Having problems with your Bissell 1699 ProHeat Clear View Upright Steam Vacuum ?

MOD 1699-f reassemble cleaner fluid mix switch

\015 I had a problem that required me to take apart the unit. When I tried to reassemble it I can not get the fluid mix control valve to work. I don't know get it together.Can you help me?Thanks\015

Answers :

This is one of the most difficult machines to work on, but I can help you to reassemble the the "Automix Assembly." There is a black piston with an O ring on it that has to be put in place before the hood is put back on. This part will actually set inside the windings on the smart mix knob, before the hood is placed on the machine, and as you place it on the machine, the piston will have to slide down in the hole on the automix. Getting the piston into the windings can be a little tricky. You might have to play with it a bit and it doesn't lock into place. It just sits in there loosely, just enought to hold it in place while you put the unit back together. It's hard to describe how to place the piston in the windings of the knob, but I'll give it a try. Hold the hood upside down and place the squared corner of the piston into the squared corner of the hood between the knob and where the solution tank would sit on the opposite side. Now you can turn the know and screw the piston down into positon and the hood is ready to install.
\015\012Hit: put a book or peice of 2X4 under the unit between the rear wheels to lift the wheels off the work surface and help line everything up. If the hood doesn't feel like it is seating into place correctly, something is wrong. Very important on this machine: if even one hose is slightly out of place it with not pump. If it doesn't pump alway check the attachments to see if they pump. It they don't, then you might have a clogged heater.
\015\012
\015\012Good Luck
Repair Help & Product Troubleshooting for Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

MOD 1699-f reassemble cleaner fluid mix switch


This is one of the most difficult machines to work on, but I can help you to reassemble the the "Automix Assembly." There is a black piston with an O ring on it that has to be put in place before the hood is put back on. This part will actually set i ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch


... Hoover Vacuums

Steam Vac carpet cleaner Mod. fh50020. Its not sucking up the fluid. '


... Hoover Vacuums

Replace on/off switch on rainbow D3 vacuum - Rainbow D3 Canister Vacuum Cleaner Power Nozzle Reset Switch Vac Cleaner Power Nozzle Reset Switch


... Rainbow D3 Canister Vacuum Cleaner Power Nozzle Reset Switch Vac Cleaner Power Nozzle Reset Switch

I have bagless samsung air track 2000w tein cleaner vaccume cleaner..it has only one switch for on and off...cant find a switch to put the cord back????? .


... Vacuums

I have a bissel proheat and i can't figure out how to switch it from carpet cleaner to upholestery/stair cleaner. There's no button or switch that I can see and it doesn't kick in automatically.


On the most current model of the Pro heat 2X, there is a dial on the clear plastic section (located on top of the bladder section) and you can turn it from floor use to tool use. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The last time the vacuum cleaner was used the outlet sparked causing it to smoke when turning on vacuum cleaner. I replaced the outlet and plugged it in and things seemed o.k. Today I turned on the vacuum, it stayed on for a mili second and went off. I checked the switch on the vacuum and it showed voltage coming and going, but would not turn on again. I checked all the wires in the area of the switch all seemed o.k. I thought maybe there might be a short in the cord. When I went to plug


... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Smart Mix Dial - Reassemble Cover


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Kirby Vacuum Cleaner on/off switch won't stay switched on


If the motor turns on turns off in the course of the vacuuming, check the cord or the switch This is how you replace your cord on a Sentria vaxuum.\012 ... Kirby Vacuum Cleaner Switch For G3-Sentria 110590

Hi! My name is george and i forgot how to start my cleaner. I have a bissel proheat # 7901-1. Can U send a copy of the start-up directions after I fill the water mix tank up?


I forgot how to start my Bissell Pro Heat Upright Wet/Dry Please advise ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

The carpet cleaner does not spray cleaner, nor vaccum up excess water. It's been taken apart, cleaned, reassembled, refilled, twice. Have double checked seating of tank, placement of filled cleaner bottle and yes - it's plugged in.


Hi\015\012\015\012 \015\012\015\012The issue may be due to flow system; to troubleshoot the\015\012system follow the instructions--\015\012\015\0121. Remove Smart Mix piston from the main housing and place Smart\015\012M ... Bissell 1698-1 PowerSteamer ProHeat Plus Upright Vacuum

Mrs Cleaner flex has pulled out how do I replace Electric supply wire to switch on handle has broken at switch. How do you remove switch to repair? tonysimmons


Hi\015\012\015\012\015\012\015\012\015\012\015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I got this sewing machine , can anyone tell me what this control box is used for ?. It is mounted under the table in front of the motor,It says Control Box on the front and two push button number settings with can be adjusted up or down from ( 0 to 9 ) ,Next to these settings are two toggle switches. One is marked start with on and off and the other switch is marked end with on and off. Above these switches it it says Back Track . The tag on the box says ( Type LE -BB -24 - 110 - 220, 2


Still struggling with your model number. I understand from the added comment this is a Brother sewing machine. I was hoping to find a manual that would be of assistance. Here is a couple of websites that lists available manuals for Brother sewing ... Vacuums

I press the on/off switch on the Dyson DC05 and the vauum cleaner switches on unfortunately when I stop pressing it it switches off again. Please advise how I would need to repair this. Many thanks. Regards Michael Segal


If you can make it work by holding the switch down then it must be the switch or a bad connection on it. The only way to find out is unplug the machine from the mains and remove the switch to check it. A replacement should be cheap enough.pete ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I have a Bissell ProHeat 2x, and I did something dum. I had some powdered cleaner that said it works with carpet cleaners-well I mixed it in-and the next time I tried to use it, nothing came out. So, I took it part to check what was wrong-and found out that the powdered cleaner solidified in places. I cleared the nozzels, nothing. I think the solenoid, between the heater and nozzels is pluggd, and possibly the heater. I've got a question-could I use CLR to clean the heater, with replacing t


Heck yeah, give it a shot. Try running some water through it too- fill it up, heat it just to where it's hot and unplug it, shake it around and dump it out. Repeat. You might have to get a wire or something to go through and get the powder loosened b ... Bissell Vacuums

Bissell - Model 1697 - Powersteamer Pro - Carpet Cleaner I took the unit apart to replace some broken pieces and I can not seat the bottom to the top without properly engaging the soap/water mixer. What is the proper assembly procedure. What is the orientation of the water/soap mix valve when I seat the top to the bottom? The soap/water mix valve needs to engage the knob screw threads but this assembly is a blind operation. Do I turn to the soap/water mix knob to water only then seat the


Hi,\015\012http://dl.owneriq.net/7/7e477b7e-4440-49cf-a219-b68d301549e3.pdf\015\012This diagram will help you see the diagram plus the part assembly no and place it accordingly.I have also given link for Bissell - Model ... Vacuums

The switch on our Hoover Windtunnel vacuum cleaner is not working. I have located the replacement part on your website...part#Ho-28161067, I've removed the wires from the switch. Is there any trick to actually removing and replacing the switch itself? It seems to be in there rather tight.


No, follow the directions to replacing the switch and you should be good. if you got the kit then splice the wires and replace them with the wires profied and the wire nuts, you should be good. ... Vacuums

Have a bissell pro steam cleaner the suction is great but the water leaks out the bottom I think it should spray from the front and the soap cleaner won't dispense from the bottle so I have to mix the soap cleaner in with the water Any solutions


Use this guide!\015\012http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope


Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums

I have a Miele S5980 vacuum cleaner, and recently had to change the Hepa filter. After doing the change, I tried resetting the reset button to switch off the Hepa filter indication light and it would not switch off. After a few tries, I accidentally depressed the switch, and it has dislodged from its cradle. Help, what can I do to fix this?


... Miele Vacuums

Can not get the Smartmix rotary switch to line up


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Power Switch How do I get the power switch out to replace it? I have a D4C model. Rainbow/Rexair. Is there a place where I can get a parts breakdown of the vacuum cleaner? Steve


This is not that hard:1. - remove gasket (it is glued so you may end up damaging it)2. - remove 4 screws holding baffle 3. - under it yo ... Rainbow E series Canister Wet/Dry Vacuum

Hoover F6212-900 My dear wife thought our 2 year old steam cleaner was a vaccum cleaner and used it with no fluid, I used it yesterday, it didn,t seem to clean the carpet and no water went into the dirty water tank it stayed dry. motor sounded ok Am I in big trouble Thanks for any help you can offer P.S. I still love her Alan from Canada


Press the handle release kick-button with your foot, extend the handle all of the way back, and take a look at the gap between the base of the unit and the handle/reseviour assembly. You should see several black hoses attached to the base and running ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

110-220V Dear Sir, I purchased a kirby sentria vacuum cleaner from ebau two weeks ago. I currently resid in the UAE with 220V power. My maid has plugged the vacuum to work with it unaware of the voltage difference, a terrble noise as mentioned came from the cleaner as well as a smell. She unlugged it and stopped t from operating. Can you please let me know how can i assess the damage? If this model has a switch from 110 to 220V IS there a solution with transfromer or motor to make it work? Thank


You may have burnt up the motor field when it was plugged into a 220V power source. But there are drop down transformers you can get to reduce the voltage form 210 to 110. AS Radio Shack or similar store would have them. ... Kirby G4 Bagged Upright Vacuum

Dear Sir: I just purchased a Bissell Rug Shampooer at a garage sale. The only thing I find for a model is on the back and it says Model 1695 there. Nothing on front. It is Navy blue and has a grey tank on it with a smaller one inserted at bottom of the large tank. It has two switches on the back of it and the trigger switch at the handle. The cleaner works, BUT, it does not extract any water back into the tank that is to pick up the dirty water. Could you suggest what I may look at t


... Bissell Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0513 seconds