Having problems with your Bissell 1699 ProHeat Clear View Upright Steam Vacuum ?

Smart Mix selector

\015 Replaced the Bissell Proheat Pump on Model 1699-P. My problem is I\015\012can't get the Smart Mix selector to engage the control valve when I\015\012reinstall the cover, any suggestion would be appreciated.\015

Answers :

I figured it out,since you nor Bissell was of no help. It turns out to be quite easy.
There is a groove under the control knob in the main housing which the piston will slide into until it reaches the part that turns.Place on water only setting and slightly lean piston back so the small groove engages the wheel that turns then place housing assembly above main unit and lower until piston is lined up above piston hole.
\015\012Tighten screws and check for easy yet slight hold on mixture knob.
Repair Help & Product Troubleshooting for Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Smart Mix selector


I figured it out,since you nor Bissell was of no help. It turns out to be quite easy. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Smart mix what is the trick to connecting the smart mix?


Glad you did. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Replacing Smart Mix knob


The knob itself will only go in one way, What I was talking about is when you put the top cover back on, the knob should be in the water only position. This way the piston (on the bottom of the knob) will go into the slot correctly. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissell proheat pro tech model 7901-3 smart mix dial and valve assembly


Turn the knob to the water only, put the piston on the bottom of the knob then turn it slightly so it doesn't fall off, Start to put the cover on, when it is straight, turn the knob to the water only selection and push the top all the way down. The ... Vacuums

The solution in my smart mix will not mix with water and the button just keeps going round and clicks and will not stop on either water or solution.


The smart mix knob is connected to a piston that slides up and down into the automix assembly. This piston has come off of the smartmix knob and left the unit on water only setting. Sometimes the smart mix knob breaks on the ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Cleaner solution in smart mix tank not mixing with the water from the bladder. All tanks are seated properly


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Bissell proheat 1698 reassembly, smart mix piston, new pump?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I THINK THE SMART MIX PISTON IS INSTALLEDS WRONG


It has the rubber seal and the container releases fluid when it depressed.... bipolar lol..\015\012\015\012fill it with hot water and prime the machine.. don't use soap just try lear the lines.. always run hot water through your machine ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Smart mix valve reassebly and alignment


Have the piston on the screw threads, put the knob on the water only setting, then after the piston is on, turn slightly so it doesn't come off, just before you put the housing all of the way down, turn the knob back to the water only setting and the ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Broken Smart Mix Dial-How to replace


You will have to remove the top, the knob screws on but has a stop tab. Is the plastic below the knob ok, if not then you need to replace the top cover. After you replace the knob, then put the piston on from underneath, have it set to water only s ... Bissell 7950 ProHeat Upright Wet/Dry Vacuum

I need a part number for bissell proheat 2x 8930 smart mix valve


... Bissell 2X Proheat 9200 rug cleaner

Smart mix plunger bissell 1699


This is what happened to me. The heater had to be cleaned. Easy fix. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Can't reassemble!!! Long story as short as possible- I removed the hood from my Bissell 1699 and can't seem to get it back on correctly. The "Smart Mix" knob and it's parts seems to be the problem. How does this line-up, or what is the best way to put it all back together? Thanks, Josh


The piston is put on the bottom of the smart mix knob, turn the knob to the water only setting, then put the top housing back in place making sure that the piston went into the slot, after the top is all of the way down, turn the knob, if it turns ea ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Replacing smart mix plunger bissell proheat model 7901 procedure for proper installation


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.B ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

How do I replace the Smart Mix knob on a Bissell shampooer


... Bissell Vacuums

How do you get the smart mix dial to line back up when replacing the top plastic cover on a bissell pro heat pet.


First, insert the black plastic control valve all the way into the hole. Make sure that the rounded face with the cut in it is facing toward the tall part of the chamber/hole where you inserted the valve. Try to line up the dial with where the thre ... Bissell 8910 ProHeat Clear View Upright Vacuum

I purchased a Pro Heat self propelled Bissell rug cleaner model 7950 from Target wherehouse on 4-26-06. I used it once and all was fine. The next time that I went to use it the smart mix for the cleaning formula would not dispense formula.I called Bissell consumer services and was told to take it to Starks Vaccumn in Sherwood, Or. That was on 10-30-06 They said that it was working so I tried it again and not a drop of formula was or has been used since.I took it back 2-13-07 and the replaced the


I assume that it is spraying water? Is the smart mix knob turning freely from one point to the end? If not then there is a problem with the smart mix asm. With liquid in the soap bottle, push the valve in to see if liquid comes out ok, couild be ... Vacuums

Smart Mix Dial - Reassemble Cover


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Flow indicator is not turning and the water from the bladder does not spray out only the smart mix container emties


... Bissell 7950 ProHeat Upright Wet/Dry Vacuum

The smart mix bottle is not dispensing any fluid. I have been using this Bissell 8910 for 6 years. The cap and seal seem to have all the parts. thanks -LaRie-


... Bissell 8910 ProHeat Clear View Upright Vacuum

Bissell - Model 1697 - Powersteamer Pro - Carpet Cleaner I took the unit apart to replace some broken pieces and I can not seat the bottom to the top without properly engaging the soap/water mixer. What is the proper assembly procedure. What is the orientation of the water/soap mix valve when I seat the top to the bottom? The soap/water mix valve needs to engage the knob screw threads but this assembly is a blind operation. Do I turn to the soap/water mix knob to water only then seat the


Hi,\015\012http://dl.owneriq.net/7/7e477b7e-4440-49cf-a219-b68d301549e3.pdf\015\012This diagram will help you see the diagram plus the part assembly no and place it accordingly.I have also given link for Bissell - Model ... Vacuums

We have a Singer 626 sewing machine. It's an old mechanical machine with heavy metal parts. The stitch selector was stuck, I removed the top and helped the selector to move. when I had to move the selector again, it was stuck and I pushed too hard and broke a component. I can fix the machine if I had a repair manual. I need to buy a repair manual. How and where can I get one? Thankjs Charlie PS. Im pretty mechanicly inclined and I was able to clean the machine and get it to work after


... Vacuums

Connecting a BISSELL AUTO MIX PISTON TO A AUTO MIX KNOB


Take of the housing ,turn it over and you will see the under side of the auto mix dial , Then turn the auto mix dial to rinse only;\015\012On the top of the piston you will see a small slot , this fits into \015\012the out ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I was mixing a cake mix on an old Kitchenaid Hobart Mixer Model 4 C for 5 Minutes and then white smoke started to come out. I don't think the mixer had been used in many years. Is this repairable or should I junk it. Thanks, Bonnie


... Vacuums

I have a Krups handmixer. 3 Mix 4004. I am looking for an attachment for preparing dough bread mix. Where can find this- if possible in the UK?


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0129 seconds