Having problems with your Bissell 3102-0 EasyVac Upright Vacuum ?

My bissell easy vac won't pick up after first use

\015 I jsut bough the easy vac and it worked beautifully. I noticed the hose was clogged so I cleaned it and the canister. The vacuum is STILL not picking up and I've only used it once. HELP!\015

Answers :

Well after reading and re-reading my bissell easy vac manual (I had only used the vac twice), I went through all the troubleshooting recommendations. I cleaned out all filters and even though I had only used my hose attachment once, I was shocked that it was completely clogged! I took the whole thing apart and thoroughly cleaned it out according to the manufacturers instructions. It is working beautifully again now, I just take extra care to check it after every use...it can be a hassle, but I find that's what happens when you buy bargain items; you spend less but end up investing more time in upkeep. I hope this helps!! :)
Repair Help & Product Troubleshooting for Bissell 3102-0 EasyVac Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

For the first time, I tried using my Kirby Sentria shampoo attachment. I've lost the manual but found instructions online for making the swap from regular vac to shampoo-er and got it all assembled. The foam laid down just fine, however, when I run the vac back over the foam to pick it up, there is not a stitch of water showing up in the tray. First I thought maybe it was bc I hadn't put that much of the foam/water onto the carpet, but 12 hours later, the carpet is still wet in spots. Clearly


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=638285\015\012Generic problem for all Vacuums\015\012For the first time, I\015\012Posted by MHicks on J ... Vacuums

My bissell easy vac won't pick up after first use


Well after reading and re-reading my bissell easy vac manual (I had only used the vac twice), I went through all the troubleshooting recommendations. I cleaned out all filters and even though I had only used my hose attachment once, I was shocked th ... Bissell 3102-0 EasyVac Upright Vacuum

Bought a shop vac about 3-4 mos ago and while i was using it, it cut off and wont cut back on. This is the second shop vac that done this and I took the first one back and got this one and it did the same thing. It is a 12 gal. 4.5 peak hp.


... Shop Vac 401-12-00 Wet/Dry Vacuum

I have a Hoover linx cordless stick vac. I have not had it but several months and it has quit sucking anything up. It worked great when I first got it. I was so excited at how well it worked. It had gotten hair wrapped around the brushes but I got that out and thought it would work better. It is turning and sounds like it is working but it does not pick it up. I could use your help please. Keely


... Hoover Platinum LiNX Cordless Stick Vacuum

Wont pick up dirt it will only pick up when i use the hose if i use the upright it dont pick anything up and dust flys out so whats up


... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......


Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

First use, motor died (Ridgid SmartCart shop vac WD7000)


... Vacuums

I do not have my users manual and have never vacuumed wet with this vacuum. How do I change it from a dry to wet vacuum. Can't find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what lost my user manual never used it to pick up water. need to know how to puit it in wet mode i want to clean the dirty water out of my pool.


\015\012Vacuuming Liquids\015\0121. When picking up small amounts of liquid\015\012the filter may be left in place.\015\0122. When picking up large amounts of liquid\015\012we recommend that the filter be\015\012r ... Craftsman 17765 Canister Wet/Dry Vacuum

We just took our dirt devil Platinum Force Carpet Shampooer Model CE7900 out of the box - first time used. It puts soap and water down fine, but we can't get any dirty water picked up. None of the trouble shooting suggestions in the manual apply. HELP! (We had only the power on when trying to pick up the dirty water.)


... Dirt Devil Easy Steamer Upright Wet/Dry Vacuum

Hoover steamscrubber I loaned my vac to my daughter who used it to clean shag carpet with lots of dog hair......now the scrubbers wont spin I have taken them (scrubbers) out and cleaned the vac....don't know where the lint trap is...but i DON'T see any part moving that would make the spinners rotate either Thnks...Lydia


I had the same problem. Fixed it by taking the machine apart and lubricating the bearing inside the turo tunnell. It's a pain, but not impossible if I could do you can. You must start by taking off the cover. Don't forget the scvrews on the front by ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I just bought a shop vac to **** up the winter slop in the garage. the first time I used it, it worked perfectly but the 2nd and 3rd times I used it, it spits water from the exhaust. Why? It doesn't seem to have a plug/clog and I have the foam sleeve plus the circular paper filter on it, as per directions. Help!


Too much water in the unit causes what you describe. Water should be drained and the unit completely dried between water events, or unit will rust and have shortened life. ... Shop Vac 925-13 Canister Wet/Dry Vacuum

No suction i have a hoover supreme wind tunnel vac and its relatively new and the suction, well......sucks. It wont pick anything up! I am extremely frustrated! I picked up a ball of fuzz off the carpet and held it under the vacuum and it still wouldn't **** it up. I then shoved the fuzz up INTO the vacuum. It fell right back out. I may as well not even vacuum. Please help!


I have found more vacuums on the way to the dump because they were full. Check. Is it full?\015\012If not the air way is clogged. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I'm using a steam vac for the first time, i wanted to know if the bottom piece that you empty out the dirty water has to have water in to use it. or is it suppose to be empty?it's an upright hoover steamvac for heavy traffic areas and spot cleaning


Hello,\012The bottom piece should be empty when you use your machine. Make sure you rinse it our real good when you are finished.I hope this helps. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My dyson dc25 just turned off while i was using it first the roller brush stoped turning so i used the hose and now it turned off and wont turn on how do i fix it?


... Dyson DC25 All Floors Bagless Upright Vacuum

My vacuum used to work great but now it wont pick up anything


You must look for a clog in the hoses and where the hose goes into the unit ... Vacuums

Karcher steamer vac wont steam, its only been used a few times


... Karcher DE4002 Steam Vacuum

Vac wont pull/**** anything while we try to vac floor,


Hello RonD30,\015\012If you are getting suction thru the hose and not from the bottom section.. you have a clog somewhere inline with the base area... If you have access to a shop vac ... unplug the Hoover, open up the base and remove the beate ... Hoover Vacuums

I was replacing the belt on my Eureka Smartvac 4870 and one of the felt gaskets (or part of it) popped out. I thought I put it in correctly, but the first I used it after replacing the belt, the gasket got mangled by the brush. I'm wondering how important it is to get fixed; is it a part I can pick up anywhere and fix myself? Thanks for the help.


I'm no expert but if you mean the felt on the roller, you have to replace the roller (expensive,esp. for such a minor part). So. I found some felt with adhesive in the craft section at Wal-Mart, trimmed it to fit and done deal. Felt reduces friction. ... Eureka Smartvac 4870 Bagged Upright Vacuum

What if i use my wet dry vac to pick up water without a filter


DO NOT USE A FILTER WHEN PICKING UP WATER!!!!!\015\012\015\012Im certain if you check the instruction manual it says to remove the filter. ... Shop Vac 925-13 Canister Wet/Dry Vacuum

We have two of these vacuums and both of them have experienced the same problems. First the floor heighth adjustment doesn't work and now neither one will pick up on either carpet or floor when in the brush/floor mode. They both seem to work with the suction hose function. We have removed the back panel to see if there was an obstruction but it was clear. We have changed the bag and the small filter (not the HEPA filter) all to no avail. What else can we do? We are desperate to use our vacu


Did you check the powerhead for obstructions? With a bend in the tube just below where the hose connects, this is a common spot for clogs. To check, detach hose and drop a coin in the hole. If it doesn't drop through, a blockage is present. Use t ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

Hoover steam vac smelled like melted wax while using heard a pop now wont turn on


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

How do I get a Stanley Wet /dry vac 8 US gallon on after 2yrs. of use and now it wont turn on ?'t turn


... Vacuums

My shark cordless vac 15.6V model # 5V7OZ does not pick up the dirt, I very seldom use it so what is the problem???????


Either one of two things can be wrong. 1st and most common problem is the filter is clogged up, or too much dirt in the containment reservoir. The second problem is the belt is broke that turns the brush. ... Vacuums

My Craftsman wet/dry vac is not picking anything up. It seems have some suction...not as much as it used to. I just replaced the filter and that did not help. Any suggestions?


Disconnect hose and check suction at vacuum port. if suction is poor ther turn off, lift lid, e stick coat hanger wire in port from the backside diverter. also, clean filter. ... Vacuums

I have a Craftsman brand shop vac [model # 113.77420]. It is still picking items when I sweep with it, but it has developed a very high pitched squealing sound whenever I turn it on. The sound makes it almost impossible to use. Any thoughts? Thanks, Bruce


I have the same problem with a CTC Shop Vac. It's he bearings ... they're worn out and dry ... no lubrication. I've trid taking the motor apart and lubricating the bearings, then it runs super for a few uses but then the squealing starts again. Oi ... Shop Vac 925-09-62 QSP Plus Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0633 seconds