Having problems with your Bissell 1699 ProHeat Clear View Upright Steam Vacuum ?

Replace the switch that controls hand tools to the upright unit

\015 My carpet cleaner is not sucking up the soapy water and dirt I believe due to the switch that controls the vacume direction from the hand tools to the unit. I believe the switch is broken and I was looking to get a manual of the parts.\015

Answers :

If that flap isn't moving when you turn the knob for floor or hose, then yes it is broken, part #2136988 is the diverter valve. You will have to remove the top cover, it mounts on the underside of it.
Repair Help & Product Troubleshooting for Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replace the switch that controls hand tools to the upright unit

If that flap isn't moving when you turn the knob for floor or hose, then yes it is broken, part #2136988 is the diverter valve. You will have to remove the top cover, it mounts on the underside of it. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Unit-hand tool switch

Maybe this picture will help, most vacuum repair shops should be able to get the part you need. You can also try bissell.com. \015\012\015\012 ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My wall ceiling fan's control unit UC 9051T failed. Light switch button does not work. If I replace it with some generic universal unit, do I need to replace transducer located in the fan housing also, or all of them are compatible? Thanks in advance. M

First, you didn't say you checked that the bulb worked. Is that burned out?\015\012\015\012If bulb is ok, you will have to make sure the switch is matched with the fan (ususally a set of 4, 6 or 8 micro-switches have to be set the same i ... Vacuums

We have a kenmore model 11635922500. It will not turn off. Have replaced the keyboard and it still doesn't. Will switch to Intel clean, hand tools and all others, but will not turn off?

... Kenmore Vacuums

I have a Hoover SteamVac F5914-900 SpinScrub... The last time I used the hand tool attachment, it worked fine. Just tried to use it again, and now I only drips of water will come out of the hand sprayer, if that. I have tried prepping it for up to 15 seconds like the manual says... no luck with that. Also it is making a big puddle on the floor, probably because the brushes on the main unit keep spinning when I am trying to use the hand tool which I dont think they are supposed to do? Can a

The brushes can be turned off on most of them via a switch on the hood. There shouldn't be water coming out onto the floor unless you are pulling the trigger at that top. You probably broke this when attempting to use the tools. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin

... Vacuums

Replace control switch on Dyson 04 Model

You have to remove the yellow on /off switch first. This is actualy a cover to the switch below. I removed mine with x1 of the centre prongs of a fork. Bend the centre prong to 90 degress to the fork handle, and put a tiny kink at the end of that pro ... Vacuums

I have a Hampton Bay Midili fan which I just installed about a month ago and it was working fine. A few days ago when I flipped the switch on the light flickered on and off consistently until I turned the switch off. The remote also stopped working to control the fan and light. Since this model only can be controlled by the remote I am worried I will have to replace the remote already after only 1 month!

In many of these remote controlled lamps you cant use the new spiral light bulbs .. you can only use standard incandescent lights .. if thats not the trouble then you may indeed have a bad controller (in the fan) .. there is probably at least a 90 d ... Vacuums

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

We recently bought a home with a 52" Hampton Bay Berlini Model 729 395 ceiling fan with a light that operates on a remote control. There is also a wall switch plate with two circular controls - one pushes and spins, the other turns with 4 clicks. We can not get the light or the fan to operate using either the switches or the remote. We have checked the circuit breaker. The manual that came with the unit - provided to us from the previous homeowner - really only describes how to install the uni

Nancy do you want to sell the Berlini fan if youstillo have it? ... Vacuums

My Kenmore progressive upright vacuum, model 11635923500 has a problem with the brush rotating. Sometimes the brush will not rotate until the unit in lowered way down, like the activate switch has rotated. Can I get inside the unit to check the switch, if so were do I look

... Kenmore Vacuums

Our dustbuster (dont' have model number with me-sorry) won't turn off when I pull back on the switch handle. I disassembled the unit and realize that the tab on the switch handle that pulls back on the internal switch handle to turn it off is not strong enough for its simple task. Does B&D have a proper replacement part?

If you can provide a model number, I can check availability of the switch and can either order it for you, or supply the B&D part number and you can order it from most local vacuum shops in your area or from Black & Decker direct online: ... Black & Decker 15.6 Volt DustBuster Vacuum

Replacing Switch & cord on OLD Eureka upright 403B or 403S (can't read)

Http://geeksquad.fixya.com/support/t581907-replacing_switch_cord_old_eureka\015\012Generic problem for all Vacuums ... Vacuums

NuTone CVF353W: unit clicks when switched on, but won't run. Replaced motor.

... Broan-NuTone CV353 Central Vacuum

Suction only coming through the wand when its replaced its not switching back to the upright. I have a dyson DC28 animal

Hi there, it's Jack at Dyson.I'm sorry to hear your DC28 doesn't seem to be working correctly. It sounds as though the change-over valve may be jammed - this diverts the suction to the hose when you remove the wand, and back to the cleaner he ... Dyson DC28 Animal Bagless Upright Vacuum

Replace turbine or control switch for Hoover F7412-900?

... Hoover F7412900 Upright Vacuum

Hooked everything up per directions. I plugged it in to the closest electrical outlet and nothing happened. The lights did not light up, the connected wall control and sensors leds do not light up. It appears the unit doesn't have power. The electrical outlet socket is fine as everything else I plug into it works fine. I have tried every other electrical outlet available. The unit won't power on from any outlet, and all of those outlets run other things, like power tools an refrigerators

Dear Davehibshman,Firstly; dismantle the plug and replace the fuse with the same rating as the one you have just taken out. Replace the plug cover, put the plug into the socket and try again. If this doesnt work, there may be a problem wi ... Vacuums

The water dispenser must have been left plugged in and the hot water switch on without any water bottle on the unit because a plastic part inside got warped and now the unit tries to heat the whole 5 gallon jug of water. I want to replace the inside plastic part but I don't have the manual and don't know which part no. to request or where to send my request for parts.

Please state the brand and model number of your water dispenser, so I could give you the exact part and lead you where to purchase it.Post back ... Vacuums

The electronics in my Sunbeam TA200A Toaster is playing up. The Toaster is sometime popping the toast up after the right amount of time, but sometimes it pops up a minute later than it should (burning the toast) I have open up the control panel buttons and inspected the array of transistors and resistors that is used for the timing mechanism and a visual inspection doesn't indicate a problem. I am keen to replace the 2 transistors on the control unit (the resistors are unlikely to fail) but I ne

... Vacuums

My Kenmore canaster vacuum Mod# 116.25513506 runs continously when plugged in regardless of the on/off hand controlled switch.. Disconnecting the switch located on the hose assembly has no affect of the continous vacuum operation. What component in the electric motor circuit is at fault and what would be the cost of repair?

... Kenmore Vacuums

I have a wireless thermometer made by Viking (CE 0197). Have replaced the batteries of the remote sensor RF wireless. In the battery compartment there is button TX and a slide switch for position 1,2,3. Have replaced batteries pused button but no results of recording. Could you help me what to do to make the unit work again. Thank you

... Vacuums

Hoover SteamVac Plus 1200 upright hot water extractor Water/carpet cleaner applying o.k. Suction on the "floor" does not work. Suction on the hand tool works somewhat, but water is not collecting in the bucket. There is suction coming from the floor but water is not going into the bucket. It does not appear to be clogged because I can feel with my hand that air is flowing from the floor. The water is not being sucked into the bucket.

... Hoover Vacuums

Self-propel switch arm broke off where control cable was attached. Looking for instructions as to how to gain access to that switch arm to replace it.

Greetings from GoVacuum,\015\012\015\012This is a farily common repair on this model. What ends up happening is that when someone picks up the vacuum cleaner by the handle of the machine, which on this model also is the controller for th ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

The switch on the wall only works to control the fan and not the light- it won't turn off the ligght. I replaced the switch but it did not solve the problem

If this is a new installation and there was only one switch on the wall, say to control a light that was once there, then you have that switch hooked up only to the fan.\015\012If you want to control the light as well, it has to be wired up at the bo ... Vacuums

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.

Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0763 seconds