Having problems with your Bissell 1699 ProHeat Clear View Upright Steam Vacuum ?

I have a bissell proheat turbo2x the brushes wont rotate checked for blockages none to be found can anyone help


Answers :

The belts are probably broken, stretched or worn. I would try replacing the belts if you haven't in a while. You can get the belts you need here:

Bissell 1699 Replacement Belts
Repair Help & Product Troubleshooting for Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a bissell proheat turbo2x the brushes wont rotate checked for blockages none to be found can anyone help


The belts are probably broken, stretched or worn. I would try replacing the belts if you haven't in a while. You can get the belts you need here: ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Nothing spraying out of Bissell Powersteamer Proheat. I've check filter under flow indicator, pump belt is fine, cleaner in proper tank, bladder of water tank is full. We've had it for a very long time but it's barely been used. Can anyone help?


... Bissell 1698-1 PowerSteamer ProHeat Plus Upright Vacuum

I have a Bissell ProHeat 2X which releases the water/shampoo mix fine, and will suck up using the hose, but will not suck up using the main floor unit. Have checked it all out, and there do not appear to be any blockages. Help please


The vacuum on its back then look under the front where the water comes\015\012out, you will see few little round holes now the chances are these\015\012holes are blocked so get something long like a pin and poke these holes\015\012through you should ... Vacuums

My Bissell 3920 motor is making a high pitched noise. I have cleared out pet hair from top to bottom. Cleaned the lower filter and replaced the upper filter. I Checked for blockage in the hoses and found none. The filter indicator goes green when I turn it on, but the straining motor noise persists.


Click on the link below to view the replacement motor and fan for your Bissell 3920 vacuum\015\012\015\012http://www.vacuums24x7.com/motorfan.html ... Bissell 3920 Bagless Upright Vacuum

Hello, could you help please. I have a Bissel ProHeat 9400-M. The water remains in the bladder when the machine is on, in other words nothing happens and I cannot clean with it. Inside the tank the small flap is in the open position. I have always used your products although I did run the Bissell over an area that had been cleaned with another product. Could that have caused the problem by blocking it somewhere? I have cleaned everything and cannot see a blockage. Thank you for your help.


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Suction stopped. Roller and belt working-in fine order. Checked hoses have not found any blockage. Blowing out air or sucking so little can't feel it with hand on hose end. Help!


Either a blockage or the main air filter is blocked , some it can be washed and others it must be replaced I would check the owner manual and look at the filter, foam ones can and usually have instructions where they install to wash them. ... Hoover Tempo Widepath Upright Vacuum - Blue

My power head to my rainbow does not pick up as well as it always has. I've checked for blockages - none found. Checked the belt on the bar and replaced it just in case...any suggestions?


Clean or replace the separator under the main motor. Brushroll may be worn and needs to be replaced. Make sure the bottom plate is on correctly by catching the tabs on the front of the head and then fastening. ... Vacuums

There is no suction from the sweeper head but plenty from the wand. I have viewed several videos and visited seveal dyson web pages and none address this problem. I have thoroughly checked for blockage per video instructions. There were NO BLOCKAGES. Please help. Thanks Doug


Hi Doug,\015\012\015\012There are several things that this could be. Probably the most common problem that we see when customers come in with this problem is actually a fairly simple problem to fix. Here are just a few things that this co ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I HAVE A BISSELL PROHEAT 2X HEALTY HOME, IT WORKED JUST FINE THE LAST TIME I PUT IT UP. YESTERDAY, I NOTICED THE FLOW GAUGE WAS NOT SPINNING, SO I CHECKED AND SURE ENOUGH NO WATER WAS COME OUT. I CHECKED AND ALL THE TUBS AND EVERYTHING ARE IN THE RIGHT PLACE AND HAVE LIQUID IN THEM. HAVE TRIED PRIMING CLEANING THE BRUSHES RUNNING HOT WATER THROUGH IT... HELP


Have you made sure that the tanks are seated properly and the red \012(or black) auto-load gaskets are in place. \012Check the bottom of the Water Tank and the Formula Bottle to make \012sure each has a red auto-load gasket attache ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?


... Bissell 8910 ProHeat Clear View Upright Vacuum

I have an electrolux Z8280 cyclonic twin clean vacuum cleaner 2000w. At the moment the power (blue) and filter light (red) are both flashing at the same time and it won't turn on at all. I have emptied the dirt, checked for blockages, and checked the filters and i still don't know what the problem is :( Can anyone help me? Thanks


It's REALLY easy: https://www.youtube.com/watch?v=HiHwY-lncc0 ... Vacuums

Replaced the pump and solenoid on my Bissell Proheat, model 9200 H, but not sure I got the tubing connected back right. Can anyone help me with this?


... Bissell 9200 Upright Vacuum

I have a Bissell ProHeat 2x, and I did something dum. I had some powdered cleaner that said it works with carpet cleaners-well I mixed it in-and the next time I tried to use it, nothing came out. So, I took it part to check what was wrong-and found out that the powdered cleaner solidified in places. I cleared the nozzels, nothing. I think the solenoid, between the heater and nozzels is pluggd, and possibly the heater. I've got a question-could I use CLR to clean the heater, with replacing t


Heck yeah, give it a shot. Try running some water through it too- fill it up, heat it just to where it's hot and unplug it, shake it around and dump it out. Repeat. You might have to get a wire or something to go through and get the powder loosened b ... Bissell Vacuums

I have a Bissell ProHeat 2X Carpet Cleaner. Problem is, it's not vaccumming up the water it puts down. I've checked filters to see if anything is clogged. Can you help me?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell proheat clearview 12 amp 5 cleaning rows of dirtlifter powerbrush. It won't shoot the cleaner to the brushes. I cleaned the filter, checked the belt, water is full, and soap dispenser is full. Still no soap going to rug. Can you help? Thanks


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

I've changed the belt on my Bissell 3760-2 model but the brush still doesn't rotate. I've checked for clogs and there are none.


Clogs affect the air movement, but not the brush assembly. Remove the brush assembly from the vacuum base. Remove, clean, and lightly oil (with 3-1 or similar) the two end bearings. They are usually choked with debris to the point that they lock the ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

My Dyson DC07 stops working after a few minutes. It works again after a further 10 minutes and then cuts out again. I have cleaned the filter and checked for blockages but is still cutting out. Can anyone help?


Have you tried calling Dyson? I had a problem with my Animal, and their tech department talked me though the fix. Worth trying them first. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a used Bissell proheat pet machine with no users manual. It will not extract water. In fact it blows air out instead of vacuuming. I checked the belt it is fine. All hoses looked good too. It has no vacuuming with the attachments either. Help. Betzi


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My bissell proheat is leaking a lot of water! What is the problem. I dont know what to check can you help?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a Bissell Upright Proheat 2x and the dual power brushes wont rotate. I went to replace the drive belt and noticed the drive shaft does not turn when power is turned on. What shall I check next?


Is there a light that comes on when you "turn the power on." If there is no light, and the unit is plugged in, how do you know there is current going to the motor? Sounds like there might be a break in the cord. Examine the cord near the plug end ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl


There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap ... Hoover Vacuums

No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema


Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a cannister (Animal something...) Today, it didn't sound right - like a blockage. I took out the filter - seemed OK; I looked for a blockage - found none. I continued to vacuum, but it wasn't picking up. Then, I stopped again, and I found a blockage (cat toy mouse) right at the end of the hose (attachment end.) I cleared, and I turned back on - nothing. Completely dead. It is one year old, just about exactly. Desperate, Sharon Tracy


Hello,if your canister is completely dead, then it means its having a power problem. You need to focus your attention on that part of your canister that relates to power. Such as; power wire, if you don see any fault with the power cord, ... Dyson Vacuums

Bissell Proheat x2 = No Floor water output or Brushes rotating


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Dyson all floor vaccum no suction when hand held wand is turned on... doubled checked for cracks in hose -- none took house off unit to check for blockage --- none.. suction works fine when using as normal on floors.


You need to replace the belt that drives the brush on the underneath side of the vacuum. To do this, you need to flip the vacuum over and remove cover plate. There you will find the broken, or stretched out belt. Remove the brush and place the new be ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0682 seconds