Having problems with your Bissell 1699 ProHeat Clear View Upright Steam Vacuum ?

Bissell doesn't work with cover on...

\015 I cleaned all the hoses, removed and cleaned heater, and 'without' the main cover on everything works great, the minute I place the cover back on...it quits spraying. Followed all guidelines of where to put hoses..no kinks and ensured Smartmix piston was in place. I am baffled! Any suggestions??\015

Answers :

Did you put the piston on the bottom side of the smart mix knob? If not, put it on, then turn it slightly so it won't fall off. Just before putting the top cover on, put the smart mix knob in the water only spot, then push the top on and make sure that the knob turns back and forth ok. Secure the top down, and put the flow indicator on. Sometimes when you over tighten that cap, it doesn't want to spray right. So just snug it. If you haven't pinched any lines on the base or inside the handle, it should work. Could also be that the flow indictor cap is bad. MAke sure the gasket at the bottom of the tank is on the valve and not sitting in the hole.
Repair Help & Product Troubleshooting for Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

The brush on my bissell helix (model 22C1-2) stopped working all of a sudden today. The hose still sucks and everything. I even cleaned the spinning brush and it still doesnt work. I just bought it in August.


... Vacuums

Bissell doesn't work with cover on...


Did you put the piston on the bottom side of the smart mix knob? If not, put it on, then turn it slightly so it won't fall off. Just before putting the top cover on, put the smart mix knob in the water only spot, then push the top on and make sure ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?


Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

I have a Bissell lift-off revolution. The power won't turn on at all. Tried different outlets. It doesn't work whether the lift-off canister is out of the frame or in the frame. The manual refers to a reset switch but can't find it, even when I took the cover off the main canister unit. Where is the reset button and/or fuse?


I have the same issue too. Brush motor is working and brush is turning on but the vaccum motor is not working. If I take the canister out of the frame then it wont turn on at all. Any help? ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I lent it out (NEVER AGAIN!) got it back and no water squirts out of it in front I looked at it with the cover off but it doesn't come all the way off anyhow nothing looks clogged the belt is all fine too. Clean all the grime is seen and still doesnt work. What's wrong?


It might be pet hair caught in its hose. You might have to disassemble everything just to be sure. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Have a bissell 9400-E and it doesnt spray cleaning fluid from underneath the machine, the hand tool works. have trie purging the machine with hot water in fluid tank and continuously hollding button with no joy can you help please? as my machine is just out of warranty


This may be caused because the pump belt has stretched or broken or the pump is seized and will not turn. Remove the pump belt and turn the pump rotor with your fingers to see it turns freely. If it does then the pump should be OK but the belt ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

We just used our bissell pro heat 25A3/64D9 series and the top half of the handle is not secure. Infact it flies off in my hand as im cleaning the carpet and it almost hit me in the face!!! It just connects to the lower half but there is nothing to keep it secure. If it is not tight the trigger to squirt water doesnt work and I am stopping and starting. It looks like a major design flaw.


I have a replacement pump belt for my Bissell #25A3/64D9\015\012but cannot find the instructions as to how to put a new one on. My son replaced the last belt, and of course he doesn't remember what he did. Is there any way you could please dire ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My bissell velocity height adjustment doesnt work


... Bissell Velocity Bagless Upright Cyclonic Vacuum

Mystery part Bissell 1699-P. I removed the top cover and a part came tumbling out (from the rear of the machine - towards the handle area). I have no idea were this part belongs. I have a schematic of the cleaner but I can not locate the part on it. I tried to copy and paste a picture of the part but that isn't working so I will attempt to discribe the part: There is nothing stampted on the part that I can see. It is plastic(white), 2" long, 3/16" in diamater. One end is U shaped (u-shape is 1/4


One question... you haven't mentioned that the vacuum doesn't work now... as hard as this is to accept... if it doesn't effect the function... forget about it.... i could very well have been something you vacuumed up along the way.\015\012 ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My Windsor Sensor XP12 says the bag is full when it's not. I have removed the hose, brush, and filter and cleaned everything. I can put a bag on without the cover and it works great. However, when I add the bag to the front cover and close the latch the right way, it does not work. I'm thinking that the cover is not seating the bag correctly over the hole, but I can't figure out how to fix it. Any suggestions?


... Windsor SR12 Sensor Bagged Upright Vacuum

I have the Bissell Proheat (7901) It will pick up water and the hand tool works fine. I noticed that the red indicator stopped spinning. Then I noticed no water was coming out. If I put down water using the hand tool, the vacunme will pick it up. When I called Bissell they had me do something with the indicator. When it didn't work they said take it in for repair.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


You need to change the belt(s). You can find the belts for this model here. http://www.vacbelts.com/bissell-proheat-belt-combo-pack.htm ... Bissell 8910 ProHeat Clear View Upright Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC ... Bissell Vacuums

Brush roller not working on Bissell proheat 7920


My brother changed the roller belt, but now the rollers won't stay up so I can move the cleaner and the water isn't getting sucked up. ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I am working on a u5290-900 hover vacuum ,when operating dust leaks out under dirt cup cover. i put a piece of card board on top of cover so extra presure would be applied to the top of cover. this seams to have stoped the leak , before adding the card board the cover seamed to lift at the back when cover was locked into place. what do you think?


Dear Sir:Will be better idea to replace the cup cover. The pice of card will not function for a long time. Proceed before another extra problem coming.God bless you ... Hoover U5290-900 Upright Vacuum

My bissell power trak just stopped working i turned it off and a few hours later i turned it on again and it will not work. I switched over to an outlet i know works and it still didn't work I checked the outlet after and there's still power there. Is there an internal fuse?


... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

Bissell proheat 2x hand tool not working


... Bissell 8910 ProHeat Clear View Upright Vacuum

Not working bissell power pro carpet cleaner not working. was working fine, then I smelled rubber like a belt had broken. does it have a belt that can break.


The bissell shampooers use belts t run the pump and the beater bar. if the master beltbroke which is the one that controls the pump and beater bar then yes the machine will not dispense water or turn the beater bar. it will have to be replaced *the ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

My Filter Queen vaccuum is working but it does not pick up the dirt. The power nozel is working and it sounds like it is working but it doesnt pick anything up?


... Filter Queen Vacuums

One earbud doesnt work and the other works somtimes i can get them both too work by twisting the end of the headphone


... Vacuums

I have a Bissel 9300-C 0714 BC Carpet Shampooer. It was working great and all of a sudden it stopped working. It still sucks up dirty water but it does not spray water onto the carpet. I can get it to spray water through the smallest hand attatchment but not through the large hand held piece on the base of the machine. I really hope you can help me, I am a dog groomer and I really need my machine to work properly. I can get it to spray water out of the smallest hand attatchment but that's all t


The spray jet has become clogged from the soap.... just clean it out. same thing happened to my attachment. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissell Pro heat stopped working


It sounds to me like you may have a bad brush and/or pump belt. Since you are having a simultaneous problem of the brushes not spinning, as well as the solution not spraying, this is the most logical explanation of your problem. Especially if ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Su2914: loss of suction even when cylinder is empty!! doesnt work correctly when pet attachment is added either, only seemed to work ok for first 4 months then loss of suction, will pick up eventually but quite poorly! Should I take it for a service? Thanks


... Samsung Vacuums

Bissell Proheat I have a Bissell ProHeat 12 amp 6 cleaning brush upright and it won't turn on anymore. We have done the basics like making sure the outlets work, etc. Changed it around to different outlets. It is not turning on. Any idea?


Things to check are the cord, switch, and the motor. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0535 seconds