Having problems with your Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum ?

I CANT GET MY BISSELL SPOTLIFTER MODEL 1716 TO SPRAY THE SOLUTION.


Answers :

\015\012

1) Make sure there is water in the solution tank.
\015\012

2) Try priming the machine by instructing the consumer to squeeze the trigger
\015\012

repeatedly for 1 to 2 full minutes. Important: If you cannot
\015\012

squeeze the trigger all the way in, remove the tank from the back of the
\015\012

machine and then try squeezing the trigger with the tank removed. There is an
\015\012

internal valve that could be sticking. By removing the solution tank and squeezing
\015\012

the trigger, it should break it loose, allowing the trigger to be fully depressed.
\015\012

3) Make sure the open end of the siphon tube in the solution tank is not pushed into the
\015\012

side of the tank, covering the end of tube. If it is, push the bend in the
\015\012

Siphon tube toward the back of the solution tank.
\015\012

4) Check to see if the siphon tube has become disconnected from the outlet fitting on
\015\012

the inside of the solution tank. If so, you need to buy a replacement solution tank. Parts
\015\012

can be found at www.bissell.com
\015\012

5) Check to see if air comes through the spray tip by repeatedly squeezing the trigger
\015\012

with solution tank off the unit. If not, spray tip may be clogged. Try and unclog
\015\012

spray tip with a pin or paper clip.
\015\012

If still no spray, please check the following:
\015\012

a) Make sure the solution tank is installed properly.
\015\012

b) Check to see if black O-ring is present on rear connector to solution tank.

Repair Help & Product Troubleshooting for Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I CANT GET MY BISSELL SPOTLIFTER MODEL 1716 TO SPRAY THE SOLUTION.


\015\0121) Make sure there is water in the solution tank.\015\0122) Try priming the machine by instructing the consumer to squeeze the trigger\015\012repeatedly for 1 to 2 full minutes. Important: If you cann ... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

Bissell Proheat Plus Model 7901-P won't spray out cleaning solution, but does **** up liquids. What would cause this? Also, Lost Manual where can I get another?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I cant get my bissel proheat pet to spray water have replaced pump and cleaned heater sprays a little then stops any ideas?


You may want to contact a BISSELL Authorized Service Center to have a qualified technician inspect your machine.\015\012Here's a quick link to locating one. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell proheat 2x model 8920 water is not spraying out just getting a little trickle. Model is less than a year old


... Vacuums

Model#F5858-910 hoover steam vac,silver ,spin and scrub. It doesnt seem to spray cleaner it seems to stream it now. what could be wrong? I cant get to end of where it sprays to see if something is blocking it . otherwise it works great. I have it about 8 yrs. always worked good until recently


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Manual issues Have reciently purchased a kirby from ebay (gotta love ebay) but has no manual. I believe the model is a heritage (cant see a II though) Do they all have roughly the same manuals??? I have all the attactments - spray painter, hair trimmer, turbo brush etc but really want to get the most from the machine. Where do I get manuals for machines that are 20yo???!!!


Many years ago I was a service engineer for these machines in England they were actually made by a company called Scott &Fetzer in the USA and Branded KIRBY or CIMEX.\015\012\015\012See if Scott &Fetzer are still around and ask th ... Kirby Heritage II Vacuum

My Bissell proheat 2x model 9200 is not dispensing cleaning solution. I hold the trigger and the carpet doesnt get wet at all. i poured water on the carpet and it sucks it up. the cleaning solution does mix with the water but it not being dispensed on the floor.


Hi, \015\012when last did you service the machine?\015\012\015\012i believe should service the machine.\015\012try to open the machine.\015\012\015\012when opening make sure you notice where the part you are remov ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissel shampooer I have a bissell shampooer powersteamer power brush model 1694-W. I cant get it to dispense water onto the carpet anymore. I think it's because I let my 3 year old ride on it while I was shampooing. I assume I have depressed some special little part that is now broken or mashed or something. Stupid I know....


Yes there is a belt on the side that will need to be changed ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I own a Bissell Proheat Pet Model 8910. After just a few uses and changing both the brush and pump belts (trying to resolve problem) carpet doesn't get wet any longer. Carpet solution comes out normally but the water barly leaves the section of the tank I fill water into, resulting in carpet recieving to much solution and not enough water. Any advice?


... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate


Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like i ... Vacuums

My Bissell ProHeat 2X Model 8920 will not spray the cleaning solution. It has suction but nothing else. What could I try to fix it?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell Proheat Turbo 2x model 9300. It has stopped spraying at the floor. The hand tools will work so I assume this means the problem is at the base somewhere. I cleaned the nozzles but don't know what to try next. It has always had a problem with dumping too much cleaning solution as well, don't know if this is a contributing factor


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have Model 9400-3 Bissell Pro heat select 2X microban. I cannot get the solution to come out to shampoo the carbet. I cannot find my instructions that came with the shapooer. Please help.


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Cant get my bissell powersteamer #1685 to dispence the water/ cleaning solution and have lost the opperators manual


That means that the pump belt is worn or broken. You can get a replacement and view the manual here:Bissell PowerSteamer Belt and Man ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Bissell model 8920 deep cleaner. I get cleaning fluid spray on the upper furniture wand but not at floor wand.


The heater is clogged its in the handle ... Vacuums

My Bissell Model 9200 quit sucking up sprayed solution.


There are a couple areas to check:\015\0121. The black gasket where clearview water collecting unit and the base's front meet. Ensure gasket is in good condition.\015\0122. Check if you're getting sufficient suction: remove the water co ... Bissell 9200 Upright Vacuum

I have a bissell pro heat carpet shampooer model # 8910 and it will not spray any solution out what could the problem be its only been used twice without any problems


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.B ... Bissell 8910 ProHeat Clear View Upright Vacuum

My Bissell carpet cleaner model #1697-W will not dispense the cleaning solution and will not **** the water back up--also need to know how you get to the belt on the machine?


The drive belt for the pump is located under a cover on the front right side as you look for the front of the machine. Just lift it up and the belt will be obvious. If it is not sucking then make sure that the dirty water tank is empty and that ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I have a Bissell Pro Dry steamer and cant find my manual. I filled the bottom tank with water and solution and it is pouring out. I havent used the cleaner in quite some time so I can't remember how it all works. Where can i get a manual?


User’s Guides can be downloaded at www.bissell.com\015\012On the front page under Customer Service click on User’s Guides and enter the model number of your unit.\015\012User Guide will be displayed as a PDF file. ... Bissell Vacuums

My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.


... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

I have a bissel powersteamer and it quit spraying the solution on to the carpet... the jets are not blocked....how can i get it working again?


Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Vacuums

Can't get it to spray the cleaning solution - Bissell 8910 ProHeat Clear View Upright Vacuum


... Bissell 8910 ProHeat Clear View Upright Vacuum

We think our Bissel Pro Heat Pet is a piece of junk. It will not spray cleaning solution.


Here's a link to troubleshooting steps to assist you. http://www.bissell.com/FAQDetail.aspx?id=1122&cid=ccsocial\015\012If yo ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My bissell sprays solution and water but does not **** it back up. After the water and solution are gone the return tank is completely empty


1) check the tank is full of water2)check gasket position,can be worn, or damaged fix it3)check the belt worn for inoperable brushes.4)check motor duct gasket, and test it. yif you notice suction in the duct, remove the tank, for assure i ... Vacuums

I have a Bissel 9300-C 0714 BC Carpet Shampooer. It was working great and all of a sudden it stopped working. It still sucks up dirty water but it does not spray water onto the carpet. I can get it to spray water through the smallest hand attatchment but not through the large hand held piece on the base of the machine. I really hope you can help me, I am a dog groomer and I really need my machine to work properly. I can get it to spray water out of the smallest hand attatchment but that's all t


The spray jet has become clogged from the soap.... just clean it out. same thing happened to my attachment. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1195 seconds