Having problems with your Bissell 1699 ProHeat Clear View Upright Steam Vacuum ?

How to remove heater cover on bissell clearview steam cleaner


Answers :

Repair Help & Product Troubleshooting for Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to remove heater cover on bissell clearview steam cleaner


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissell ProHeat Clearview Steam Cleaner - need steps to clean the clear input area. I have removed the four screws and need to know how to finish the removal of the clear plastic input area.


For the clear outer nozzle, there are 2 screws holding it in place. Remove those, then from the bottom lift it up. Sometimes the seal holds it really tight and you may have to carefully pry on the sides until it loosens up. Then when you put it ba ... Bissell Vacuums

How to remove cover on main unit of Bissell proheat clearview carpet cleaner


... Bissell 8910 ProHeat Clear View Upright Vacuum

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.


Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Bissell pro heat carpet cleaner clear cover removal


Just lift it up probably suction holding it ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

HOW DO YOU REMOVE THE TOOTHED DRIVE WHEEL FROM THE BRUSH MOTOR ON MY BISSELL 9200E CARPET CLEANER. ALSO IS THE ATTACHED UNIT THE MICRO SWITCH? WHY IS THE MOTOR COVER STILL ATTACHED TO THE FRAME WHEN ALL 4 OFF SCREWS ARE REMOVED JIM


It is a snap lock plastic cap on mounted to the frame. ... Bissell 9200 Upright Vacuum

Bissell 1699 ProHeat Clearview Steam Cleaner won't pick up


Usually if the water isn't being sucked up is either the filter in the lid of the tank is clogged, or the gasket that sits on top of the clear window nozzle and the tank is missing. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Mystery part Bissell 1699-P. I removed the top cover and a part came tumbling out (from the rear of the machine - towards the handle area). I have no idea were this part belongs. I have a schematic of the cleaner but I can not locate the part on it. I tried to copy and paste a picture of the part but that isn't working so I will attempt to discribe the part: There is nothing stampted on the part that I can see. It is plastic(white), 2" long, 3/16" in diamater. One end is U shaped (u-shape is 1/4


One question... you haven't mentioned that the vacuum doesn't work now... as hard as this is to accept... if it doesn't effect the function... forget about it.... i could very well have been something you vacuumed up along the way.\015\012 ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Trigger not activating the steam cleaner bissell powerstream clearview


... Bissell Powersteamer 1694 Upright Vacuum

Need free manual for bissell steam cleaner clearview


BISSELL User’s Guides can be downloaded at www.bissell.com\012On the front page under Customer Service click on User’s Guides and enter the model number of your unit.\012User Guide will be displayed as a PDF file. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

How do you remove the back cover on the Hoover Steam Vac Dual V floor cleaner?


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Bissell Steam Cleaner that is not sucking up the water when cleaning. I used a full container of water and when it was empty I emptied out the water, only to find very little dirty water in it. I noticed the window, as i used it, seemed like it wasnt sucking up the water. I took the plastic cover off to clean it (it didnt look very dirty in the first place), an i noticed that the grey plastic flap was on but not moving up or down. I thought there may be dirt in it that prevented it from


... Bissell Vacuums

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth


When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

I have a Bissell ProHeat 2x, and I did something dum. I had some powdered cleaner that said it works with carpet cleaners-well I mixed it in-and the next time I tried to use it, nothing came out. So, I took it part to check what was wrong-and found out that the powdered cleaner solidified in places. I cleared the nozzels, nothing. I think the solenoid, between the heater and nozzels is pluggd, and possibly the heater. I've got a question-could I use CLR to clean the heater, with replacing t


Heck yeah, give it a shot. Try running some water through it too- fill it up, heat it just to where it's hot and unplug it, shake it around and dump it out. Repeat. You might have to get a wire or something to go through and get the powder loosened b ... Bissell Vacuums

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?


... Bissell 8910 ProHeat Clear View Upright Vacuum

Hi I own a Bissell Proheat Powersteamer pro-tech with a turbobrush. I have been using "bissell multi-allergen removal formula for carpets and upholstery." I ran out of that last night. Today I went to walmart looking for more. Everything I found said "2x Ultra Concentrated Bissell multi-allergen." I'm confused on where to add the cleaner. I have a water tank and a separate soap tank. The instructions on this new cleaner bottle say to add 4 capfuls for the formula tank and dilute with hot tap wat


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

How to remove cover from a bissell 1660z


... Vacuums

How do i repair heater on vax steam cleaner - McCulloch MC1246 Handheld Steam Cleaner


... McCulloch MC1246 Handheld Steam Cleaner

Bissell steam cleaner water leaking - Bissell 1699 ProHeat Clear View Upright Steam Vacuum


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Brush will not spin on the steam cleaner - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

HI, I'm looking to buy a Bissell 9500 steam cleaner. I was wondering can you use the steam cleaner as a regular vacuum? The store manager says yes But I'm unsure..


I agree its not wise to use machine as a standard hoover thus it can cause overheating and other problems. best stick to what its meant for :-) ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

How do i put belts on a bissell powerbrush steam cleaner?


If this is the model i'm thinking of. Make sure the units unplugged from the wall. There should be about six phillips head screws to remove. The motor should now be exposed. This is a good time to clean up the inside of the unit. Use liquid wrench or ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Water wont come out fo the steam cleaner. - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


Try adding a table spoon of salt to the water. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Airlock in my carpet cleaner bissell proheat - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Bissell carpet cleaner not dispensing water - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0765 seconds