Having problems with your Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum ?

Roller brush won't spin (bissel 6390/3910 series)

\015 I was vacuuming and started to smell burning rubber, so we took the floor brush out to clean it out and we also checked the belt. The belt looked fine and the brush was all cleaned out, but when we put it all back together the brush wouldn't spin. By looking at the parts, we don't understand how it can spin (granted, we aren't vacuum experts). The ends of the brush fit into these grooves and we don't understand how it spins when the ends fit tightly into these grooves. When put all together the vacuum still runs, motor pulley still turns, but the belt doesn't turn, and we still get the burning smell (from the pulley rubbing against the belt). We think the solution must be simple, but we're stumped!\015

Answers :

I just fixed mine. It took me all of 10 minutes. Pull the brush out. Stand the brush on end on the edge of your study work bench/table top. while holding the brush vertical( on end) take a small phillips screwdriver and tap using a hammer on the metal pin you see in the middle of the brush. Keep tamping and the whole assembly will come apart. What you will have then is a long metal shaft, 2 bearings(they are acutally skateboard wheel bearings same number same make). Clean the gobbed up hair with a razor blade and then reassemble by tapping back together. The bearing wont be worn out because they are way too tough for a vaccum. We used ride down hills on them! a ten minute fix wow and you wont have to drive to vacuum shop and spend $$ and time
I had the identical problem. One side of my end cap/bearing had actually melted together so that it appeared to be one piece and thus making it impossible for the roller brush to turn. Even though I was able to get the end cap and bearing apart using channel locks the parts were too damaged to use so I've ordered a new brush.
Repair Help & Product Troubleshooting for Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Roller brush won't spin (bissel 6390/3910 series)

I just fixed mine. It took me all of 10 minutes. Pull the brush out. Stand the brush on end on the edge of your study work bench/table top. while holding the brush vertical( on end) take a small phillips screwdriver and tap using a hammer on the meta ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Bissell powersteamer clearview model 8806-roller brush wont spin

... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Roller brush wont rotate my bissell series 3760-5

... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Brush wont spin on my bissell 93z6

... Bissell Heavy-Duty Vacuum Cleaner, 93Z6

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.

You need a new belt. ... Vacuums

Model 2090, bissell quicksteamer brush wont spin

... Bissell 2080 QUICKSTEAMER Upright Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?

Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

Scrub roller wont spin - Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Pull the bottom cover off and replace the drive belt for the brush drum, if the belt is ok then replace the drive motor for the brushes. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My brush roller isn't spinning on my bissell powergroom vacuum

You belt has probably broken or it has stretched to the point where it won't turn the brush against the resistance of the carpet. You need to change the belt. Below are the two possible belts you could need. Check and see if yours is a PowerGroom Pet ... Vacuums

My bissell cleanview helix wont **** up anything on carpet. the brush doesn't spin. any thoughts?

... Bissell Cleanview Helix Deluxe Bagless Upright Vacuum Cleaner 21K3

Brushes wont spin, how do you replace belt - Bissell 9200 Upright Vacuum

Hey, sorry to hear the brushes are not turning. Here's a quick link to instructions on how to change the belt(s). We also have a terrific How-to-Video linked to this also. \015\012 ... Bissell 9200 Upright Vacuum

I have a bissell lift off and the brushes wont spin, i think it maybe because of the internal switch that tells the vacuum that the canister is installed is bad. is there a replacement part for that or do i have to get a new vacuum?

Hi,If you take out the brush roll, holding the ends, make sure that it \015\012spins freely, if not, replace it. Belts stretch after a short time of \015\012use and need to be replaced often.So you could either have a bad brush roll and ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Roller brush does not spin - Bissell 3920 Bagless Upright Vacuum

You either need to replace the drive belt for the roller or clean the ends of the roller where it is held to the vacuum.\015\012The ends of the roller brush become plugged with debris and need to be loosened by hand and perhaps lubricated a bit with ... Bissell 3920 Bagless Upright Vacuum

Bissell Proheat 2x Series 8920 - Brush Belt Metal Shaft Sprocket won't turn

Most likely the brush motor is bad and not turning, part #2036757, would sell for around $23. To get to it, start taking out screws on the top cover, that motor is under the that top access cover. ... Bissell 8910 ProHeat Clear View Upright Vacuum

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?

The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus

... Bissell 6595 Lift Off Bagless Upright Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge

... Vacuums

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.

The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Why wont the brushes spin? I have had this machine for about 3 years and it has always worked great, tonight the brushes will not spin at all, it still sprays and sucks up the water. We took the brushes off and were able to spin them by hand

In this machine there is no belt. The brushes actually spin by vacuum and in the turbine assembly there is a small wheel bearign which rusts out. You will need to remove and repair or replace the turbine and gear assembly P/N should be 43191009 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Bissell healthy home vacuum roller won't spin

Hi Helen. Your Healthy Home vacuum has a lifetime belt. If the belt needs replacing, you should bring it to one of our Authorized Service Centers for repair. Also, here is quick link to troubleshooting steps to assist you: \015\012 ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,

It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?

The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

Electrolux nimble wont run only the roller brush

... Electrolux Vacuums

Brush bar wont turn, Bissell smells like burning rubber

The belt just goes from the motor shaft to the brush roll. Do the ends of the brush trun freely, or is one of them froze up, if so replace the brush roll. If it is ok, try to turn the brush roll by hand, maybe the belt got pinched and won't move. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

My bissell 82h1 roller brush does not work

I think it is belt driven? a broken belt if it uses one or the belt is off the spindle most use to drive it. ... Bissell 82H1 Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0738 seconds