Having problems with your Bissell 1699 ProHeat Clear View Upright Steam Vacuum ?

Unit-hand tool switch

\015 Is there a diagram showing how to take the unit apart to fix the switch that controls the vacume source, hand tools or unit. I believe the switch on my unit is broken and needs replaced. Then, where do I get the part that is broken?\015

Answers :

Maybe this picture will help, most vacuum repair shops should be able to get the part you need. You can also try bissell.com.
Repair Help & Product Troubleshooting for Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Unit-hand tool switch

Maybe this picture will help, most vacuum repair shops should be able to get the part you need. You can also try bissell.com. \015\012\015\012 ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Replace the switch that controls hand tools to the upright unit

If that flap isn't moving when you turn the knob for floor or hose, then yes it is broken, part #2136988 is the diverter valve. You will have to remove the top cover, it mounts on the underside of it. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a Hoover SteamVac F5914-900 SpinScrub... The last time I used the hand tool attachment, it worked fine. Just tried to use it again, and now I only drips of water will come out of the hand sprayer, if that. I have tried prepping it for up to 15 seconds like the manual says... no luck with that. Also it is making a big puddle on the floor, probably because the brushes on the main unit keep spinning when I am trying to use the hand tool which I dont think they are supposed to do? Can a

The brushes can be turned off on most of them via a switch on the hood. There shouldn't be water coming out onto the floor unless you are pulling the trigger at that top. You probably broke this when attempting to use the tools. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Brand new hoover steam vac max extract. brushes won't spin. I have check connections, read the manual and nothing. have the switch to power scrub. works with hand tool.

... Hoover Vacuums

Where do I connect the hose for the hand tools to the unit' on the9514-900

There is a piece that slides out on the front of the waste water compartment. Slide this piece out, place the "v" shaped end of the hose into the compartment, replace the lid and you are good to go. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

No suction when i switch to the hand tools they spray out but there is no suction hru the hose what can I do?

When you turned the diverter knob, did the gray diverter valve open up? If not, this would be why no suction, it has to be open for the hose and closed to suction from the floor. Alot of times, the valve breaks and won't work. Is the black ovule s ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I want to take apart a kone dirt devil and i know how it has to be done but i dont have 5 hands to do it. there has to be a tool that presses on the four sides of the case so you can slide the motor unit out. can you help me with this

... Dirt Devil KONE Cordless Hand Vacuum Vacuum

We have a kenmore model 11635922500. It will not turn off. Have replaced the keyboard and it still doesn't. Will switch to Intel clean, hand tools and all others, but will not turn off?

... Kenmore Vacuums

Rug doctor hand tool will not spray ...but it will vaccum....what can I do to get the hand tool to spray again ....tried another hand tool and that didn't work either ....help

... Vacuums

The unit does not start when I turn on the switch on the handle. The power nozzel runs, but the vacuum motor does not. The reset button is not popped, there is 110volts to the unit, and I tried flicking the switch inside the unit underneath the filter with no responce.

... Electrolux Centralux Vacuum

Unit has power from Plug to unit. Current flows all the way to switch and switch seems to be ok but unit will not turn on. Wife says it was cutting on and off when moving it around. Checked conntec

You either have a bad switch oir you have a short in the cord.plug it in and turn it on then move the cord around from top to bottom and see if it acts up..if not tap on the switch afew times and if it cuts out then the switch is bad.try to plug it i ... Vacuums

I have a Hoover Platinum carpet cleaner, and it has stopped dispensing cleaning agent and water. This model has a separate tank for water and separate tank for shampoo dispensing. It also has a power hand unit that dispenses shampoo. All along the hand unit has continued to dispense shampoo. Symptom #1, the water tank seemed to be taking on shampoo, as it was getting sudsy. Symptom #2 - On wash mode, nothing would come out, on Rinse mode, sudsy water would come out. Later, symptom #3 - not

Somewhere on the outlet is a control tap thats driven by a rubber band and something is up with this control ,best advice here is put it in the boot of the car and take iot to a hoover dealer ,they will do it seconds for you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??

... Kirby Vacuums

Hoover Max Extract LS F6056900 Hand Tool not working / Cleaning Solution I need to know what I need to get in order to have the hand tool work on this model. Also, what cleaning solution is best for pet stains? Tried cleaning, pre-treating with Spot Shot and towel and/or scrub brush, then cleaning, still doesn't work. PLEASE HELP!!

... Vacuums

I have the Bissell Proheat (7901) It will pick up water and the hand tool works fine. I noticed that the red indicator stopped spinning. Then I noticed no water was coming out. If I put down water using the hand tool, the vacunme will pick it up. When I called Bissell they had me do something with the indicator. When it didn't work they said take it in for repair.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

NuTone CV750 Central Vacuum won't shut off. The on/off switch on side of unit has no effect. Did continuity test on switch, it tests ok. I've disconnected the low voltage wiring at the side of unit, that had no effect.

I will assume that you disconnected the switch from the circuit when you did the continuity test -- that is really important.\015\012If so, then i think that the relay inside the top of the unit is stuck on, or the low voltage wires (inside the ... Broan-NuTone CV750 Central Vacuum

My Kenmore progressive upright vacuum, model 11635923500 has a problem with the brush rotating. Sometimes the brush will not rotate until the unit in lowered way down, like the activate switch has rotated. Can I get inside the unit to check the switch, if so were do I look

... Kenmore Vacuums

My lux 7000 has a new bag but when i start to use it with the power unit or without the unit shut's it self off i can reset the lites or the motor if you will by clicking the on off switch 4or 5 times and i'm ready to go again untill you start to work and off it goes you can repeat the switch thing as long as u want, it just won't let u vacuum ,it turn's it self off .I blew it all out but found nothing in it. if u don't try to vacuum it will run as long as u want to listen to it. Can you

Have you replace the afterfilter? It may also cause this if rather dirty. It's located under the tool caddy/air diffuser on the back half of the machine.\015\012Try this: Disconnect hose, turn on vacuum. Does it continue running? If so, pl ... Electrolux Lux 7000 Bagged Canister Vacuum

Shark s3325 stopped working while steaming; thinking the unit had ran out of water I allowed unit to cool before refilling, however unit over flowed with only 700ml water added. When I plugged unit back into outlet it would not turn on (red light was not on) but I hear a click upon plugging in unit, when turning unit power button on and when turning on the handle switch. Please advise how to resolve this problem.

... Euro-Pro S3325 Handheld Steam Vacuum

I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the

Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums

Can't get water to spray out of the hand tool nozzle

When you attach the main suction hose to the front of the machine, you also have to connect the soultion hose to a valve located on the side of the machine. When the machine is running, take a small screwdriver and depress the centre of this valve. Y ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

My hose tools wont pick up. when hose tools unattached suction is fine and will **** my hand fiercely, but once tool attached no suction..... how am i gonna pick up cat hair from seats now?! its a dyson DC04 but it wouldnt let me choose that!

I have a DC04 and the hose tools are a open hole.The only reason they want pick up is they are blocked.If you say they are sucking your hand when not attached.Make sure the hose is not blocked by taking off the cover at the front.Allso check the cyli ... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

I am an athletic coach and use four Terrain 550 radios and assistants to help coach, moniter and time athletes at various distances away from me. I would like to be able to communicate with the athletes directly, both ways, but have not been able to find a suitable headset unit to use with these radios. Please can you arrange to supply or recommend some headset units compatable with these radios? Even better, units with mikes to enable the athletes to run relatively hands free. Many thanks f

You can try these links 1. http:// ... Vacuums

Altrev, I have an ODC325 Black&Decker spacemaker coffeemaker on my boat and it stopped working this weekend although the hot plate still gets hot. I suspect it is the thermal switch as you described (I hear a click when I switch the machine on but nothing happens and the heating element does not kick in). I would be very happy to receive one or two of these 14 spare switches you mention so I can repair the unit. If still available I would appreciate hearing from you how we can do the transact

We don't sell parts individually on the site here.... was it some other solution for another person you saw about the switch? I don't believe there really is a part called a thermal switch... there is a thermal fuse but if the hotplate gets hot I wo ... Vacuums

The mechanical off/on in the handle is not working with the electrical on/off switch upon removal of the handle you can cut the machine off by hand but after ensuring the the handle is re-placed in the proper position the machine will not turn off so what new handle or is the rocker switch has worn is now to hard for the mechanical switch to operated

Hi there it's SmartAlec from NelsonVacuums.com.au here. You are spot on in your diagnosis however i have fixed heaps of these and i have found no way to tell wether its the ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.5739 seconds