Having problems with your Bissell 3576 CleanView II Bagless Upright Vacuum ?

It turns on but the spinner underneath wont work now

\015 So I just dropped my vacuum and now it will turn on but the spinner thing underneath the vacuum wont spin and pick up any dirt...Can someone PLEASE help me..i just bought this vacuum and dont have the receipt to return it..THanks\015

Answers :

Turn the vacuum so the bottom is facing up..
\015\012Take out the scews in the plate that surounds the brush and take it off..
\015\012The belt should be firmly on the brush and the motor..
\015\012If the belt has come off the motor - pull out the side of the brush that the belt connects to.. Put the belt back on the motor post and the brush.. It might be a tad tough going back in because the belt should have a little tension..
\015\012Once the belt is on and brush in place - put plate back on..
\015\012
\015\012Hope this helps ;o)
Repair Help & Product Troubleshooting for Bissell 3576 CleanView II Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

It turns on but the spinner underneath wont work now


Turn the vacuum so the bottom is facing up..\015\012Take out the scews in the plate that surounds the brush and take it off..\015\012The belt should be firmly on the brush and the motor.. \015\012If the belt has come off the motor - ... Bissell 3576 CleanView II Bagless Upright Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

My bissell proheat carpet cleaner wont turn on. Its plugged in and everything but wont turn on. I've had it for a few years but its always worked before. Do they have to heat up if I haven't used it in a while?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha


... Eureka Smartvac 4870 Bagged Upright Vacuum

Our Dyson upright vaccumms beater bar wont move. the vaccumm will **** up air but the bar underneath wont move. The gears are not working property.


It could be the clutch that's causing the problem or the belt. Bring your vacuum to a local repair shop and have it look at, but it sounds like it could be either one of those problems. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

When I turned on the sweeper it would not start. I put a different power cord on it and it worked fine. now it won't start but the light on the brush and the bag full will flash when i turn it on and off but it wont start. i have 2 of these doing the same thing. do you have any idea what could be wrong. I have checked for clogs but have found none. Bob


Its sounds to me like the computer board inside the machine has gone bad. Keep in mind that the filters in these machine do need to be replaced regularly to keep the vacuum working correctly. Any good vacuum shop should be able to fix your problem. R ... Windsor SR12 Sensor Bagged Upright Vacuum

Hi my hoover vacuum, stopped working,does not even turn on,I accidently went over a shoelace but stopped before the shoelace went in, ,,becuase of that the belt came off,and then i put belt back on, and now it wont even turn on


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

VACCUUM GOES ON, MOTOR WORKS, BRUSH WONT TURN WHEN THE VACCUM IS TURNED ON.


Check the belt, and remove any objects clogged in the roller system ... Dyson Vacuums

MY Devant 2GB MP4 player wont turn on, but when i plug it to a computer it turns on and charges then after an hour i tried pressing the on button, it does not work


... Vacuums

Tried pressing in red button and switch next to on button to get roller working but not made any difference - still wont turn (any no suction)


Hi there,I'm sorry to hear you're having difficulty with your DC24. If you haven't been able to reset the brushbar using the reset switch on the cleaner head, I'd encourage you to get in touch with us directly so we can provide further assist ... Dyson Ball DC24 Bagless Upright Vacuum

I shampooed my carpet and later that day went to use the Kirby Sentria and it wont turn on... it has always worked fine up to this moment, what could be wrong?


Specifically the bag attachment area. There is a detent on the bag boot that depresses a safety switch. Make sure the bag boot is rotated clockwise into its seated position. ... Kirby Heritage II Vacuum

My dyson works fine in the bare floors mode but when i turn it to carpet mode it makes loud noise and wont **** up.


You need to replace the belt. Here is a link to the manual and to the belts you need:Dyson DC07 Manual and Belts ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc04 wont pick up,motor working,replaced clutch assembly but still dosnt turn brushes


You need to go through a process of elimination. You are better doing that here: Dyson advice forums ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Water leak I just bought this steamer a few days ago, and already I am having problems, when I fill the water tank that your suppost to fill the water runs out before I even turn the machine on. I have tried using plugs to keep it from doing this just so I can shampoo my carpet, this seems to work to a point, considering the fact that there are two holes underneath close to the brushes and one just a little ways back from that location. Do you know if this is something that should have plugs or


If you just pruchased this, then it is under warranty, take it along with proof of purchase to a warranty repair shop and have them fix it. If water just runs out, then there may be a seal missing or a water line off. ... Eureka Atlantis 2595A Upright Wet/Dry Vacuum

Dewalt 2gallon corded/cordless vacume...unsed one time brand new wont turn on. motor and switch both tested and work...any ideas


Check the battery contacts... a common problem on this model. they are easily bent and prone to corrosion. ... Dewalt Cordless/Corded Wet/Dry Vac 2 Gallon Vacuum

I am wondering if there is a reset button on the g4 kirby vacuum? I used it 2 days ago works good and today wont even turn on and I have tried several outlets in my house


Hello Sheri_stange.Unfortunately, there's no reset button on this vacuum. What you can do is make sure that the brush roll housing and the bag unit are on firmly as there's a safety switch that will disable the Vacuum to turn on if either ... Kirby G4 Bagged Upright Vacuum

I have a hoover windtunnel v2 the brushes underneath wont turn ? its suppose to be beltless what do i do to fix this


Are you sure it is beltless? What model do you have? Looking at another manual there may be a seperate on off switch for the brushes but would need to know your model to be sure. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hover windtunnel It will start when you plug it in and wont turn off with the switch you have to plug it in and unplug it to get it to work.


I had the same problem with the Hover windtunnel. All I had to do was remove the two screws holding on the handle and then pull the handle off pulling horizontal to the ground. Then I manually turned to swith off. Check it to make sure the switch ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Dyson dc14 animal is falling apart! The canister keeps falling our and now the carpet/floor adjuster doesn't work AND the brush wont turn....tried everything. I live in Half Moon Bay, CA (near San Francisco) where can I bring it to be OVERHAULED? Thanks


The best sol would be to search for vacuum repair half moon bay, ca. To see if there is a vac shop near you. my suggestion's would be either Vacuum Cleaner Shop #(877) 822-8227 or Vacuum solotions #(502) 348-4900. hope this helps ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson vacuum wont turn on at all, switch has not been working properly for a few months.


This sounds like a classic Dyson issue that I deal with time and again. While I may be way off base, take a look at my article http://www.fixya.com/support/t3143954-not_turn ... Vacuums

I have a hoover savvy that the rollers wont turn. I've taken it apart to make sure the brushes are not caught but nothing happens. I only used this vacuum once. It was a floor model when purchased. I just need to figure out what I need to do to get this to work.


Hi there SmartAlec from NelsonVacuums.com.au here. I have to say that if it is not as simple as a belt - I assume that when you checked that the brushes weren't caught that ... Hoover U8125-900 Savvy Bagged Upright Vacuum

MY vaccuum wont suction or turn at the brush bar. The wand works and I already checked/cleaned all the areas the instrucion manual said to.


The DC07 has a "brush control system" operated by a knob on the right side of the base. This knob has two positions: "bare floors" (or "off") and "carpet" (or "auto"). The roller will turn only when the knob is on "carpet", and even then only w ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The spinner that shows that the suction or water is pumping out on the floor will not spin. I have checked the belts they are ok. I have turned it off for a few min. and it doesnt work.


The belts may look fine but they can be stretched or worn. If you haven't replaced them recently I would try that. You can get the belt you need here: ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0565 seconds