Having problems with your Bissell 1720-1 Little Green Wet/Dry Vacuum ?

Our Bissell 1720-J has just died on us. It is making no attempt to pump liquid in or out and gives every impression of being dead. The fuse is OK, but putting an Avo across the Live/Neutral pins shows no circuit at a 2000K ohm level, even when the switch is in the "1" position. Any thoughts?

Answers :

Repair Help & Product Troubleshooting for Bissell 1720-1 Little Green Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our Bissell 1720-J has just died on us. It is making no attempt to pump liquid in or out and gives every impression of being dead. The fuse is OK, but putting an Avo across the Live/Neutral pins shows no circuit at a 2000K ohm level, even when the switch is in the "1" position. Any thoughts?

... Bissell 1720-1 Little Green Wet/Dry Vacuum

I have a grafter safe model no AA/R06/1.5V - GT24 batch number 0171-2C and have lost the instructions and the key. I have put in a wrong pin number and now I am getting the message 'error' flashing across the safe and don't know how to get into the sate.

... Vacuums

It's been awhile since I have used my shampoo system on my Ultimate G series Kirby. Well, as instructed I took it apart and cleaned it. Now I can?t figure out where to put the ?screen cap? and ?sponge filter?. I have my manual in front of me and the only place it shows the filter and sponge (page 35 in the manual) is when it?s been taken apart to clean. It doesn?t show where to put it back. I don?t know what I would do without all the pictures in the Kirby manual. HELP! Thanx. Visual Kirby Vacuu

Hello,\015\012The littlew round screen goes in the hole where the hose attaches to the tank. The round foam filter goes up in the hole underneath the on/off valve for the foam. Here is a guide if you need any more help...\015\012\01 ... Kirby G6 Bagged Upright Vacuum

No suction Hello - any help with this would be much appreciated! I just changed the bag and filters. The machine runs, seems normal, but there is no suction. There is no blockage of the hose, as indicated by the fact that that little viewer window above where the hose connects to the unit is not showing the red portion that it shows when there is something blocking the hose (god, this is hard to describe!). If I disconnect the hose and put my hand over the hole, I feel some suction. But

Well, it actually sounds like there is a blockage. Try removing your hose and dropping something through it, like a quqrter. If it comes through, no clog. If it is clogged, I believe that machine has a blower on the upper part of the cleaner (mayb ... Miele S514 Solaris Electro Plus Vacuum

How to put click pin back in craftsman snowblower

Open pin, Separate pin from circle. Insert pin into hole of drive wheel, the close circle unto pin. ... Craftsman 155443 Click Pin

Can you show how to put the pet turbo brush back together?

... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

I am trying to install a train air horn. i bought a viair compressor for it. the horns themselves have a 12 volt hookup going to what i believe is acting like a solenoid. when charged, you complete the circuit and walah, the horn blasts. the problem im having is when the compressor is building pressure, the air horn is automatically putting out a dull sound, getting louder as the pressure gets more and more. it sounds like its out of one horn however. it is doing that without the 12 v hookup. is

Hi! just a tip regarding the sound that comes up when building pressure. Is there a gasket or rubber seal on the horn? You may need to replace this for it may be worn. The air may be coming out of the worn seals resulting to sound even when not trigg ... Vacuums

String caught caused vacuum to stop. I tried taking the battery out and putting it back in, but now the light doesn't go on showing that it is charging. I don't see anything caught in the brushes.

... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

Impeller installation i took the whole vacuum cleaner apart to replace the impeller . i did not take note of the way the bushings need to be put on the shaft . do you know of a diagram out there that shows how to do this.

Here is my online guide to changing the fan. Hope it helps...\015\012\015\012http://reviews.e ... Kirby G4 Bagged Upright Vacuum

My boyfriend took the vacuum apart now he cant remember how to put it back together do u have a picture so i can show him?

Uh all i can say is good luck with that. a pic probably would not help they are very complicated machines to work on. if i were you i would put everything in a box and take it down to your local vacuum repair shop and have them do it it will still b ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o

Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I posted my problem earlier today that I was having with my Bissell Little Green Machine not dispensing solution, but sucked up no problem. Someone said that the most common problem was a blockage. We put hot water in the reservoir for 15 minutes as advised and it still will not dispense. The fluid is now ''dribbling''so it is better. It is just not spraying. We are able to blow from the end and make bubbles in the reservoir which shows us it is not blocked. Any other suggestions?

Okay. I fixed this on mine. Undo the screws on the handle, right by the trigger. You pull the tubes off the little valve. Push on the button and see if you can blow through the valve. If not, push a pin around in the valve (with it pushed into the ... Bissell 1720-1 Little Green Wet/Dry Vacuum

I have a Eureka Central Vac CV1601b. The motor does not stop unless the Unit is unplug from the electrical outlet. Any Idea?.I removed the control unit to check if there was disconnected wires or burnt wires. Everything look normal. The circuit board does not show area that overheated. There seem to be 2 relays. Likely one of the two went bad. What do you think.

If the unit is relay controlled, there is always the possibility that when the unit was turned on, the relay contacts welded themselves shut making the power button ineffective. \015\012\015\012If you're familiar with relay pinouts, with ... Vacuums

My Kenmore 116.25812508 power nozzle motor will not run unless I tilt the handle. I checked the connectivity from the circuit board in the power nozzle base to the telescoping wand with an ohm meter and there is no indication of disconnect.

I have had this vacuum for about 3 yrs and nothing but issues with it. It's been in the shop already once and it needs to go again. No power in the power head. A wheel came off of the powerhead too .. keep snapping it back on but it always comes off. ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a

You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

Need a manual to show me how to put on a belt. None of the pic

... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

I took my vacuum cleaner apart to clean it because it was clogged inside and now I am having trouble putting it back together. I am looking for a manual of some kind to show me how to assemble it. It is a Kenmore Progressive Model # 11636933502

... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?

Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

Red "bag is full" indicator shows even though new bag has been put in and vacuum cleaner wont pick up. Also floor adjustment does not adjust. This is for a powerforce model 3522 series

The red light tell you that it is sensing a full bag. But a clog in the hose or the inlet down by the brush roll will also do this. ... Vacuums

Roomba 560 is just over 1 year old and has worked well. Now it only moves 20 - 30 cm from point where it is put down and does not move across the room. I have cleaned the front wheel, and cliff sensors and have rest the software to default but no improvement. Suggestions please?

ARe you waiting for the error codes?\015\012There appears to be a problem with the bump sensors and they usually are going bad. Here is a site for the problem:\015\012 ... iRobot Roomba 560 Robotic Vacuum

Hello, On the 24 of June 2010 I purchased an Oregon Scientific Solar weather Station with indoor humidity gadget in Budapest Hungary. I opened it and tried to put it in function only 10 days ago,at the end of November,because I had another one(not exactly the same),which I had had for several years and I wanted to change. I live in Israel. After I read the instructions I did everything I had read,but the outdoor temperature doesn't show off and the clock isn't correct either. What should

I'm a little confused about this question. You bought it in Budapest but live in Israel? This could be why the clock is wrong. Many of these Weather Stations (it would be helpful to know the model number) have radio controlled clocks, which pick up a ... Vacuums

Vacuum cleaner We have a panasonic MC-E47electronic which seems dead. It has a speed control which we nearly always had on full anyway. Have tested continuity through plug, flex and on/off switch and all OK. from then is open circuit through speed control which consist of slide rheostat and mystery small green box (2cm x 2cm x 1cm approx). Across motor there is negligable resistance. Machine is quite old and not worth paying out loads on poarts if it is safe to bypass speed control and connect

Yes it is safe, but i would make a switch? ... Vacuums

For the first time, I tried using my Kirby Sentria shampoo attachment. I've lost the manual but found instructions online for making the swap from regular vac to shampoo-er and got it all assembled. The foam laid down just fine, however, when I run the vac back over the foam to pick it up, there is not a stitch of water showing up in the tray. First I thought maybe it was bc I hadn't put that much of the foam/water onto the carpet, but 12 hours later, the carpet is still wet in spots. Clearly

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=638285\015\012Generic problem for all Vacuums\015\012For the first time, I\015\012Posted by MHicks on J ... Vacuums

When removing the canister bag, the plate and spring that it slides into popped out. When I put them back in, the bag full indicator is completely red. It is a new bag and filters. I think I am not getting the plate and spring back in the canister correctly. Any instructions or pictures showing proper insertion and configuration of these? I looked in the manual and the part is only shown while bag being inserted.

... Miele S514 Solaris Bagged Canister Vacuum

Wher can i put cleaning pin - Sienna Aqua Laser Steam Mop

... Sienna Aqua Laser Steam Mop
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0518 seconds