Having problems with your Bissell 1699 ProHeat Clear View Upright Steam Vacuum ?
Bissel pro heat carpet shampooer 1699
\015 Hello, I missed placed the directions on how to operate / use my bissel pro heat ,can you help ?/ Thanks\015
Push the foot pad handle release on the left side lay the handle all the way back.Then lift the handle on the center bucket pull out and fill with hot tap water only no soap in the hole that fills up the plastic bladder.Flip the handle back down so that it locks the lid on. On the right side is a smaller soap tank just pull it up and unscrew the top and put your soap in it then replace.Set the dial right beside it to either water only ,or high traffic or ,regular.The soap dispenses automatically saving you from having to mix the solution.Turn both switches on and make a forward and back pass holding the trigger release the trigger go over the area just soaped until most of the water is sucked up. The little red circle on the left side is supposed to be turning if the water and soap are being sprayed out.Repeat and have fun
The following link is the owners manual. Hope it helps! Post back.
Repair Help & Product Troubleshooting for Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Bissel pro heat carpet shampooer 1699
Push the foot pad handle release on the left side lay the handle all the way back.Then lift the handle on the center bucket pull out and fill with hot tap water only no soap in the hole that fills up the plastic bladder.Flip the handle back down so t ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
We have a Bissell Pro-Heat 9200 2X Carpet Shampooer. When you start to shampoo the carpet it runs water for a minute and then quits and won't spray any more water.
The heater is clogged. Take off body assembly. There is a silver part in there the size of a dollar bill. with seven screws. That the heater element. It is clogged known problem on there bissels. Crappy design for one. But most causes are not useing ... Bissell Vacuums
I have a bissell pro heat carpet shampooer model # 8910 and it will not spray any solution out what could the problem be its only been used twice without any problems
Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.B ... Bissell 8910 ProHeat Clear View Upright Vacuum
Brushes not spinning on my Bissell carpet shampooer (pro heat turbo 2X)
Dog hair may cause this, clean this unit, take sissors and cut hair. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
Bissell pro heat steam carpet cleaner, not releasing water.
That means that you need to replace the pump belt. Here is the belt you \012need and a manual you can view:\012\012Bissell 7901 Belt and ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Replacement electric motor for Bissell Pro Heat 2x Select carpet
Bissell proheat i can spray solution from the handle but it has no suction help ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums
Bissell pro heat 2x multi surface carpet cleaner making spots
Maybe there's not enough vacuum or it hasn't been primed enough. I have a proheat that drove me crazy till I started leaving the heat switch on. I get wads of carpet fiber that mat around brush and spit out on the carpet, so I frequently remove them ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Bissell pro heat will not extract water from the carpet
Try checking the top section of the machine (where the dial is located to switch it from floor to tool) and there is a little red plastic piece about 1 inch square on the inside of it. This is a lint filter that has a little door on it. Open the do ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.
The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
Bissell Pro-Heat Pro-Tech Carpet Cleaner
Put the piston on the bottom part of the knob, You want the the knob to be at the water only setting when it goes into the slot. After the top is pushed all of the way on, turn the auto-mix knob to see if it is turning easily. If it doesn't stop, ... Vacuums
I need a manual for the bissell pro heat carpet cleaner #7091H. I used it but I can not get it to **** the dirty water out of the carpet. What am I doing wrong?
Try here:\015\012\015\012http://www.bissell.com/Product_Search.aspx?Criteria=pro+heat+carpet+cleaner\015\012 ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Bissell pro heat carpet cleaner, won't move forward. both belts working. is there something that is suppossed to hold the brush bar down so the carpet cleaner uses that as it other set of "wheels"
... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
My carpet cleaner bissell pro heat wont extract the water from the carpet
1) Remove the Tank-in-Tank Assembly and place your hand over the motor intake valve. This valve is located next to the Floor Nozzle gasket (at the top of the Floor Nozzle window) and behind the SmartMix Bottle. If you feel vacuum-like suction at t ... Bissell 8910 ProHeat Clear View Upright Vacuum
I have a Bissell pro heat carpet cleaner, the water spray wont come out to clean the carpet.
Bissel proheat turbo 2x ipx4.\015\012\015\012I don't have the instruction the this machine if you could help me with where to put the water and cleaning solution and how much, also how to use it.\015\012\015\012Thankyou, ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
My bissell pro heat 2x does not **** up the water from either the upholstery cleaner or carpet cleaner. Any thoughts as to why? The water and heat functions work it just does not pick up
First check the motor duct gasket. The motor duct gasket is visible once the tank is removed. It is located underneath the handle on the top of the base of the machine. It has a black rubber coating around it. If there is no suction there please let ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
I have a bissel pro heat carpet cleaner that doesn't spray cleaner solution, everything else works, but I don't know whether it's the pump or the heat unit.I'm assuming that the pump unit must be bad since all the connections are in place, but from the view of the pump I am not sure what drives it.
I have a bissell steam cleaner 1698. I have had it for a few years. First and last time I used it I was sorely disappointed. How was the word steam integrated into the name. I saw no steam. Ended up soaking my couch, soaked spots on my rug and n ... Bissell 1693 PowerSteamer Upright Vacuum
I was given a Bissell Pro Heat Turbo 2x Microban carpet cleaner, but I don't have the instructions on how to use it. It's Model 9300-1. I would like to know how much carpet cleaner I should put in it.
... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
When I clean my carpets and hold the trigger only water comes out, there is no soap leaving the container . I have a Bissell pro heat 2X carpet cleaner.
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Pro hEat will not **** up water from carpet - Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
Check the vac motor hose could be clogged? does the vacuum motor turn on? check the vac motor on switch for power using an ohms meter.could have a bad vacuum motor or micro switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
Bissell 2x pro heat will not **** water out of my carpet
Try turning the dial on the front that says tools. That solved the same problem for me!!!! ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Bissell pro heat carpet cleaner clear cover removal
Just lift it up probably suction holding it ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Need free manual down load for Bissell 8910 pro heat carpet cleaner
BISSELL User’s Guides can be downloaded at www.bissell.com\012On the front page under Customer Service click on User’s Guides and enter the model number of your unit.\012User Guide will be displayed as a PDF file. ... Bissell 8910 ProHeat Clear View Upright Vacuum
Bissell Carpet Cleaner pro heat- water doesnt come out
The screw that is located in the center of the handle, that holds the assecory hose holder must be tight. My screw was missing, put one in and cured the problem. Sounds stupid but it worked. Got this idea off the Bissell web site. Also if you have a ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
Instructions for using Bissel Pro Heat shampooer.
Manuals can be downloaded from the Bissell website ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum