Having problems with your Bissell 1699 ProHeat Clear View Upright Steam Vacuum ?

When I push the button to release the water to start the steam process, nothing happens


Answers :

You will need to remove the heater coil that is located in the handle, remove and mark allthe hoses and wires then remove the screws from the plate on the coil, make sure to not lose the red seals you will see alot of calcium build up use a brush to clean the maze that is inside and use a toothpick to make sure that all of the inlet and outlet holes for the hoses are clear put it all back together and you should have fixed your problem let me know thanks Don
Repair Help & Product Troubleshooting for Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When I push the button to release the water to start the steam process, nothing happens


You will need to remove the heater coil that is located in the handle, remove and mark allthe hoses and wires then remove the screws from the plate on the coil, make sure to not lose the red seals you will see alot of calcium build up use a brush to ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

While using my mop yesterday, it stopped letting steam come out. Tonight I plugged it up again and you could hear it trying to steam. I push the button in to release the square frame and it pushed out a burst of steam and pushed the head off. Put it back together and it still will not let steam out. No matter how much water is in it.


\012Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Ste ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have the Oreck Sanapathic DMS2000 Handheld Steam Vacuum, but no steam comes out when I push the button. I hear the motor, is there any buttons I am missing or any help on how to make it work, been plugged in for 5 min now. Held button down for 2... nothing. Just a drip of water.


ORECK DMS2000 No Steam First, tested tank and filter flow together using suction via plastic tubing. Worked freely Second, removed pump and disconnected hoses and terminals [watch location,three terminals on pump, two plugs] ... Oreck Sanapathic DMS2000 Handheld Steam Vacuum

I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh't start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat


It was overheated that is why it worked downstairs after cooling off. ... Miele S548 Bagged Canister Vacuum

Hi, I've a Tefal Steam Generator Express Turbo 2910. It won't "steam". The solenoid works when the button is pressed. The pump works. I've cleaned the tank (with white vinegar as recommended on this site!) thoroughly. The water from the steam tank is only "hot" (not scalding as I'd expect it to be). When first switched on and hot enough there is the TINIEST whiff of steam when the button is pressed then nothing more. Do you think this could be the Thermostat Part CS00094126, or can you


... Vacuums

Producing steam i just got the shark assembled the mv2010, then it is not doing anything, it vacuumed just fine, but when i put the steam pad on it wouldnt ever produce steam or do anything,it felt like the water was heating up but even after it sat for 20-30 minutes when i pull handle back towards me nothing happens, no lights no steam no nothing, so why wont it work


This link is for the manualhttp://www.sharkclean.com/manual/MV2010_11_IB_ENG_110103.pdf ... Shark MV2010 Vac-Then-Steam 2-in-1 Vacuum and Steam Mop Purple

Water will not come out when i push on trigger button. So water does not come out. I have taken it apart and cleaned it. The problem seems to be in the triggerI push on the handle to release the water.


Order the part from bissel see if that fixes sound like you know what wrong just need get part number from bissell.Could be some kinda pump also thats bad not pushing out the water.I got bissle heated one black it only problem the seals r ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I bought a used Miele vacuum with the SET210 wand, but the push button to release and clamp the telescoping wand was missing. I can get the wand to slide by pushing with my finger, but it's a little difficult. The main problem is that nothing holds it in place at the desired position. I bought a replacement push button online, but it came with no instructions. How do I install it?


Your best bet would be to put on your friendly face, and take the unit into a Vacuum Repair Shop, and have them assist you, or at least give you tips on the procedure. Chances are you will have to disassemble the unit a lot more than you might want ... Vacuums

REMOTE CONTROL IS MALFUNCTIONING & NOT TURNING ON CUSHION - Hello. I bought a used (by near new) Shiatsu+ Massaging Cushion from Ebay. When I installed it today the remote control was faulty. When you push the Power button, the blue light comes on, but none of the other buttons work. When you push the Power button again to turn it off, it clicks & turns itself back on again. So it's running but nothing is happening in the massage cushion. I did see a card in the box saying "For the Shiatsu


Before you use this cushion you MUST first 'unlock' the rollers which are held in place by a screw which MUST be removed or the unit will self destruct. The manufacturer provides a hex wrench to remove the shipping screw and a large label on th ... Vacuums

While using, steam stopped coming out in force at the port levels in the head. Suddenly started high pitch whining, pressed button just above connection site and end flew off with great force pouring water onto floor and carpet. Unplugged immediately for safety and unable to get it to deliver steam force again. Less than one year old and used only 8-10 times only in walk areas where there is no carpet with distilled water. Please, advise, cannot find booklet. Thanks So Much, Beverly Crumme


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it may not be getting steam to the head...Euro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

My Shark is less then one year old. The Shark steamer will heat up - the water is hot - however, when I push the handle to mop the steam is not released, then it cools down and only cold water is releases from the mop head.


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

When I push the button to release steam on the handle it feels soft and no steam is released. It has been going out for a while now.


I didn't fix the problem but I did take the handle apart. There is a little metal piston that is pushed down by the button on the outside of the handle. It was very sticky and stuck in the off mode. I freed it when I took it apart but obviously it ju ... Steam Fast SF-275 Steam Max Canister Vacuum

My shark steamer has stopped working after a year of having it (I have already replaced one, I'm a idiot!). My problem; however, is that it will steam, but the steam stops traveling through the actual "mop" part. I plugged it in, wait seconds and start pumping, but the steam builds up until it's hard to pump. I had to press the button really hard for the bottom to come off and it shot off like a rocket! I tried to stick something through the tubing, but it did nothing. What am I doing wrong? I


\012\012\012Hi,Here\012is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it\012may not be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

My HAAN Garment steamer was only intermittently releasing steam. I cleaned it out since there was some mineral deposits in there. After cleaning it out, I let it run for a while with distilled water and the same thing was happening. So, I called HAAN and they told me to troubleshoot. This entailed taking all the water out of the system and "shaking it out." Then to put new water in and turn it on. I was to do this three times and call them if it didn't work. After the third time, I realiz


... Vacuums

I have a Saeco water kettle and it will not boil water. I just recently started having this problem. When I push the boil button, the water kettle will glow red for 5 seconds. Afterwards, it automatically shuts off.


You have a thermal sensor thats gone bad causing it to turn of ... Vacuums

Won't start I have a miele, model # s2481 red vacuum. It will not start. When the button is pressed it feels normal, but nothing happens, it will not start. Is this a problem my handy husband can tackle?


It is most likely your cord winder. They are a little tricky to fix yourself. A repair shop will probably charge about $50. To fix it. The contacts where the cord winder plugs into the motor need to be cleaned and adjusted. Just don't let your r ... Vacuums

My shark steam cleaner won't "steam out" when I push the button, what's up. Light is on, when I release he safety cap,steam comes out??


... Euro-Pro Ultra Steam SharkTM II Hard Surface Steam Cleaner Vacuum

My Steam Vac won't release any soap water mix


\015\012My model number Bissell is different than yours, but many models work similarly.\015\012 \015\012Capt. Obvious fixes: Water flow often stops unless b ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Shark steam mop will not release water or steam.


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Delonghi Citiz Milk frother not working. After pressing button, red light comes on and heat starts, then after a few seconds red light starts to blink and nothing happens.


Please visit the link provided below :http://www.delonghi.com.au/support/instruction_manuals/EN265BAE_im.pdf ... DeLonghi Vacuums

My vacuum won't stay on. Will start when I push on button but will shut off as soon as button is released.


... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I pushed the on button and kirby g5 starts but when releasing button motor stops


Hello,\015\012You can replace your own Kirby switch with my guide. Here's the link...\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum

My shampooer will not release water when i push the release button on the handle


\015\012\015\012\011\011\011\011\011\015\012\015\012\011\011\011\011\011\011\015\012xpinto ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Bissell carpet shampooer, how do I use it there was no manualI just need bASIC INSTRUCTIONS I'm guessing push button to release shampoo, go over the whole area, scrub as necessary, then it will **** up drity water. Question there is a rinse button Does that mean that I have to go over it again 3x?


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.B ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My shark won't give off steam any more. I push down the handle and nothing happens. Then if I take of the head all the steams bursts out.


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it may not be getting steam to the head...Euro-Pr ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0978 seconds