Having problems with your Bissell 1699 ProHeat Clear View Upright Steam Vacuum ?

Pump how can you check the pump? water does Not spray out of the Hand tool.


Answers :

Replace water pump on bissell 1699
Check the bottom of the tank and make sure that the seal is on the valve and not sitting in the hole where the tanks sits. At the back, is the top and bottom tight together, or is there a gap, should be no gap. Is the mix valve **** turning easily or is it hanging up? Sometimes the flow indicator cap leaks air and needs to be replaced. To get to the pump, you have to take off the top cover. Look and see if any lines are pinched, if not, then replace the pump, also check the pump belt.
\015\012
\015\012c315260.jpg
Repair Help & Product Troubleshooting for Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Pump how can you check the pump? water does Not spray out of the Hand tool.


Replace water pump on bissell 1699 ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Have installed a new pump but seems to have air in the pipes will not spray water from both the main tool and the hand tool


... Bissell Powersteamer 1694 Upright Vacuum

Rug doctor hand tool will not spray ...but it will vaccum....what can I do to get the hand tool to spray again ....tried another hand tool and that didn't work either ....help


... Vacuums

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a


You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Hand tool won't spray for more than 5 seconds


... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

When using the floor configuration, I can't get the trigger to cause a spray of either water or cleaner. When using the tool configuration and the hand device with brushes etc, the spray works well with the hand trigger.


The trigger on the handle for tthe floor configuration has become loose or broken. When you squeeze it, the action pulls a rod that runs down the length of the shaft and goes into the base and allows the water to spray. You need to check and make sur ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell PowerSteamer 1697-1 series. It stopped spraying with the main part and now the hand tool also won't spray any solution--everything seems to be working and it appears to try but it won't spray


... Vacuums

The unit (9400-3) is not spraying water from the lower deck but will spray from the hand held wand. Checked water levels and water/soap dispenser valves which seem to be working fine. Spray nozzles are not blocked. Where do you look now.


Same problem i have got, spent one day on the bloody thing but of no use, the only solution is to spray water from bucket and use the cleaner to **** it up. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?


Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

No spray out of hand tool on hoover f5915-900


Same problem here, did you ever find a solution? ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Bissell 2x Turbo 9300 shampooer. It won' spray from the carpet/floor position. I re-booted it and checked for blockage - nothing. I flushed the hand attachment and got it to spray some water but nothing from the carpet area.


The heater is glogged trust me. It is the size of a dollar bill with seven screws. take it apart and clean the water path also take a small drill bit to the ports of the heater. ... Vacuums

My bissell proheat 12 amp will not spray water on to the carpet,nor will the hand tools spray water?


The water is pumped via the belt that drives the pump. Remove the belt pump on the left side of the unit using a screwdriver and prying upward in the slot in the rear of the belt cover. The belt cover has holes in it. Check to make sure the belt is ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

On a bissell 9400 steam vac i am getting spray from the hand wand but not the floor spray. I checked all the solinoids and lines and switches. I blew throurgh the lines and got no clogs. can you tell me what else can be wrong


... Bissell Vacuums

Hmmm Hi there, I actually had tried everything you mentioned except for the vinegar idea which I'll do when I get back up to my home in Oregon. I checked for pinches, the heater, etc. Water does NOT come out of the accessory tool and only will dispense out of the main area for a second or two..any liquid actually starts filling up the area right behind the nozzles and around the pump instead of OUT of the machine. I checked gaskets, made sure there was a tight seal, and even made sure the little


Check the nozzles to make sure they aren't clogged. Sometimes there is a problem with the flow indicator cap, maybe too tight or not tight enough. Try squeezing the trigger while turning the can one way or the other. If at a certain point it starts ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Hoover steamvac ultra hand tool doesn't spray water from hose - it has steady stream instead of spray


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

My Bisssil cleaner will not pick up the water from the floor. I checked all the trouble shooter helps and evewrything is OK Checked all belts they are OK. It also will not pick up water with the hand held tools, seems as though the vacuum is not working


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My hoover steamvac turbopower 5000ls will not spray for hand tool


My turbo 5200 will not pick up the moister into container to dry does anyone know what the problem may be ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Can't get water to spray out of the hand tool nozzle


When you attach the main suction hose to the front of the machine, you also have to connect the soultion hose to a valve located on the side of the machine. When the machine is running, take a small screwdriver and depress the centre of this valve. Y ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

No suction when i switch to the hand tools they spray out but there is no suction hru the hose what can I do?


When you turned the diverter knob, did the gray diverter valve open up? If not, this would be why no suction, it has to be open for the hose and closed to suction from the floor. Alot of times, the valve breaks and won't work. Is the black ovule s ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

MY 9300-c Bissell Proheat 2X deep cleaner does not pump fluid to floor or hand tools.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Brand new hoover steam vac max extract. brushes won't spin. I have check connections, read the manual and nothing. have the switch to power scrub. works with hand tool.


... Hoover Vacuums

Shampooer not sucking up water- water is spraying out and the hand tool is working but the main body wont **** up and water


Change the selector from hand tool to floor cleaner ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a Bissell Proheat Turbo 2x model 9300. It has stopped spraying at the floor. The hand tools will work so I assume this means the problem is at the base somewhere. I cleaned the nozzles but don't know what to try next. It has always had a problem with dumping too much cleaning solution as well, don't know if this is a contributing factor


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0346 seconds