Having problems with your Bissell 1715-G Spotlifter Bagless Handheld Vacuum ?

Need Bissel 1715 wiring schematic. Charging circuit has burnt resistor. Need to know resistor details.


Answers :

Can not believe NO ONE could answer this.
\015\012
\015\012The R1 resistor basically drops the 9V to around 5V for charging the battery pack. The resistor is a 10 ohm , 2 watt resistor. The other resistor is 220 ohm. This only limits the current to the LED.
\015\012
\015\012The 10 ohm resistor burnt because the battery pack was left to sit too long without use and charging. So the cells shorted causing excessive current through the resistor when you attempted to charge the batteries.
\015\012
\015\012After replacing the resistor, you will need to replace the battery pack before charging. Otherwise, you'll just burn the resistor again.
Repair Help & Product Troubleshooting for Bissell 1715-G Spotlifter Bagless Handheld Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need Bissel 1715 wiring schematic. Charging circuit has burnt resistor. Need to know resistor details.


Can not believe NO ONE could answer this. \015\012\015\012The R1 resistor basically drops the 9V to around 5V for charging the battery pack. The resistor is a 10 ohm , 2 watt resistor. The other resistor is 220 ohm. This only limits the c ... Bissell 1715-G Spotlifter Bagless Handheld Vacuum

Need Bissel 1719 series, 1718 series wiring schematic. Charging circuit has burnt resistor. Need to know resistor details


... Vacuums

Hi, my circuit board resistors are burnt due to my re-wiring the resistor switch. How do I fix this - S3755 wiring diagram?? need to know the correct resistors or get a new board


The only way is to get a replacement board. even the dealers are not provided with that level of wiring diagrams. ... Hoover S3755 WindTunnel Bagless Canister Vacuum

The battery will not charge in the sweeper. I can remove the battery and wire it to the power supply for charging and it will charge up and run the sweeper. So the power supply and the battery are both good. Obviously there is a circuit failure in the on board charging control. Anyone know a fix or a likely faulty component? I had a shark handheld about 8 years ago and it developed the same problem. I examined the little circuit board inside but saw no visible indications that would isolate t


... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

I have a Eureka Central Vac CV1601b. The motor does not stop unless the Unit is unplug from the electrical outlet. Any Idea?.I removed the control unit to check if there was disconnected wires or burnt wires. Everything look normal. The circuit board does not show area that overheated. There seem to be 2 relays. Likely one of the two went bad. What do you think.


If the unit is relay controlled, there is always the possibility that when the unit was turned on, the relay contacts welded themselves shut making the power button ineffective. \015\012\015\012If you're familiar with relay pinouts, with ... Vacuums

Bissel Proheat 2x circuit board


Use this link: http://www.4cleanerfloors.co.uk/cgi-bin/product.pl?PID=1278118_amp;brand=Bissell_amp;model=_ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I need instructions on how to use the Bissell PowerSteamer Carpet Cleaner. I borrowed it from a friend, but I don't know how much shampoo to use or other details.


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Hi I have the Ambassador 337 model. I had to rewire the on off wiring due to the "N" wire rubbing through & breaking. I have it all together again although a piece of wire in the shape of a "V", with a bend each side of it has dropped out & I don't know where it came from!!!! Please send me diagram of this model so that I know where it goes. Cheers Ian.


... Electrolux Vacuums

I have a dyson animal dc17 vacuum and it totally died. Now I can't figure out which wires go where when I install my new motor. (motor #: 160906G) Do you happen to know where the various color wires go or a place I can see a diagram of the motor with wires attached? I should have taken a photo of it before tearing out the old motor. I don't know where to connect the three coming out from the upright portion of the machine and the red seems to go to a switch (?) and there is a black (connected t


... Vacuums

Burnt out resistor


I'm in the same fix. I learnt that a new pcb is \302\24368 so had the pcb repaired but after the machine has warmed up it now cuts in and out. Like you, I haven't been able to locate a wiring diagram so am trying a last minute lash-up before binning ... Miele S251i Plus Bagged Canister Vacuum

Trying to wire aa Nutone model 763RL bath exhaust fan/light. The conduit coming from the breaker box has a red wire, a black wire, a white wire and a ground. The fan has two white wires, one black wire, one blue wire and one green wire. I have wired the whites together, but do not know how to wire the blance.


... Vacuums

I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks


... Bissell 3750 Lift Off Bagless Upright Vacuum

Bissell powersteamer i have a bissell powersteamer my aunt gave me, but do not know how to operate it to put the water and cleaning solution in it. please let me know how to operate. or how can i get the operation guide or manual


BISSELL User's Guides can be downloaded at www.bissell.com\012On the front page under Customer Service click on User's Guides and enter the model number of your unit.\012User Guide will be displayed as a PDF file. ... Bissell 8806 Powersteamer Upright Vacuum

I took the motor out of my bissell model 82h1 and cant remember where to hook up the wires.


You should contact one of BISSELL's Authorized Service Centers for assistance. Here's a link to locating one.\015\012 http://www.bissell.c ... Bissell 82H1 Cleanview Helix Bagless Upright Vacuum

My Oregon Scientific BAR888 has 5 windows, 1. temperature, 2. humidity, 3. mb/hPa or inHg (switch at the back), 4. bars showing pressure changes over 24 hours, and 5. time/date. Window 3 gives an option to set something between 0 and 2500. Oregon say they only have one set of instructions for the BAR888 but they do not match my instrument as there is nothing included for my window 3. Trouble is I don't know what the 0 to 2500 relates to and therefore don't know what to set it at.(My model does n


... Vacuums

Wireing schematic for Bissell vacuume cleaner#3760-4


... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Wiring diagram took wires off motor and do not know which goes where.There are two main from plug in one whit one black then two of same coming from light in front.On the motor ther are more terminals than wires.On diagonal corners there are black dots.Can you please help this cost 800$ and do not want to burn the motor due to crossing pos and neg.Do you have a picture or know where I can find?


... Oreck XL21 Bagged Upright Vacuum

I have an antique 8 arm chandlier and want to put it up in my bedroom but the wire hasnt any differance in color, how do i wire it to the exsisting wire from the celing , what wire goes to what wire ? I wont be installing it myself but would like to know so i dont sound so silly


Starting with the proper wire gauge, always white to white and black to black. ... Vacuums

I have an old Friedland door chime (approx 30 years old). It has 5 terminal screws to connect wires. They are labeled 0-4. I removed the chime during remodeling and would really like to reuse it. I did not label the wires and where they connect when I removed it. I can't figure out how to wire it. I contacted Friedman and they were of no help... didn't have information on chimes that old. Can you help with how to wire the chime given it has five connections screws with no labels other t


... Vacuums

Wires on a bissell steam cleaner


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Confusion and embarrasement have caused me to appeal for expert advice. I need to add a second flourescent light fitting in the loft. I recently added one from the existing wiring circuit via junction box and pull chord switch and it works fine. I have wired in the second light and now neither of them work. I have replaced the starter (as I had a faulty one in the first light. But i annot get them to work. I have installed a second junction box for the second light and wired all like terminals


... Vacuums

I have a Janome Model 556, purchased in 1968 in Zimbabwe. I need to know how to replace the wires of the foot pedal. There were 4 wires used to go into the small plug attached to the machine, however the wall plug only had 3 wires.


... Vacuums

The Lifesaver smoke alarm model 1225 is hard wired, no battery and is chirping. I have it pulled out with wires coming out of the back, but can't open the front face to get in to disconnect the wire. Anyone know how to open it up?


Hi, you should be able to grasp it and twist it to open/remove it from the juntion box to expose the 120 volt wires. They do not open like one with a battery type, so twist it I believe CCW to remove it from the box to disconnect the wires. Please be ... Vacuums

Wiring the switch for a kenmore vacuum cleaner I need to know where teh different colored wires go. It had a short in it so I replaced the plug but think I wired it incorrectly. Its a Whispertone 300 model 116.28612790 The canister works but the beater bar doesn't.( it worked before a rewired the switch. Thanks


... Kenmore 23313 Whispertone Bagged Canister Vacuum

My Dyson DC 24's beater bar switch didn't actuate and the beater bar didn't turn. When I brought it to a certified serviceman he told me that a wire interferred with the switch and all he had to do was move the wire out of the way of the switch. At the time the machine was under warrantee and it didn't cost me anything. Now however, the machine is out of warrantee and the problem has returned. Does anyone know how to access the switch and move the wire out of the way?


Hi- I had the same experience but it turns out there's a small trip switch if you've taken the brush out to clean it, it needs to be reactivated by pressing the small red button to the right of the brush... took me a year to figure this out! Been mea ... Dyson Ball DC24 Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 1.0438 seconds