin should not be an issue. This ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Split hose? My machine has stopped suction on the main unit. When I tilt the neck all the way back, the hose is split around its diameter. Is there a straightforward way to fix this AND where can I order th part?

This piece is available but is very difficult to install. the upper handle needs to be split to reach the upper part of this hose. i would call the manufactuer and find a local warranty service center to get this part. ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

Polti 2400 I am trying to remove the casing from the steam cleaner to fit a replacement wheel. The screws holding the casing are similar to torx but they have a raised centre which means they can't accommodate a torx screwdriver. I thought this was going to be easy just replacing a snap-in wheel!

You can buy T15 torx driver with hole in them from link below. ... Polti Vacuums

Remove casing Remove outer cyclone casing

You can remove it by watching instructions at youtube. ... Vacuums

Air lock in case case ih ps160 sprayer

... Vacuums

I have a Samsung 4320 vacuum cleaner which has started making a loud blowing noise as if the hose is split. I can't find a split in the hose and it isn't blocked. Also it isn't picking up very well. Can you help?

Most vacuums have an air duct on the hose to adjust the amount of suction. If this becomes opened, you will hear the sound you've described and the suction will lessen. Check the wand and the hose and see if you notice a sliding piece that can be mov ... Samsung Easy 1300 Lightweight Compact Canister Vacuum Cleaner

So, I was sewing along and heard a thump...kind of sounded like a louder version of what you hear when the needle hits a pin...but I wasn't using pins. This, of course, lead to the thread jamming so I had to clear that. When rethreading I pulled out the bobbin case to make sure it was seated correctly and found a kind of "v" shaped piece of wire (about the width of a paper clip I guess) sitting loose under the bobbin case. I took it out and threw it away. Still can't pull up the bobbin threa

That part was the hook end of the spring that was supposed to put tension on the bobbin - it will have to be replaced. This is a special flat spring that unfortunately only a repair shop of a dealer has it - you will have to take your machine to one. ... Vacuums

I have singer fashion maker 2818. The problem is the bobin casing (the one which holds the bobin)is coming out (i.e) loose. trying to fix it in place but not sucessful. can someone explain how to open and fix the case and place the other supporting covering so that there is smooth motion of the needle and the bobin.

... Singer Vacuums

How to open main case on a dc08. i have removed the two screws under the top filter but i can not figure out how to seperate the main case so i can replace main switch. any help would be much appreciated

... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

How do I install the bobbin case and bobbin case body in a model #9420 singer sewing machine

... Singer Instruction Manual - 9420

I took out the bobbin case & not sure if I put it back correctly. Now I had my thread going under it instead of over it.

Download the manual here > http://www.singerco.com/accessories/instruction-manuals ... SewShop.com Singer Model 4562 Instruction Manual

The power cord is split near the base unit

There are 2 screws on each side of the top cover of the Rainbow ‘E’ series vacuum cleaners located behind the decal windows. To get to the screws; use a non-scratching tool such as a plastic putty knife and pry out a corner of the plastic ... Rainbow E series Canister Wet/Dry Vacuum

I am trying to open the outer casing of the vacuum

There is a push in type flat plastic switch trim cover over the metal housing surrounding the switch.. You must unplug the cord, gently pry around the trim cover and you will find a screw, an irregular one underneath holding the switch in place. DO ... Vacuums

There is a cut at the end of the hose. Is there a way to cut the hose at the split and reattach it to the connection? Thanks.

Unfortunatly the amswer is no you will have to replace the whole part. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Maytag F6212-901 suction hose split

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0137 seconds