Having problems with your Bissell 1699 ProHeat Clear View Upright Steam Vacuum ?

Smart mix plunger bissell 1699

\015 Unit would not dispense water or cleaner. After taking the unit apart twice I found the heater was blocked. In doing this the plunger fell off. I was able to put it back in place but I must be positioning the plunger wrong. I get water but no matter what position I turn the know no cleaner will dispense.\015

Answers :

This is what happened to me. The heater had to be cleaned. Easy fix.
Check your wiring. I have a photo of the correct wiring if you'd like it for reference,
Repair Help & Product Troubleshooting for Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Smart mix plunger bissell 1699


This is what happened to me. The heater had to be cleaned. Easy fix. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Replacing smart mix plunger bissell proheat model 7901 procedure for proper installation


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.B ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell proheat 1698 reassembly, smart mix piston, new pump?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissell proheat pro tech model 7901-3 smart mix dial and valve assembly


Turn the knob to the water only, put the piston on the bottom of the knob then turn it slightly so it doesn't fall off, Start to put the cover on, when it is straight, turn the knob to the water only selection and push the top all the way down. The ... Vacuums

I purchased a Pro Heat self propelled Bissell rug cleaner model 7950 from Target wherehouse on 4-26-06. I used it once and all was fine. The next time that I went to use it the smart mix for the cleaning formula would not dispense formula.I called Bissell consumer services and was told to take it to Starks Vaccumn in Sherwood, Or. That was on 10-30-06 They said that it was working so I tried it again and not a drop of formula was or has been used since.I took it back 2-13-07 and the replaced the


I assume that it is spraying water? Is the smart mix knob turning freely from one point to the end? If not then there is a problem with the smart mix asm. With liquid in the soap bottle, push the valve in to see if liquid comes out ok, couild be ... Vacuums

I need a part number for bissell proheat 2x 8930 smart mix valve


... Bissell 2X Proheat 9200 rug cleaner

Can't reassemble!!! Long story as short as possible- I removed the hood from my Bissell 1699 and can't seem to get it back on correctly. The "Smart Mix" knob and it's parts seems to be the problem. How does this line-up, or what is the best way to put it all back together? Thanks, Josh


The piston is put on the bottom of the smart mix knob, turn the knob to the water only setting, then put the top housing back in place making sure that the piston went into the slot, after the top is all of the way down, turn the knob, if it turns ea ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

How do I replace the Smart Mix knob on a Bissell shampooer


... Bissell Vacuums

The smart mix bottle is not dispensing any fluid. I have been using this Bissell 8910 for 6 years. The cap and seal seem to have all the parts. thanks -LaRie-


... Bissell 8910 ProHeat Clear View Upright Vacuum

How do you get the smart mix dial to line back up when replacing the top plastic cover on a bissell pro heat pet.


First, insert the black plastic control valve all the way into the hole. Make sure that the rounded face with the cut in it is facing toward the tall part of the chamber/hole where you inserted the valve. Try to line up the dial with where the thre ... Bissell 8910 ProHeat Clear View Upright Vacuum

Smart Mix selector


I figured it out,since you nor Bissell was of no help. It turns out to be quite easy. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I THINK THE SMART MIX PISTON IS INSTALLEDS WRONG


It has the rubber seal and the container releases fluid when it depressed.... bipolar lol..\015\012\015\012fill it with hot water and prime the machine.. don't use soap just try lear the lines.. always run hot water through your machine ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Bissell Pro-Heat Pro-Tech Carpet Cleaner


Put the piston on the bottom part of the knob, You want the the knob to be at the water only setting when it goes into the slot. After the top is pushed all of the way on, turn the auto-mix knob to see if it is turning easily. If it doesn't stop, ... Vacuums

Smart mix what is the trick to connecting the smart mix?


Glad you did. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Connecting a BISSELL AUTO MIX PISTON TO A AUTO MIX KNOB


Take of the housing ,turn it over and you will see the under side of the auto mix dial , Then turn the auto mix dial to rinse only;\015\012On the top of the piston you will see a small slot , this fits into \015\012the out ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Smart Mix Dial - Reassemble Cover


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell - Model 1697 - Powersteamer Pro - Carpet Cleaner I took the unit apart to replace some broken pieces and I can not seat the bottom to the top without properly engaging the soap/water mixer. What is the proper assembly procedure. What is the orientation of the water/soap mix valve when I seat the top to the bottom? The soap/water mix valve needs to engage the knob screw threads but this assembly is a blind operation. Do I turn to the soap/water mix knob to water only then seat the


Hi,\015\012http://dl.owneriq.net/7/7e477b7e-4440-49cf-a219-b68d301549e3.pdf\015\012This diagram will help you see the diagram plus the part assembly no and place it accordingly.I have also given link for Bissell - Model ... Vacuums

Replacing Smart Mix knob


The knob itself will only go in one way, What I was talking about is when you put the top cover back on, the knob should be in the water only position. This way the piston (on the bottom of the knob) will go into the slot correctly. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

The solution in my smart mix will not mix with water and the button just keeps going round and clicks and will not stop on either water or solution.


The smart mix knob is connected to a piston that slides up and down into the automix assembly. This piston has come off of the smartmix knob and left the unit on water only setting. Sometimes the smart mix knob breaks on the ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Cleaner solution in smart mix tank not mixing with the water from the bladder. All tanks are seated properly


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I have Bissell Model 1699-R Proheat carpet steam cleaner one of the tubings that connects into spray got mixed with some tubings during tubing replacment to the point that tubing that is conected into flow indicator cap does not turn at all to show if the chemical is sprying or not.i am looking mainly for tubing water/chemical diagram in order to verify the right connection.please help if you can bissell user. thanks


... Vacuums

I have a bissell 1698 powersteamer. i have already cleaned heater and completely cleaned all parts , checked the mix piston, checked belt. it will not shoot water or mix. the motor runs, it will **** water and the brush turns. is it the pump and does the pump just shoot the soap?


Pump is probably bad. When you put the lid back down, did you put the piston on the bottom of the smart mix knob? Also the smart mix knob should be in the water only selection when the top is pushed all of the way down. Also sometimes the flow ind ... Vacuums

FILLING INSTRUCTIONS. I HAVE A BISSELL PROHEAT PLUS 12 AMP CLEANER. HAVE LOST MY MANUAL. NEED INFO ON FILLING THE MACHINE. DO I MIX THE BISSELL CLEANING SOLUTION WITH THE WATER? IS THERE A SEPERATE PLACE TO PUT THE CLEANING SOLUTION, IF SO HOW MUCH SOLUTION PER WATER CONTENT. THANKS


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Bissell ProHeat 7920 Carpet Cleaner


I managed to sort this. The small plunger valve sits in a little square crevice next to the smartmix dial - it does NOT sit in the middle as it first seems. You then have to get the lip of the smartmix dial to sit in the cut out on the side of the pl ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Smart mix valve reassebly and alignment


Have the piston on the screw threads, put the knob on the water only setting, then after the piston is on, turn slightly so it doesn't come off, just before you put the housing all of the way down, turn the knob back to the water only setting and the ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0543 seconds